INTERNOISE2014: inter.noise 2014
Melbourne Convention and Exhibition Centre, Melbourne Australia, 16-19 November 2014
Table of Contents
- Sunday 17:00-18:00 Room Plenary Plenary 1
- Monday 08:20-09:20 Room Plenary Keynote 1
- Monday 08:20-9:20 Rooms 219 & 220 Keynote 2
- Monday 09:20-10:40 Room 218 L1a Active control of sound
- Monday 09:20-11:00 Room 217 T8a Sound Quality
- Monday 09:40-10:40 Room 216 C1a Aeroacoustics
- Monday 09:20-10:40 Room 215 A1a Education - outreach to community
- Monday 09:40-11:00 Room 214 H1a Urban sound propagation
- Monday 09:20-11:00 Room 213 Q2a Numerical methods in vibro-acoustics
- Monday 10:00-11:00 Room 212 B4a Machinary N&V - Plant
- Monday 09:20-11:00 Room 211 N1 Speech privacy in buildings
- Monday 09:20-11:00 Room 210 N8a Room acoustics
- Monday 09:20-10:40 Room 209 D1 Road vehicle noise
- Monday 09:20-11:00 Room 208 D4a Pavement modelling and measurement techniques
- Monday 09:20-10:40 Room 207 R1 Underwater acoustics
- Monday 09:40-11:00 Room 206 T4a Noise and health- overall effects and susceptible groups
- Monday 11:00-12:20 Room 220 E1 Railway noise and vibration
- Monday 11:20-12:40 Room 219 P1a Vibration and Shock
- Monday 11:00-12:40 Room 218 L1b Active control of sound
- Monday 11:20-12:40 Room 217 V1a Metrology - calibration and realisation of standards
- Monday 11:00-12:20 Room 216 C1b Aeroacoustics
- Monday 11:00-11:40 Room 215 A1b Education - outreach to community
- Monday 11:40-12:40 Room 215 A2a Education- to the profession
- Monday 11:20-12:00 Room 214 H1b Urban sound propagation
- Monday 11:20-12:40 Room 213 Q2b Numerical methods in vibro-acoustics
- Monday 11:20-12:20 Room 212 B4b Machinary N&V - Plant
- Monday 11:20-12:20 Room 211 N3 Green sustainable buildings
- Monday 11:20-12:40 Room 210 N8b Room acoustics
- Monday 11:00-12:40 Room 209 D2a Vehicle noise vibration and harshness (NVH)
- Monday 11:20-12:40 Room 208 D4b Pavement modelling and measurement techniques
- Monday 11:20-13:00 Room 207 R3a Underwater noise and its control
- Monday 11:20-12:20 Room 206 T4b Noise and health- overall effects and susceptible groups
- Monday 13:40-15:20 Room 220 K2a Applying building envelop design for noise mitigation
- Monday 13:40-15:00 Room 219 P1b Vibration and Shock
- Monday 13:40-15:40 Room 218 L1c Active control of sound
- Monday 13:40-15:00 Room 217 V1b Metrology - calibration and realisation of standards
- Monday 13:40-15:20 Room 216 C2a Airframe/flow-induced-noise
- Monday 13:40-15:40 Room 215 A2b Education - to the profession
- Monday 13:40-15:20 Room 214 H2a Outdoor sound propagation
- Monday 13:40-15:40 Room 213 Q2c Numerical methods in vibro-acoustics
- Monday 13:40-15:20 Room 212 B2 Machinary N&V - Engines
- Monday 13:40-15:20 Room 211 N4a Classroom acoustics
- Monday 13:40-15:40 Room 210 N7a Acoustic criteria in regulations and classification schemes for buildings
- Monday 13:40-15:40 Room 209 D2b Vehicle noise vibration and harshness (NVH)
- Monday 13:40-15:20 Room 208 D4c Pavement modelling and measurement techniques
- Monday 13:40-15:40 Room 207 R2 Underwater noise measurement
- Monday 13:40-15:20 Room 206 S1a Soundscape and its diversity in history and culture
- Monday 15:40-17:00 Room 220 K2b Applying building envelop design for noise mitigation
- Monday 15:40-18:00 Room 219 T1 Reaction to aircraft noise
- Monday 16:00-18:00 Room 218 L2 Signal processing for active control
- Monday 15:40-17:20 Room 217 T8b Sound quality
- Monday 16:00-18:00 Room 216 C2b Airframe/flow-induced-noise
- Monday 16:00-17:40 Room 215 U1 Technical expertise in noise assessment and management
- Monday 15:40-17:20 Room 214 H2b Outdoor sound propagation
- Monday 16:00-18:20 Room 213 Q2d Numerical methods in vibro-acoustics
- Monday 16:00-17:40 Room 212 B1 Fan and duct noise
- Monday 15:40-16:20 Room 211 N4b Classroom acoustics
- Monday 16:40-17:40 Room 211 N2 Healthcare facility acoustics
- Monday 16:00-17:40 Room 210 N7b Acoustic criteria in regulations and classification schemes for buildings
- Monday 16:00-18:00 Room 209 D2c Vehicle noise vibration and harshness (NVH)
- Monday 15:40-18:00 Room 208 D6 Tyre/road noise - tyre factors
- Monday 16:00-18:00 Room 207 R3b Underwater noise and its control
- Monday 15:40-16:20 Room 206 S1b Soundscape and its diversity in history and culture
- Monday 16:40-17:40 Room 206 S2 Soundscape and auditory cognition
- Tuesday 08:20-09:20 Room Plenary Keynote 3
- Tuesday 08:20-09:20 Room 213 Keynote 4
- Tuesday 09:20-11:00 Room 218 M1 Metamaterial
- Tuesday 09:20-10:40 Room 217 G1 Wind turbines -Evaluation at neighbours I
- Tuesday 09:20-10:40 Room 216 C3a EU research projects on aircraft noise
- Tuesday 09:20-10:40 Room 215 A3a Noise policy
- Tuesday 09:20-11:00 Room 214 H3 Noise mapping prediction tools
- Tuesday 09:40-10:40 Room 213 Q2e Numerical methods in vibro-acoustics
- Tuesday 09:20-11:00 Room 212 Q6a Inverse approaches in vibro-acoustics
- Tuesday 09:20-10:40 Room 211 N6a Noise in lightweight structures
- Tuesday 09:20-10:40 Room 210 N8c Room acoustics
- Tuesday 09:20-11:00 Room 209 D2d Vehicle noise vibration and harshness (NVH)
- Tuesday 9:40-11:00 Room 208 D8a Motor vehicle noise - policy and regulation
- Tuesday 09:20-10:40 Room 207 R4 Detection, localisation and classification of sources
- Tuesday 09:40-11:00 Room 206 T3a Effects of noise on humans
- Tuesday 11:00-12:00 Room 220 E3 Railway wheel and rail noise
- Tuesday 12:00-12:40 Room 220 E4 Rail acoustics policy
- Tuesday 11:00-12:40 Room 219 T7 Loudness and other psycho-acoustical parameters
- Tuesday 11:20-12:20 Room 218 M2 Nanomaterials in acoustics
- Tuesday 11:20-12:40 Room 217 G2 Measurement of wind turbine noise
- Tuesday 11:00-12:20 Room 216 C3b EU research projects on aircraft noise
- Tuesday 11:00-12:40 Room 215 A3b Noise policy
- Tuesday 11:00-12:20 Room 213 Q2f Numerical methods in vibro-acoustics
- Tuesday 11:20-12:40 Room 212 Q6b Inverse approaches in vibro-acoustics
- Tuesday 11:00-12:40 Room 211 N6b Noise in lightweight structures
- Tuesday 11:00-12:40 Room 210 N8d Room acoustics
- Tuesday 11:40-12:40 Room 209 S4a Soundscape and methods of evaluation
- Tuesday 11:20-12:00 Room 208 D8b Motor vehicle noise - policy and regulation
- Tuesday 11:20-12:40 Room 207 R5 Bubble acoustics
- Tuesday 11:20-12:20 Room 206 T3b Effects of noise on humans
- Tuesday 13:40-15:20 Room 220 E2 Ground-borne vibration and noise from railways
- Tuesday 13:40-15:20 Room 219 V2a Sound visualization and manipulation
- Tuesday 13:40-15:40 Room 218 L3a Applications and systems for active control
- Tuesday 13:40-15:00 Room 217 G3 Wind turbines - Evaluation at neighbours II
- Tuesday 13:40-15:20 Room 216 C4a New experimental techniques
- Tuesday 13:40-15:20 Room 215 A3c Noise policy
- Tuesday 13:40-15:40 Room 214 H4a Airport noise modelling and measurement
- Tuesday 13:40-15:20 Room 213 Q3a Vibro-acoustic methods for noise control treatments
- Tuesday 13:40-15:20 Room 212 Q7 Modal analysis
- Tuesday 13:40-15:40 Room 211 N6c Noise in lightweight structures
- Tuesday 13:40-15:40 Room 210 N8e Room acoustics
- Tuesday 13:40-15:40 Room 209 D3a Electric / hybrid vehicles
- Tuesday 13:40-15:20 Room 208 D5 Ultralow noise surfaces
- Tuesday 13:40-15:40 Room 207 R6a Underwater noise from pile driving
- Tuesday 13:40-15:00 Room 206 S4b Soundscape and methods of evaluation
- Tuesday 15:40-18:00 Room 220 T6a Psycho-acoustics in noise evaluation
- Tuesday 15:40-18:00 Room 219 T2 Reaction to traffic noise
- Tuesday 16:00-18:00 Room 218 L3b Applications and systems for active control
- Tuesday 16:00-17:40 Room 217 G4 Measurement - Infrasound, LFN, Tonality
- Tuesday 16:00-17:40 Room 216 C4b New experimental techniques
- Tuesday 15:40-16:40 Room 215 U2 Noise management in challenging industries
- Tuesday 16:40-17:40 Room 215 B5 Buy quiet
- Tuesday 16:00-17:40 Room 214 H4b Airport noise modelling and measurement
- Tuesday 15:40-17:00 Room 213 Q3b Vibro-acoustic methods for noise control treatments
- Tuesday 17:00-18:00 Room 213 Q4a Vibration and vibro-acoustic experiments
- Tuesday 15:40-17:40 Room 212 B3 Machinary N&V - Computations
- Tuesday 16:00-18:00 Room 211 N6d Noise in lightweight structures
- Tuesday 16:00-18:00 Room 210 N5 Propagation and generation of low frequency noise in buildings
- Tuesday 16:00-18:00 Room 209 D3b Electric / hybrid vehicles
- Tuesday 15:40-17:20 Room 208 D7 Modelling and mapping traffic noise
- Tuesday 16:00-17:40 Room 207 R6b Underwater noise from pile driving
- Tuesday 16:00-18:00 Room 206 S3 Soundscape and noise control
- Wednesday 08:20-10:40 Room 220 T6b Psycho-acoustics in noise evaluation
- Wednesday 08:20-10:20 Room 219 V2b Sound visualization and manipulation
- Wednesday 08:20-10:40 Room 218 L4a Active vibration control and active structural acoustic control
- Wednesday 08:20-10:20 Room 217 G5 Evaluation of wind turbine noise source mechanisms
- Wednesday 08:20-09:40 Room 216 C5 Aircraft engine noise
- Wednesday 09:40-11:00 Room 216 C6 Jet noise
- Wednesday 08:40-10:20 Room 215 W1 Instrumentation
- Wednesday 08:20-10:40 Room 214 H5 Numerical methods for predicting outdoor sound propagation
- Wednesday 08:20-10:20 Room 213 Q4b Vibration and vibro-acoustic experiments
- Wednesday 08:40-10:40 Room 212 Q5 Vibro-acoustics of lightweight composite panels
- Wednesday 08:20-10:20 Room 211 K1a Noise barriers
- Wednesday 08:40-10:20 Room 210 N9a Impact noise in buildings
- Wednesday 08:40-10:20 Room 209 D9a Mufflers and silencers
- Wednesday 08:40-10:00 Room 208 F1a Noise events from transportation noise
- Wednesday 08:20-10:40 Room 207 R7 Numerical methods in underwater acoustics - Transmission
- Wednesday 08:20-10:00 Room 206 S5 Soundscapes and health related quality of life
- Wednesday 11:00-13:00 Room 220 T6c Psycho-acoustics in noise evaluation
- Wednesday 11:00-13:00 Room 219 V2c Sound visualization and manipulation
- Wednesday 11:00-13:00 Room 218 L4b Active vibration control and active structural acoustic control
- Wednesday 10:40-11:40 Room 217 G6 Measurement - Modeling and propagation
- Wednesday 11:00-13:00 Room 216 C7 Computational aeroacoustics
- Wednesday 11:00-12:20 Room 215 U3 Personal hearing protectors and headsets
- Wednesday 11:00-12:40 Room 213 Q4c Vibration and vibro-acoustic experiments
- Wednesday 11:00-13:00 Room 212 P2 Vibrations in bridges, foot bridges and similar structures
- Wednesday 10:40-12:00 Room 211 K1b Noise barriers
- Wednesday 10:40-13:00 Room 210 N9b Impact noise in buildings
- Wednesday 10:40-12:00 Room 209 D9b Mufflers and silencers
- Wednesday 10:40-12:20 Room 208 F1b Noise events from transportation noise
- Wednesday 11:00-13:00 Room 207 R3 Numerical methods - Interaction with submerged structures
- Wednesday 10:20-11:20 Room 206 K3 Noise control within offshore facilities and maritime vessels
- Wednesday 11:40-13:00 Room 206 Q2g Numerical methods in vibro-acoustics
- Wednesday 14:00-15:00 Room Plenary Plenary 2
- Monday 09:20-Tuesday 18:00 Foyer Posters
All rights reserved. Permission is granted for any person to reproduce a part of any abstract provided that the permission is obtained from the author(s) and credit is given to the author(s) and these conference proceedings.
Sound Sketch: Shaping sound in space and time using loudspeaker arrays
Choi, Jung-Woo
KAIST, Korea
ABSTRACT
The control of the spatial distribution of noise and sound has been widely investigated for achieving passive and active noise control. By extending the concepts of active noise control and zones of quiet, one can sketch sound, i.e., synthesize sound fields of various shapes using loudspeaker arrays to achieve the desired sound quality in a finite zone of interest. Sound sketching involves reproducing existing sound fields as well as creating new shapes of sound fields that can scarcely be observed in common acoustical spaces. In this lecture, two representative problems related to sound shaping are presented: the synthesis of a personal sound zone, and the manipulation of virtual sound sources. Through the shaping of sound in space, sound fields can be focused over a selected area to form a personal sound zone within which a person hears only a specified sound program without being disturbed by other unwanted programs. In addition to focusing sound fields, it is possible to control a sound wavefront to produce virtual sound sources with various radiation patterns in a source-free space. The underlying array signal processing theories, developed since 2000, are introduced in regard to practical systems implemented for various applications. The novel paradigm for sound field control systems, the Sound of Things, is introduced with a sound sketch interface devised to facilitate gesture-based interaction between a person and a sound field.
Full Paper
Can technology deliver acceptable levels of aircraft noise?
Astley, R Jeremy
Institute of Sound and Vibration Research, University of Southampton, United Kingdom
ABSTRACT
Meeting community expectations on aircraft noise has always presented a challenge to aircraft and engine manufacturers and to those involved in airport planning and air traffic management. It has been a critical issue for communities living close to airports since the introduction of turbojet and turbofan powered aircraft in civil aviation in the late 1960s and early 1970s. The technical progress which has been made during this period in reducing aircraft noise at source and mitigating its effects by noise reduction technologies is not widely understood or appreciated by the community. These remarkable achievements will be reviewed here, and an assessment presented of current progress towards meeting ambitious new environmental targets for aircraft entering service between now and 2050. While much has been achieved, opportunities still exist to exploit further significant reductions in noise both for current aircraft layouts but also in the longer term for future aircraft and engines which may differ significantly from current configurations. The main sources of aircraft noise will be reviewed and areas identified in which the greatest noise reductions have been achieved. Areas will also be highlighted where future gains are likely. Much of the discussion will revolve around measures of the noise of a single aircraft at takeoff or approach. This forms the basis for noise certification metrics and the focus of industry efforts to reduce aircraft noise. This is only a part of the complex jigsaw of issues however which define the aircraft noise problem. These include the public's perception of what actually constitutes a noise nuisance and also critically the rate at which an expanding commercial fleet transitions to newer quieter aircraft.
Full Paper
A new era for applications of active noise control
Qiu, Xiaojun (1), Lu, Jing (2), Pan, Jie (3)
(1) RMIT University, Australia
(2) Nanjing University, China
(3) University of WA, Australia
ABSTRACT
The fundamental theories and methods of active noise control (ANC) have become well established over the last 30 years, so fewer academic research projects on ANC are funded nowadays. However, applications of the technology are entering a new golden era with greater numbers of companies investigating the applications of noise control in their products. One good example is the successful application of ANC on Apple's iPhone 5 to increase speech quality in communication by cancelling ambient noise. This paper discusses a number of ANC projects that we have conducted over the last ten years with emphasis on the various challenges encountered in the applications of ANC. Aspects covered include acoustical design methods, recently developed adaptive control algorithms, new control hardware and systems, and new applications. The projects discussed include active control of transformer noise, ANC in natural ventilation windows, and ANC in a communication chassis. Unlike our previous research, all these projects are funded by industry bodies, and their aims are not to perform academic research, but to develop commercial products.
Full Paper
Generation of localized sound using speaker array
Fukaya, Kigen (1), Iwamoto, Hiroyuki (1), Sanada, Akira (2), Tanaka, Nobuo (3)
(1) Seikei univercity, Japan
(2) Industrial Center of Okayama Prefecture, Japan
(3) Tokyo Metropolitan University, Japan
ABSTRACT
This paper presents a methodology of generating a sound field in which the sound energy around the speakers is high while that in the other region is relatively low. Although directional loudspeaker that delivers sound energy only for the specific direction has been discussed in the past literature, such a method leaks sound to outside of the specific area because of reflection of the sound wave. To overcome this problem, a novel methodology of generating localized sound is presented which is based on the phenomena that radiated sound from vibration of a rectangular plate under the specific conditions decays drastically more than normal distance decay effect. First, spatial distribution of a rectangular plate vibration at a frequency where acoustic power becomes extremely low is verified, it being clarified localized sound is generated by coupling certain modes each other. Next, a matrix-type speakers array is used to imitate the spatial distribution that generates localized sound in order to achieve generating a sound field not only at a single frequency but in band-limited spectra. As a result, efficacy of speakers array to generate of localized sound is revealed.
Full Paper
Analysis on the timbre of Ambisonics recording by circular and spherical microphone array using a binaural loudness model
Xie, Bosun (1), Liu, Yang (1)
(1) South China University of Technology, China
ABSTRACT
Ambisonics are a series of flexible sound reproduction systems that decompose and reconstruct sound field by each order approximation of spatial harmonics decomposition. Circular or spherical microphone array has been used for Ambisonics recording. For an array with given radius as well as given number and configuration of microphones, the spatial harmonics signals up to certain temporal frequency and certain order can be derived from the array outputs with appropriate accuracy. When the temporal frequency exceeds the given limitation of array, however, spatial aliasing occurs in the derived spatial harmonics signals. Spatial aliasing in recording causes error in reconstructed sound field, which inevitably change the timbre in reproduction. The present work analyzes the timbre in Ambisonics recording by rigid circular and spherical microphone array. The binaural loudness level spectra are used as a criterion to evaluate the timbre in reproduction. The results indicate that, array recording influences little on the binaural loudness level spectra and thus timbre in final reconstructed sound field providing that the high-frequency limit of microphone array exceeds that of sound field reconstruction. Increasing number of microphones extends the high-frequency limit of array and thus improves the timbre.
Full Paper
Reduction of air space behind piezoelectric absorbing panel using negative stiffness
Yamada, Keisuke (1), Yamagata, Kenta (2), Utsuno, Hideo (1)
(1) Kansai University, Japan
(2) Kyoto University, Japan
ABSTRACT
This paper proposes a method of reduction of the air space behind the piezoelectric sound absorbing panel using the piezoelectric elements, negative capacitor, and resistor. Because the air space behind the panel works as an air spring, the natural frequency of the panel is increased by the air spring under the condition that the air space is small. Therefore, the purpose of this research is to decrease the increased natural frequency of the piezoelectric sound absorbing panel due to the air space behind the panel. The negative capacitor and resistor are coupled to the piezoelectric elements bonded on the panel. The piezoelectric elements and circuit give negative stiffness and positive damping to the panel. The governing equations were theoretically derived, and optimum values of the negative capacitance and resistance were respectively formulated. The effectiveness of the proposed method and the theoretical analysis were verified through simulations and experiments.
Full Paper
A stability analysis of cluster active control system of sinusoidal sound in free space
Yu, Haoxin (1), Chen, Kean (1), Sang, Zhiming (2), Tang, Dakai (2)
(1) Northwestern Polytechnical University, Xi\'an, China
(2) Shaanxi Fenghuo Electronics Co. Ltd., China
ABSTRACT
Generally, the implementation of fully coupled multichannel active noise control system which has advantages in improving noise reduction and extending quiet zone requires considerable processing power. A practical method to decrease processing power is to decentralize the control; that is, implement many single input, single output independent controllers operating simultaneously instead of a large multiple input, multiple output system. However, the drawback of decentralized control is the risk of global instability. A new method was proposed for constructing an active noise control system to balance the complexity in multichannel systems and instability in the decentralized system. The proposed method consists of several independent multichannel sub-systems called cluster active control system, which is a modified version of the decentralized system and can improve stability at a reasonable computational cost. The purpose of this paper is to derive conditions under which globally stable control system behavior can be obtained in the case of cluster control for a sinusoidal disturbance. Hence, theoretical analysis and simulations are carried out to achieve the main objective which is to give practical conditions derived from the zero-pole map of the control system. These conditions only take into account the geometrical arrangement of the secondary sources and error sensors.
Full Paper
Psychoacoustic analysis of HVAC noise with equal loudness
Hohls, Silke (1), Biermeier, Thomas (2), Blaschke, Ralf (2), Becker, Stefan (1)
(1) University of Erlangen-Nuremberg, Germany
(2) Audi AG, Germany
ABSTRACT
In order to guarantee maximal comfort inside vehicles, noise pollution has to be minimized. When considering developments especially in electro mobility, one major sound source - the combustion engine - is eliminated. Hence, the ancillary units as sound sources become increasingly unmasked and thus, prevalent. The sound field developed by the heating, ventilation and air conditioning system (HVAC) then essentially affects the perceptible sound field inside the car cabin. For identifying the relevant psychoacoustic parameters for assessing the sound quality of HVAC noise, a listening test, using the preference paired-comparison technique, was performed on seven sound samples of different vehicles in the defrost mode. The sounds were equalized in their loudness on an average level. Thus, the aim of this study was to analyze the correlation between the listeners' preference and additional parameters beside the dominant parameter loudness. It was found that the sharpness, the articulation index and the roughness determine a preference decision when the loudness is eliminated from the sound samples.
Full Paper
Perception of sound quality of product sounds A subjective study using a semantic differential
Hülsmeier, David (1), Schell-Majoor, Lena (1), Rennies, Jan (1), Van De Par, Steven (2)
(1) Fraunhofer IDMT Hearing Speech and Audio Technology, Germany
(2) Carl von Ossietzky Universität Oldenburg, Germany
ABSTRACT
How can quality of product sounds be measured? This question was investigated on basis of shaver, vacuum cleaner and spray sounds, which were matched in loudness according to DIN45631 and were separately presented to subjects. Using open questions, the perception of the sounds was determined and a list with word pairs was created as a basis for a semantic differential. The sounds were presented to subjects in a listening booth and were rated separately for each product group.The data were analysed by means of polarity profiles and factor analyses. Groupings could be found for sounds and word pairs. For the word pairs, one factor representing quality could be found for each product group. This factor, the factor loadings and the answers of the subjects were used as basis for a linear model. The results indicate that spectral and temporal properties of spray sounds correlate with perception of quality. Stationary spray sounds were rated with a high quality in contrast to spluttering sounds. Vacuum cleaners need to sound powerful and functional to be perceived as top quality. Precise, cutting and fast sounds were perceived as top quality for shavers. The results are discussed on basis of auditory models.
Full Paper
Improving sound quality measures through the multifaceted soundscape approach
Schulte-Fortkamp, Brigitte
TU Berlin, Germany
ABSTRACT
Soundscape research represents a paradigm shift in the field of sound evaluation. First, it improves human perception, and, second, it expands on classical physical measurements and makes reference to the use of different investigative measurement methods. This multifaceted approach is basic to improving the validity of the research outcome on any subject or phenomenon, and it avoids systematic errors that can occur when relying on only one approach. The soundscape approach considers the conditions and purposes of a sound's production and how it is perceived. Consequently, it is necessary to understand that the evaluation of sound is a holistic process. The International Standard ISO/DIS 12913-1 has as its purpose the enabling of a broad international consensus on the definition of 'soundscape' and its respective evaluation. It is more than urgent to understand that there is the need to provide a solid foundation for communication across disciplines and professions with an interest in achievements on better solutions for the people concerned.
Full Paper
Contribution of single sounds to sound quality assessments of multi-source environments
Skoda, Sabrina (1), Steffens, Jochen (2), Becker-Schweitzer, Jörg (1)
(1) Duesseldorf University of Applied Sciences, Germany
(2) McGill University Montreal, Canada
ABSTRACT
In everyday life people are surrounded by several sound sources which complement each other in complex acoustical environments. Different models to predict annoyance reactions to combined noise sources, pre- dominantly based on loudness summation, have recently been proposed. However, it is still not understood how single sounds contribute to the evaluation of pleasantness of a multi-source environment, as the perceived sound quality is subject to numerous superposition and interaction effects of sounds with diverse acoustical characteristics. Therefore, the fundamental relationship between assessments of single and combined sound sources was investigated in the course of a listening experiment. Various sounds commonly occurring in suburban areas, including traffic noise, sounds from technical devices and natural sources, were evaluated in laboratory separately and combined in pairs with regard to their pleasantness. The results show that the com- bination ratings correspond to the sum of the single assessments and their interaction (R2 = .95). Moreover, less pleasant sounds have greater influence than pleasant sounds, which can be attributed to masking effects and the negativity bias. A regression model is proposed that provides a highly accurate prediction for simple sound combinations in laboratory context. Consequently, validation for acoustical environments of higher complexity is needed in future.
Full Paper
Study on evaluation method of the pure tone for small fan
Yamaguchi, Takao (1), Minorikawa, Gaku (1), Kihara, Masayuki (2)
(1) Hosei University, Japan
(2) Sharp Corporation, Japan
ABSTRACT
In the field of audio, visual and information technology equipment, small fan noise which includes many pure tones becomes annoying components. Pure tones are caused by the electromagnetic force of motor, the flow interference between blades and spokes, the acoustic modes of the structure and so on. These tones become not only the main contribution to the overall sound pressure level, but also unpleasant component. Some metrics for the pure tone have been presented, however the one which specified for small fan noise has not been developed. In this study, evaluation of multiple pure tones generated by small fan was attempted and examined by using sensory test.
Full Paper
Study on modeling of flow induced noise using Lighthill\'s analogy and boundary element method
Mori, Masaaki (1), Masumoto, Takayuki (1), Ishihara, Kunihiko (2), Oshima, Takuya (3), Yasuda, Yosuke (4), Sakuma, Tetsuya (5)
(1) Cybernet Systems, Japan
(2) Tokushima Bunri University, Japan
(3) Niigata University, Japan
(4) Kanagawa University, Japan
(5) The University of Tokyo, Japan
ABSTRACT
We have calculated the flow-induced sound pressure field using Lighthill's acoustic analogy by means of an acoustic boundary element method (BEM). For this calculation, firstly, an unsteady flow field is calculated using a computational fluid dynamics (CFD) solver. Then acoustic sources are extracted from the result and transformed into the frequency domain. Finally, these are used as quadrupole acoustic sources in the acoustic BEM model. In the BEM calculation, because some of the CFD grid points exist quite close to the BEM elements, for example 100 times smaller than the element length, so the contribution from the sources must be evaluated quite preciously. To achieve this, the elemental integration of the source contribution is introduced. We have validated the procedure (CFD/BEM approach) by comparing with an experimental data. The first validation is a comparison of the acoustic pressure generated by a low Mach number flow past a 3D circular cylinder. The second validation is a comparison of the acoustic pressure induced by a low Mach number flow in a bending duct. Finally the transmitting acoustic pressure which is originally induced by a flow through an elastic structure is calculated by the structural-acoustic coupled model.
Full Paper
Direct numerical simulation of flow and acoustic fields around an air-reed instrument with tone holes
Yokoyama, Hiroshi (1), Kobayashi, Masaki (1), Onitsuka, Hirofumi (2), Miki, Akira (2), Iida, Akiyoshi (1)
(1) Toyohashi University of Technology, Japan
(2) Yamaha Corporation, Japan
ABSTRACT
In order to clarify flow and acoustic fields around a recorder with opened and closed tone holes, direct aeroacoustics simulation was performed with compressible Navier-Stokes equations. For validation of the computational accuracy, the velocity distribution and sound pressure level were experimentally measured. The predicted velocity profile of jet ejecting from the windway is in good agreement with that of experiment. The numerical results show that the fundamental frequency and sound pressure level of predicted sound are almost the same as that of experiments. The path of the standing wave of the recorder was estimated with the pressure distribution. The open-end corrections found to be longer than those for a conventional simple pipe due to the effects of the impinging jet on the edge and the uniform flow in the resonator. When the vortices of the jet from the windway are getting near to the edge, strong deformation of the vortices occurs and expansion wave radiates in the resonator. The amplitude and phase of the acoustic particle velocity are almost the same as those of the jet itself. It indicates that the acoustic field amplifies the fluctuations of the jet and maintains the acoustic and fluid relations.
Full Paper
Aerodynamic noise produced in flow around an automobile bonnet
Yokoyama, Hiroshi (1), Nakajima, Takahiro (1), Shinohara, Taishi (1), Miyazawa, Masashi (2), Iida, Akiyoshi (1)
(1) Toyohashi University of Technology, Japan
(2) Honda R&D Co., Japan
ABSTRACT
To clarify the mechanism and conditions of the intense acoustic radiation from flows around a curvilinear body with a kink shape in an accelerated boundary layer, the experiments were performed with a low noise wind tunnel. The effects of the free-stream velocity and angle of the model to the horizontal surface in the downstream of the kink, γ, on the sound and flow fields were investigated. Consequently, the intense tones can be observed at γ = 5°, 10°. In these cases, the velocity fluctuations showed that the periodic vortex formations occur with the flow separation due to the kink. Also, it was clarified that the fundamental frequency of the tones has ladder-type behavior with reference to the flow velocity. These results indicated that the feedback loop, which consists of the vortex formation due to the kink and acoustic radiation around the trailing edge, is formed. Meanwhile, the intense tones did not radiate for the larger angle of γ = 15°, where the vortex formation does not occur around the kink shape by the lack of flow separation. Also, for the smaller angle of γ = 0°, the large flow separation prompted turbulent transition and the intense tones do not radiate.
Full Paper
Role for an Acoustical Society Journal
Burgess, Marion
UNSW Canberra, Australia
ABSTRACT
The objectives for most acoustical societies include the concepts of promoting and advancing acoustics as well as supporting acousticians. The common means for achieving these objectives are the organization of meetings and the production and distribution of a publication. The basic publication is a newsletter that provides the means to keep the members informed on activities. As the society grows it is usual that the publication develops to include articles to better promote acoustics in the region. It is then not long before the society is producing a journal with a combination of news, notes and articles. This paper will discuss the role, benefits and challenges for a medium sized society in the production of a journal, using the journal Acoustics Australia as the example.
Full Paper
Education and Outreach: I-INCE Publications
Burroughs, Courtney B (1), Thompson, James (2)
(1) INCE, USA
(2) NIOSH, USA
ABSTRACT
One of the objectives of the member societies of the International Institutes of Noise Control Engineering (I- INCE) is the dissemination of useful information on the effects of noise, descriptions of the mechanisms and transmission of noise, and methods of noise control. Publications supported by I-INCE are one of the primary mechanisms for the dissemination of useful information on noise and its control. This paper presents an overview of the I-INCE publications, e.g. the Noise Control Engineering Journal, Noise News International and INCE conference papers. The objectives of these publications, mechanisms of publications and methods of access to these publications are discussed. Strategies for improving the usefulness to I-INCE members of these publications are outlined.
Full Paper
Communicating the noise message
Parnell, Jeffrey (1), Wassermann, John (2)
(1) Dept of Planning and Environment, Australia
(2) Wilkinson Murray Pty Ltd, Australia
ABSTRACT
This paper revisits the key aspects of noise communication addressed by the authors in a previous paper and provides a summary of current practice and suggests strategies for improving the communication of information on noise so that it achieves the best outcomes. A discussion is presented on the limitations of noise assessments and public understanding as well as the consequences of good/bad noise communication. In addition, this paper also examines contemporary issues of changing expectations in communities and the dissemination of misinformation.
Full Paper
Public participation at measures to reduce noise in Germany
Zeisler, Annett
Federal Environment Agency, Germany
ABSTRACT
An essential part of a modern noise reduction strategy is the involvement of the public. This important approach is implemented in the European Environmental Noise Directive. According to this Directive, noise action plans will be developed with the participation of the public. In Germany, the individual participation in planning processes is increasingly in the focus of public interest and in political discussions. Especially, in context of large-scale infrastructure projects such as the expansion of an airport. The goal-oriented implementation of the participation process and the challenges of an effective participation are demonstrated at prominent examples. Moreover, proposals for a further development of the legal requirements of the public participation at EU as well as international level will be presented. In this context, special consideration is given to measures of a clear and effective participation. The aim of these activities is to achieve a higher acceptance for official decisions of great importance. The involvement of the public in the decision-making process could also have a positive effect on their annoyance reaction because noise is often perceived as less loud if people are directly involved in the process.
Full Paper
Comparison of acoustic pulse propagation between scale-model measurements and three-dimensional simulation over real-life urban topography
Oshima, Takuya (1), Ishizuka, Takashi (2), Kamijo, Takahide (1)
(1) Niigata University, Japan
(2) Shimizu Corporation, Japan
ABSTRACT
In Inter-Noise 2013, the authors presented a study comparing acoustic propagation measurements over a 1:100 scale model of a real-life urban topography and large-scale three-dimensional finite-difference time- domain simulations. The results were presented in octave-band sound pressure levels. As a sequel to the 2013 paper, this paper compares the results in time domain. The waveforms of acoustic pulse propagation are computed by inverse filtering the source responses of an electric spark generator of the measurements and a Gaussian pulse of the simulation. The results show excellent matches at line-of-sight and single diffraction receiver positions in overall waveform structure, especially in arrival times of the diffracted and reflected pulses. The arrival time matched even after 0.7 s of traveling time. However, major discrepancies are observed at a receiver position which is affected by a combination of double diffraction and multiple reflections and positions affected by deep triple diffractions. Furthermore, in such positions, the simulated waveforms are found to have more energy in higher frequency. The discrepancies are possibly attributed to the use of rigid surfaces in the simulation and the lack of air absorption correction in the measured data processing.
Full Paper
Calculation of sound propagation with highly reflective environments
Probst, Wolfgang
DataKustik GmbH, Germany
ABSTRACT
Engineering models applied to calculate noise levels in residential areas caused by traffic sources are ray-based approximations of the real wave propagation. Difficulties arise if many reflective objects like buildings influence sound propagation and if reflections contribute significantly to the resulting levels. There are different techniques to deal with these problems and all of them have their pros and cons. Some of them are discussed with special attention for the precision and repeatability necessary if these calculation methods shall be applied to check the conformity of infrastructure projects with existing legal requirements. Noise prediction for low noise back-yards near roads with heavy traffic and methods to calculate the levels increase in street canyons are discussed. It is shown that the assumption of specular reflection in nearly all calculation methods is a good approximation even with diffuse reflecting facades, but nevertheless limits the finally possible accuracy of noise prediction.
Full Paper
Model based monitoring of traffic noise in an urban district
Van Der Eerden, Frits (1), Graafland, Freek (1), Wessels, Peter W (1), Segers, Arjo (1), Salomons, Erik M (1)
(1) TNO, The Netherlands
ABSTRACT
Noise control for an urban district starts by understanding the actual noise situation. A correct understanding is needed to take appropriate and cost efficient measures. For a noise burdened urban district, surrounded by road and rail traffic, the traffic noise as well as the annoyance has been measured. The size of the district is approximately one square km. With the help of 35 microphones, applied in a scalable sensor network, the time-varying sound levels were recorded. These results were coupled to an engineering model to obtain the sound levels for the complete district as well as to discriminate between road and rail traffic noise. Also, a data assimilation technique has been applied to increase the agreement between the measurement and model results. For example, for Lden sound levels the standard used source strengths for road and rail needed to be adapted to better match the sound level measurement results. In a separate paper these corrected sound levels at the façades are coupled to annoyance survey results to derive a local exposure-response relation. The annoyance survey also indicated the importance of peak levels and vibrations. This is further investigated by considering the measured noise dynamics.
Full Paper
Experimental analysis of the noise shielding by a green roof in response to rainfall
Van Renterghem, Timothy (1), Despriet, Mathias (1), Botteldooren, Dick (1)
(1) Ghent University, Belgium
ABSTRACT
A vegetated roof top (green roof) was shown to be the most promising building envelope greening measure to achieve quietness at a shielded side. In addition, such a measure comes with many ecological and economic benefits in addition to noise reduction. Noise abatement by green roofs has been assessed extensively before by detailed full-wave numerical simulations, by in-situ and full-scale laboratory diffraction experiments, and by characterizing the acoustic properties of the materials involved. In general, the absorption coefficient of any porous material is negatively affected by the presence of water. To assess the influence of rainfall on the acoustic performance of a green roof, a controlled in-situ diffraction experiment has been set up. The measurements, lasting for about 1.5 months, show a decrease in shielding with increasing moisture content, especially in the frequency range between 315 Hz and 1250 Hz. The difference in shielding between dry and (near) saturated state may amount up to 8 dB. Outside this frequency interval, diffraction over the green roof was hardly influenced by the volumetric water content of the substrate.
Full Paper
Enhancing the low frequency vibration reduction performance of plates with embedded acoustic black holes
Conlon, Stephen (1), Fahnline, John (1), Feurtada, Phil (1), Semperlotti, Fabio (2)
(1) Penn State / ARL, USA
(2) Notre Dame, USA
ABSTRACT
Embedded Acoustic Black Holes (ABH) have been investigated as a passive treatment for noise and vibration control. The ABH effect is produced from a plate thickness power taper which results in a local asymptotic reduction of wave speed within the ABH. Theoretically the local wave speed approaches zero at the ABH center, causing the waves to take an infinite amount of time to reach the center, thus the waves are "trapped" in the black hole. This work focused on the low frequency performance of plates with periodic grids of ABHs for structural vibration and radiated sound reduction. Plates with embedded ABH grids were modeled with detailed Finite / Boundary Element models. The results show the ABHs reduce the narrow band vibration and radiated sound power by up to approximately 20 dB over that of the heavier uniform panel, at frequencies below the theoretical cut-on of the ABH as a broadband absorber. The low frequency performance of the ABH grids can be tailored based on the low frequency vibration characteristics of the ABH unit cell. Detailed results for several ABH plate configurations will be presented giving insight into key ABH low frequency design performance characteristics.
Full Paper
FE based measures for structure borne sound radiation
Klaerner, Matthias (1), Marburg, Steffen (2), Kroll, Lothar (1)
(1) Technische Universität Chemnitz, Germany
(2) Univerität der Bundeswehr München, Germany
ABSTRACT
The sound emission of thin-walled radiating components is a common objective of structural optimisation. Acoustic measures are not implemented in common FE-codes. Thus, different velocitiy based measures will be compared: the kinetic energy, the equivalent radiated power (ERP) and the lumped parameter model (LPM). The most common approach - the ERP - is based on the sound intensity in normal direction and the sound pressure on the radiating surface. Assuming a unit radiation efficiency all-over the surface and neglecting local effects, this is a common approach for an upper bound of structure borne noise. Therein, the sound power finally results from the squared velocity integrated over the radiating surface and the constant fluid impedance. As ERP usually requires extra post processing to consider the velocity in normal surface direction, the kinetic energy is essential in common FEA results including all velocity components apart from the normal direction, too. Thus, it is less accurate but maybe usable for optimisation abilities. In contrast, LPM is a simplification of the Rayleigh-integral and thus gives quite accurate results but requires significant higher computational costs than ERP. Possibilities and limits of estimating the emitted sound power by these three methods will be shown.
Full Paper
Experimentally uncertainty quantification in numerical and analytical beam models
Langer, P (1), Sepahvand, K (1), Krause, M (2), Marburg, Steffen (1)
(1) Universität der Bundeswehr München, Deutschland
(2) Isko - engineers AG, Deutschland
ABSTRACT
In modern industrial processes such as developing new products, virtual prototyping is state of the art method to ensure short design cycles while dealing with low cost pressure. In order to meet these criteria, efficient and reliable simulations must be available. Numerical methods, especially the Finite Element Method (FEM) are commonly used in various industrial fields e.g. the automotive sector, aircraft design and ship construction. The scope of this paper is to enhance the reliability of numerical models utilizing FEM when considering uncertain parameters of the underlying structure. Such parameters can be system related, i.e. geometry, material behavior, boundary conditions and mesh density as well as general assumptions in the process of modeling. Two well-known beam theories, i. e. Euler-Bernoulli and Timoshenko theory, have been utilized. At FE level, various elements available for modeling of beam structures in ABAQUS have been compared and evaluated. Experimental modal analysis have been performed on beam specimen to validate the results from analytical and FE models due to parameter uncertainties. A comparison between the numerical and analytical simulations with experiments reveal the element types with minimum deviation with regard to parameter uncertainties. Having sufficient knowledge of the dynamic behavior of simple beam samples, the complexity will be increased. This investigation developed instructions on how detailed a numerical model must be built to get satisfactory results.
Full Paper
Prediction of airborne and structure borne sound transmission through hearing protectors using FEM
Sgard, Franck (1), Brummund, Martin (2), Viallet, Guilhem (2), Boyer, Sylvain (2), Doutres, Olivier (3), Nelisse, Hugues (1), Laville, Frederic (2), Petit, Yvan (2), Boutin, Jerome (1)
(1) IRSST, Canada
(2) ETS, Canada
(3) University of Sherbrooke, Canada
ABSTRACT
Individual hearing protection is a short term solution frequently used to protect workers against noise exposure. This work is part of a larger research program on the evaluation of real world attenuation of hearing protection devices (HPD) such as earplugs and earmuffs. Its objective is to develop a Finite Element (FE) model to predict both the airborne and structure borne sound transmission through an ear canal/hearing protector system. The model can help providing a better understanding of the acoustical behavior of this system and hence help designing better HPD ultimately. FEM can account for realistic ear and hearing protector geometries, materials with complicated physical behavioral laws and complex transmission phenomena through the different coupled domains in particular the tissues surrounding the ear canal. Several comparisons between numerical predictions and experimental results are presented. The sound transmission through the system is investigated using power balances and sensitivity analyses are carried out to identify the key parameters which govern the acoustic behavior of the system. The importance of parameters such as the system geometry, the coupling between the different domains and the loadings is discussed together with the characterization of the physical properties of each domain.
Full Paper
Analytical and numerical approaches to predict radiated sound power of fluid-loaded cylindrical shells
Zhang, Yilin (1), Jiang, Weikang (2), Peters, Herwig (3), Kessissoglou, Nicole (3)
(1) Shanghai Jiao Tong University, China, UNSW Australia, Sydney, Australia
(2) Shanghai Jiao Tong University, China
(3) UNSW Australia, Sydney, Australia
ABSTRACT
Prediction of the vibro-acoustic responses of fluid-loaded cylindrical shells is important for underwater vehicles. In this work, a number of analytical and numerical approaches to predict the radiated sound power of a fluid-loaded cylindrical shell are compared. In the first approach, an analytical methodology is used whereby the equations of motion for the cylindrical shell are solved by the method of modal superposition. The shell displacements are represented by a Fourier series and auxiliary functions. The radiation sound power is calculated by integrating the product of the pressure and velocity on the surface of the cylinder. In the second approach, an integrated analytical and numerical approach is implemented whereby the vibrational response of the cylindrical shell is used as an input to a boundary element model. The radiated sound power is subsequently obtained using the boundary element method. In the final approach, a fully-coupled finite element/boundary element model of the fluid-loaded cylinder is developed. Results for the radiated sound power from the various analytical, hybrid analytical/numerical and fully coupled numerical approaches are compared.
Full Paper
Analysis of Sound Propagation in Finned Tube Bundle of HRSG in Power Plant
Ahn, Sungjong (1), Lee, Sanghyuck (1), Ha, Jinwoong (1), Shin, Eontak (1)
(1) DOOSAN Heavy industries and Construction, South Korea
ABSTRACT
The HRSG (Heat Recovery Steam Generator) generates high noise level due to the exhaust noise from gas turbine and is reduced as passing HRSG component. The HRSG consists of four major components - inlet duct, main casing, outlet duct and stack. Occasionally, additional noise reduction structures such as inlet shroud and silencer are required to satisfy the noise limit level. Thus, the prediction of noise level may lead to significant design problem. In this paper, we developed prediction method for the noise reduction level of main casing. The main casing consists of finned tube bank which is considered as a silencer. The FEA (Finite Element Acoustic) is applied to noise attenuation process of tube bundle. The test in actual finned-tube bank is performed for the validation of analysis.
Full Paper
Fatigue Life Estimation of Piping System for Evaluation of Acoustically Induced Vibration (AIV)
Izuchi, Hisao (1), Nishiguchi, Masato (1), Lee, Gary Y H (2)
(1) Chiyoda Corporation, Japan
(2) Shell Global Solutions, Malaysia
ABSTRACT
One of the key design parameters to a process plant with large capacity is the risk of AIV (Acoustically Induced Vibration) on the flare piping system. AIV is a piping vibration phenomenon exhibiting high frequencies caused by large acoustic power generated by the pressure drop across a PRV (Pressure Relief Valve). The evaluation method for susceptibility of piping to AIV fatigue failure was first proposed by Carucci and Mueller around 30 years ago. Since then, several developments were reported. However, there has not been publication with reference to fatigue life estimation in relation to the AIV phenomena. This paper proposes a procedure to calculate the fatigue life for the AIV based on actual operating condition, design fatigue life curve, etc. In this procedure vibration stress level can be obtained from the expected sound power level. The stress level was then used to estimate the fatigue life using design fatigue life curve and AIV experimental data. It is hoped that this procedure would allow for possible AIV failures to be classified corresponding to the actual plant operation. This kind of AIV evaluation would be useful to determine the priority of the countermeasure to mitigate piping failure caused by AIV in the existing plant.
Full Paper
Numerical and Experimental Study on Mechanism of Low Frequency Noise from Heat Recovery Steam Generator
Tang, Hongyun (1), Jiang, Weikang (1), Zhong, Zhenmao (2), Zhao, Yingjiu (2)
(1) Shanghai Jiao Tong University, China
(2) Huadian Heavy Industries Co. Ltd, China
ABSTRACT
The low frequency noise from heat recovery steam generator (HRSG) makes dominant contribution to the noise on the boundary of plant, which generation mechanism is investigated in this presentation. The non-stationary flow field and aeroacoustic noise is studied with hybrid numerical simulation, which is comprised of CFD method based on Large Eddy Simulation (LES) and acoustic analogy by using Ffowcs Williams-Hawkings equation. Models of cylindrical tube, fin-tube and tube array are established respectively to investigate the feature of vortex noise. The results of numerical simulation are compared with the acoustic intensities measured at the site. It can been understood from the simulation that the flow passing through the heat exchanger tube will induce vortex shedding, which results in the low frequency noise in HRSG. The vortex noise of a cylindrical tube lead to the obvious characteristic tone frequency as same as the vortex shedding frequency, but the spiral fin reduces the characteristic frequency and sound level. For the tube array of heat exchanger, due to the enhanced interaction of the flow field among tubes, the vortex noise is narrowband noise with some bandwidth. More targeted methods can be used for noise reduction of HRSG according to the research results.
Full Paper
Improvement of body-conducted speech recognition using model estimation
Nakayama, Masashi (1), Ishimitsu, Shunsuke (1), Nakatani, Satoshi (2)
(1) Hiroshima City University, Japan
(2) Yamaguchi University, Japan
ABSTRACT
One problem with speech recognition is a low performance in noisy environments because it is easily influenced by aerial in air. Although the sound quality of body-conducted speech (BCS) and regular speech are different, with BCS recognition, it is possible to recognize an utterance in noisy environments with a rating of 98 dB sound pressure level (SPL) in our previous study. In this study, we investigate how to improve BCS recognition performance using model re-estimation methods of ML and MAP. An acoustic model uses parameters such as mean vector, covariance matrix, weight, and transition probability. Recognition performance is improved by model re-estimation of speech and BCS using maximum likelihood and maximum a posteriori methods, respectively. We confirmed that improvements in recognition performance are achieved for practical through the re-estimation of the covariance matrix and mean vector.
Full Paper
An electronic database of speech sound levels
Nash, Anthony
Charles M. Salter Associates, USA
ABSTRACT
In early 1970's, the U.S. Environmental Protection Agency sponsored a research program involving speech sound levels in various noise environments. Bolt, Beranek and Newman (BB&N) conducted this research program under contract. Among other tasks, BB&N measured speech sound levels under controlled conditions from subjects using five categories of speech effort. In 1977, a summary report of the research program was prepared. This report was supported by a companion data supplement containing a statistical analysis of sound pressure levels measured at one meter from 97 individual subjects in an anechoic chamber. The data were obtained from a one-third-octave-band real-time analyzer, processed by a mini-computer, and then printed in the form of 482 cumulative statistical distributions. The 140,000 sound pressure levels in this printed data supplement have now been converted to an electronic database to create a convenient and efficient resource for the acoustical community. The data can be used for many purposes, including the prediction of speech privacy for a variety of speech efforts. This paper summarizes the contents of the database and discusses its possible applications.
Full Paper
The Influence of Abfusor Configuration to the Speech Privacy and Intelligibility in an Open Plan Office
Sarwono, Joko (1), Rachman, Arinda Puspita (1), Azzahra, Iva R Nisa (1), Utami, Sentagi Sesotya (2)
(1) Institut Teknologi Bandung, Indonesia
(2) Universitas Gajah Mada, Indonesia
ABSTRACT
Open plan office is an office plan which minimizes the use of full room divider such as a private office. Nowadays, open plan office is preferred because it provides many advantages such as working mobility and increasing teamwork between co-worker and managerial. This concept also fulfills today energy management issues. Open plan office provides minimum energy consumption especially in lighting and air conditioning. On the other hand, a problem that usually faced by worker whose work in open office plan, which has correlation in speech comfort, are audial interference caused by another sound or noise, and loss of speech privacy. One way to overcome this problem is by applying absorber - diffuser (abfusor) surfaces. In this paper, simulation of abfusor application in an open plan office model was done by using finite element and ray-tracing method. The simulation was carried out with the reference of ISO 3382- 3:2012 for Open Plan Office - measurement of acoustic parameter. Parameters that were varied in this simulation include absorption coefficient, scattering coefficient and the formation of abfusor surfaces. In situ measurements in the real Open Plan Office which was modeled in the simulation were conducted to provide comparison to the based model. The Simulation was used to determine the parameters of abfusor which provides optimum values to increase speech privacy and speech intelligibility for the open plan office model.
Full Paper
Preliminary study of the acoustic behavior concerning an innovative prototype for indoor modular partitioning
Simões, Gonçalo (1), Patrício, Jorge (2), Faria, Paulina (1)
(1) FCT-UNL, Portugal
(2) LNEC, Portugal
ABSTRACT
This paper presents a preliminary acoustic study concerning the development of the first prototype of a patented removable module for interior partitioning. It is a prefabricated, vertical element for division of interior spaces that does not require the use of gutters or technical support. A set of such modules, linearly disposed, will create a division, allowing the personalization of any indoor area, including open office spaces, rooms, among others. The main characteristic that distinguishes this element from the existing solutions available on the market is that its mobility relies exclusively on a set of integrated bearings at the base of each module. Through an incorporated elevation system, the user can lower the module, move it to the desired position and re-elevate it until pressed against the ledge of the ceiling, making it stable. In this sense, and taking into account its acoustic behavior, several tests were made in the LNEC acoustics lab. Airborne sound insulation tests for different typologies of the prototype were conducted, according to the applicable standards EN ISO 354:2003, EN ISO 717-1:2013 and EN ISO 10140-2:2010. Some important conclusions and analysis of the prototype viability were extracted.
Full Paper
Speech Privacy and Intelligibility in Open-Plan Offices as an Impact of Sound-Field Diffuseness
Utami, Sentagi Sesotya (1), Sarwono, Joko (2), Al Rochmadi, Nurwachid (1), Suheri, Nanan (1)
(1) Universitas Gadjah Mada, Indonesia
(2) Institut Teknologi Bandung, Indonesia
ABSTRACT
The research is based on ISO 3382-3:2012, a standard for speech privacy quality measurement in open-plan offices. Predicted speech privacy and distraction distances, the quality of speech intelligibility, and the diffuseness of the sound fields were observed.
Within the past few decades, a new paradigm has emerged where reverberation control is not the only solution for good room acoustics. In certain open-plan office, quality of speech privacy and intelligibility should be similar for each workstation by creating a diffuse sound field. In many spaces, abfusor for absorption and diffusion are solution in a form of acoustic panel, furniture and other elements, such as bookshelves in offices.
The measurement in this research utilized multi-microphones. The degree of diffuseness was done by evaluating the coherences of impulse responses measured. Values of T30, C50, and RASTI were also evaluated. Further analysis on the sound field diffuseness was done by evaluating the coherence of early and late reflections, and also occurrences of the comb-filtering effect. Subjective evaluation of selected workstations was also conducted. The methods utilized in this research demonstrate the ability for acousticians and architects to evaluate the effect of diffuseness on speech privacy and intelligibility quality of an open-plan office layout.
Full Paper
Psychoacoustic analysis of preference reverberation time for Gamelan Bali Concert Hall
Nitidara, Ni Putu Amanda (1), Sarwono, Joko (1), Merthayasa, I G Nyoman (1)
(1) Institut Teknologi Bandung, Indonesia
ABSTRACT
Lately, there has been increasing interest to design acoustic concert hall for Indonesia traditional music, for example Gamelan Bali. In order to obtain a good and comprehensive design, some research on acoustical properties of Gamelan itself must be conducted. One of the main concerns was to find the optimum value of reverberation time for Gamelan music. Unlike the orchestra and classical music performance, preference value of reverberation time for Gamelan Bali is not known yet. Psychoacoustic research was conducted to obtain the preference of reverberation time for Gamelan Bali. A number of respondents were included in the experiment to give the subjective ratings. The subjects were divided into three groups based on their knowledge and experience of Gamelan Bali music. The results suggest that group which is accustomed to Gamelan music produced more significant results in their subjective ratings than the other groups. Based on that results, the preference value of Gamelan reverberation time was concluded.
Full Paper
Micro-perforated sheets as day-light ceilings
Nocke, Christian (1), Hilge, Catja (1), Scherrer, Jean-Marc (2)
(1) Akustikbüro Oldenburg, Germany
(2) BARRISOL S.A.S, France
ABSTRACT
The theory of microperforated panel sound-absorbing constructions has been introduced by D.-Y. Maa in 1975. Many different applications of micro-perforated sound absorbing materials have been introduced. Materials that have been used to be micro-perforated have been metal, wood, plastics and many others. Stretched sheets used as ceilings, wall coverings and other set-ups have been applied for more than 40 years. In modern buildings ceilings often need to combine different functions, e.g. thermally activated and sound absorptive or sound absorptive and light emitting. With the micro-perforated sheets absorptive day-light ceilings can be built. 3D-shapes as well as printed sheets can be used for architectural or design purposes. Also the fully transparent micro-perforated sound absorber offers new design possibilities. In this contribution measured sound absorption coefficients of various set-ups with micro-perforated materials as well as combinations with different porous materials will be presented.
Full Paper
Application of an in-situ measurement method using ensemble averaging technique to material development
Okamoto, Noriko (1), Otsuru, Toru (2), Tomiku, Reiji (2), Kamimizu, Takaaki (2), Yamaguchi, Makoto (3), Okuzono, Takeshi (4)
(1) Ariake National College of Technology, Japan
(2) Oita University, Japan
(3) Kumamoto University, Japan
(4) Kobe University, Japan
ABSTRACT
An in-situ measurement method using ensemble averaging technique, i.e., EA method, is applied to evaluation for absorption characteristics of multi-functional interior materials using porous mortar in the research and development phase. First, absorption characteristics of small specimens are measured by the EA method in a reverberation room, and the repeatability of the measurement result is confirmed. Next, absorption characteristics of eight kinds of the porous mortars with different fine aggregate and target voids are measured by the method, and their absorption characteristics are compared with each other. Finally, the effect of finishing materials on absorption characteristics of the porous mortar is examined.
Full Paper
The Design of MPP and its Application to Enhance the Acoustics of a Real Auditorium
Sarwono, Joko (1), Prasetiyo, I (1), Andreas, S (1), William, A (1)
(1) Institut Teknologi Bandung, Indonesia
ABSTRACT
Micro Perforated Panels (MPP) backed by air cavity is an acoustic absorber based on the Helmholtz resonance mechanism. MPP is potential to be an alternative acoustic absorber amid the carcinogenic issues of porous material. It is however, MPP has several limitations in its application. One of them is its narrow absorption bandwidth. One way to overcome this problem is by arranging some MPPs with particular parameters working on different absorption peaks to deal with wideband absorption as commonly required in room acoustic cases. In this paper the MPP were designed by simulation using Dah - You Maa model. There are four parameters that can be adjusted to get the right sound absorption coefficient from the MPP; those are panel thickness, pore diameter, cavity depth, and perforation area. Validations on the simulation results are carried out through Impedance Tube Measurements using transfer function method based on ISO 10534-2 standard. The paper also discusses the application of the MPP into a real auditorium by modeling and simulation. The aim is to overcome the acoustics problem for speech, classical music, and Indonesian traditional music performance in the auditorium. The influence of MPP's configurations on the acoustics of the auditorium are presented and discussed.
Full Paper
Withdrawn3
Withdrawn3,
ABSTRACT
Withdrawn3
Selection of state highway bridge expansion joints in noise sensitive areas
Chiles, Stephen
NZ Transport Agency, New Zealand
ABSTRACT
Noise generated by vehicles passing over expansion joints has not been a significant factor in the selection of joint types for most existing state highway bridges in New Zealand. In response to concerns raised by residents living near a proposed new bridge in Wellington, the NZ Transport Agency commissioned research into noise from existing bridge joints on the state highway network to gain a better understanding of design and selection parameters. The research primarily used vehicle mounted noise and vibration transducers to obtain comparative data for a relatively large number of existing joints. Even for the same joint types significant variability in noise generated was found, meaning no clear ranking of different joint types could be established from the data. The installation and maintenance quality of the road surface and joint appears to be a significant factor in noise generated. Finger joints were found to provide consistent performance with noise towards the lower end of the range measured. Modular joints without surface treatment generated high noise levels. This paper sets out the methodology used for the measurement of bridge expansion joint noise and summarises the key findings from the research.
Full Paper
Road traffic facade treatment in Israel
Epstein, David
Epstein Acoustics Ltd., Israel
ABSTRACT
This paper outlines the program for facade treatment for traffic noise in Israel. The main principals of the program are: Facade treatment is only provided as part of a statutory plan for a new roadway or a substantial change to an existing road, monetary compensation is never given in lieu of treatment, the facade noise levels are determined by calculation only, using maximum potential noise-producing traffic conditions, the criteria for facade treatment are 64 dBA for residential buildings and 59 dBA for public buildings, the type of treatment is based on the amount the facade noise level exceeds the criterion. The average costs of facade treatments are 80,000 NIS ($A25,000) for dwellings in multi-storey buildings, 210,000 NIS ($A65,000) for single dwellings, 950,000 NIS ($A300,000) for public buildings. Over the last 10 years, approximately 1,500 dwellings have been treated.
Full Paper
Towards a reduction of noise emission of powered two-wheels - Part 1
Lelong, Joel (1), Chatagnon, Roger (1), Clerc, Christian (2), Jamin, David (3), Seigner, Maxime (3), Thivant, Michael (2)
(1) IFSTTAR/LAE, France
(2) Vibratec SA, France
(3) Peugeot Scooters, France
ABSTRACT
Transportation in urban areas is often synonymous of traffic congestion. In the last decade, this situation led users to give up passenger cars and incited them to adopt powered two-wheelers (PTW), better adapted to the traffic hazards. However, the question of the noise emitted by PTW remains a concern for the population. In France, these vehicles are quoted in second position in the opinion surveys relative to the transportation noise. The main objective of the French research project Ascoot (Acoustique des scooters et des motocycles) is to propose solutions aiming to reduce the noise emitted by the most represented PTW in the current traffic. This paper summarizes the results obtained on the acoustical investigation of a panel of ten PTW (including an electric powered scooter). Global and third-octave noise analysis has been performed, relying on the classical Controlled Pass-by procedure, and on a determination of the directivity characteristics. Pass-bys at constant speed, with acceleration and deceleration have been considered, and the influence of mechanical parameters, as the engine capacity, is also analyzed. The noise emission of PTW has been finally compared with those of other means of transportation usually met in urban zones (light vehicles, medium heavy vehicles, buses, trams).
Full Paper
Towards a reduction of noise emission of powered two-wheels - Part 2.
Thivant, Michael (1), Clerc, Christian (1), Jamin, David (2), Gauthier, Quentin (2), Lelong, Joel (3), Chatagnon, Roger (3)
(1) Vibratec SA, France
(2) Peugeot Scooters, France
(3) IFSTTAR/LAE, France
ABSTRACT
Transportation in urban areas is often synonymous of traffic congestion. In the last decade, this situation led users to give up passenger cars and incited them to adopt powered two-wheelers (PTW), better adapted to the traffic hazards. In the frame of the French research project Ascoot (Acoustique des scooters et des motorcycles), this paper focuses on the acoustic optimization performed on two scooters, including diagnosis and computation methodologies, leading to technical solutions implemented on 2 prototypes. The acoustic sources were located and quantified by acoustic imaging on roller benches, and the vibration behavior was characterized by means of experimental modal analysis (EMA) and measurement in operation. A simulation model was build for solutions design: excitation forces were derived from the measured combustion pressure and from a cinematic model of the engine moving parts, whereas structural dynamic response was computed by a Finite Element Model (correlated with EMA). An optimization of muffler design was also performed using transfer matrix models. The implementation of the noise reduction solutions on both prototypes is in progress; a minimum of 3dB noise abatement is expected.
Full Paper
Test sections to study the acoustical quality and durability of thin noise reducing asphalt layers
Bergiers, Anneleen (1), De Visscher, Joëlle (1), Denolf, Katleen (1), Destrée, Alexandra (1), Vanhooreweder, Barbara (2), Vuye, Cedric (3)
(1) BRRC, Belgium
(2) Flemish Agency Roads and Traffic, Belgium
(3) University Antwerp, Belgium
ABSTRACT
Within the context of the European Noise Directive, action plans have been established. Noise reducing road surfaces are seen as a cost-efficient measure for traffic noise abatement. Therefore ten test sections were installed in May 2012 in Belgium, with the objective of integrating noise friendly bituminous wearing courses in the Flemish road surface policy in a later stage. Eight test sections are paved with hot laid, bituminous wearing courses with a thickness of maximum 30 mm and a maximum content of accessible voids of 18 %. The other two sections consist of a double layer porous asphalt (PA) and a stone mastic asphalt (SMA) (reference section). The acoustical quality assessed during measurement campaigns in the first two years after construction is discussed in this paper. Statistical Pass-By (SPB) and Close-ProXimity (CPX) measurements are performed according to ISO 11819 within certain time intervals to follow up the evolution. Also other important factors, like durability, are studied. Resistance to raveling and adhesion to the base course are critical parameters for the lifetime of a thin noise reducing asphalt layer because of the high void content and limited thickness. BRRC measured the raveling resistance on test plates made with the asphalt mixtures sampled at the construction site. Tensile adhesion and shear bond tests were performed on drilled cores to measure the adhesion of the wearing course to the base course. Results of these laboratory raveling and adhesion tests are linked to the evolution on site and to the evolution of the noise measurement results.
Full Paper
Investigating lateral porosity effect on air pumping noise from connected road cavities with CFD simulations
Conte, Frédéric (1), Klein, Philippe (1), Bérengier, Michel (1)
(1) IFSTTAR, France
ABSTRACT
Several mechanisms induced by the tyre/road interaction contribute to the generation of rolling noise. The road texture has a significant role in this process, together with the possible porosity of the road pavement. The latter may influence the noise sources in the high frequency range in which air pumping is supposed to contribute. Even on dense road surfaces with no vertical porosity, possible air flow allowed by the road texture in the contact patch is equivalent to the effect of a so-called "lateral" porosity which is reckoned to have an influence on the source strength.
In this paper, the effect of this lateral porosity is studied with a modelling approach using Computational Fluid Dynamics (CFD). This approach allows the highlighting of some phenomena occurring in the contact patch such as air compression due to the tyre rolling process or air drainage. Simulations are carried out for a smooth tyre and road textures made of more or less connected cavities. A parametric study is presented in the case of a 2D academic configuration to show the influence of air flow resistance in the contact zone on air pumping noise. Finally, air pumping mechanism is simulated for a 3D configuration.
Full Paper
Reduction of vehicle noise at lower speeds due to a porous open-graded asphalt pavement
Donavan, Paul
Illingworth & Rodkin, Inc.
ABSTRACT
Vehicle noise measurements were made on an arterial roadway in San Rafael, California before and after a 25 mm overlay of open graded asphalt concrete (OGAC). The purpose of these measurements was to document any reduction in vehicle noise due to the overlay on a 0.8 km section of pavement prior to repaving the entire length of the roadway. The posted speed limit along this test section is 56 km/hr. Of particular concern was the reduction of noise produced by medium and heavy duty trucks accessing a quarry. To quantify the noise reduction, statistical isolated pass-by (SIP) measurements were conducted before and after the overlay along with 10-minute Leq's with traffic counts, and on-board sound intensity measurements (OBSI). The SIP measurements indicated a 9.2 dB reduction for light vehicles averaging 64 km/hr, 5.1 dB for heavy trucks under cruise/deceleration averaging 48 km/hr, and 3.1 dB for heavy trucks under acceleration averaging 42 km/hr. The hourly Leq for all vehicles was reduced by 5.0 dB. The OBSI measurements displayed reductions of 3.5 dB implying that porous nature of the OGAC was significantly influencing the measured wayside noise reduction.
Full Paper
A study on comparison of noise reduction effect of single-layer drainage asphalt pavement and double-layer drainage asphalt pavement : Part 1 sound power level and frequency characteristic in initial construction
Mori, Hisho (1), Ishikawa, Kenichi (1), Ueta, Tomotaka (1), Noguchi, Eiji (1), Yoshida, Motoomi (1), Kokusho, Masami (1), Nagaoka, Hironori (1)
(1) Oriental Consultants Co., Japan
ABSTRACT
This paper describes noise reduction effect of the double-layer drainage asphalt pavement that is one of the measures of road traffic noise. The data used in the study was researched in 1999-2003.The purpose is to study sound power level and the frequency characteristic in initial construction by comparing the single-layer drainage asphalt pavement with double-layer drainage asphalt pavement. Result of the comparison of the two types, it was found that double-layer drainage asphalt pavement have the noise reduction effect, about 3dB at light vehicles and slight effect at heavy vehicles. Peak frequency of the double-layer drainage asphalt pavement is around 500-630Hz. In addition to, in the near 1000Hz, A-weighted power spectrum of double-layer drainage asphalt pavement is lower than that of single-layer drainage asphalt pavement by 7dB.
Full Paper
Comparison of road and laboratory measurements of tyre/road noise
Swieczko-Zurek, Beata (1), Ejsmont, Jerzy (1), Ronowski, Grzegorz (1), Taryma, Stanisław (1)
(1) Technical University of Gdansk, Poland
ABSTRACT
Tyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated with laboratory methods is to ascertain that tyre interfaces with pavement that has texture, porosity and mechanical impedance the same as with the real road surface. The paper presents results of tests performed by the Close Proximity Method (with test trailer Tiresonic Mk.4) and drum method where very similar or exactly the same surfaces are used. The reported measuring program includes tests performed on an innovative poroelastic road surface called PERS.
Full Paper
AQUO Project - Modelling of ships as noise source for use in an underwater noise footprint assessment tool
Audoly, Christian (1), Rousset, Céline (1), Leissing, Thomas (1)
(1) DCNS Research, France
ABSTRACT
Recent researches outline the need to mitigate underwater noise footprint due to shipping, in order to prevent negative impact on marine life. Within this context, the final goal of the European AQUO project (www.aquo.eu), which started in October 2012 for 3 years, is to provide to policy makers practical guidelines, in order to mitigate underwater noise impacts of shipping noise on marine life. Those guidelines will be based on solutions regarding ship design, including propeller and cavitation noise as well as solutions related to shipping control and regulation. In a first part, this paper will give an overview of the project. In a second part, we'll focus on the introduction of the ship as a noise source in a noise map prediction model. Underwater radiated noise of different categories of ships is represented in a parametric form along frequency, speed and ship size. For that purpose, using available experimental data, a new method is introduced to derive parametric models, based on the decomposition of total radiated noise into three components (machinery noise, propeller noise, and cavitation noise). Each component is defined by a specific "pattern" accounting for the variation of noise with frequency and ship speed. In the last part of the paper, these models are used to determine noise footprint indicators on a test case, and the influence of taking into account or not the horizontal directivity of the noise sources is studied.
Full Paper
Shipping noise impacts on marine life
Cato, Douglas H
DSTO & University of Sydney, Australia
ABSTRACT
Concerns about the impact of noise of shipping on marine life, has led to the recent publication by the International Maritime Organisation of guidelines for the reduction of noise from commercial shipping. This paper puts the noise from shipping in context with other sounds in the ocean, addresses the potential impact of noise from shipping, the difficulties of assessing the impact and the likely effectiveness of mitigation measures. It draws on underwater noise studies around Australia that included areas of low shipping densities, allowing reliable characterisation of natural ambient noise at frequencies of shipping noise. This low frequency ambient noise has been difficult to determine in the high shipping areas where most ambient noise studies have been made. The paper also draws on studies of the effects of noise on marine mammals. Noise from many distant ships across an ocean basin produces a general nondescript background noise known as "traffic noise" where the contribution of any single ship is not detectable. Noise from a nearby ship reaches higher levels than traffic noise but is present for short times and close distances. Noise from a close ship can be positive if it causes an animal to move away and avoid collision.
Full Paper
Ambient noise forward prediction from measured characteristics and high resolution modeling
Eller, Anthony I (1), Heaney, Kevin D (1)
(1) Oasis, Inc., USA
ABSTRACT
An analysis of temporal statistics of ocean ambient noise level time series data is used to determine basic characteristics such as the coherence time of noise level, the frequency distribution and spectrum of noise level fluctuations, and the expected duration of noise excursions from the mean. Conclusions are drawn from this analysis about the effective design of noise surveys and about noise exposure times to marine mammals. Simple formulas are presented to describe forward projection of noise levels in the near term future based on first- and second-order Markovian processes. In addition detailed propagation modeling of the noise from discrete shipping, coupled with appropriate source motion models, is used to support noise forward prediction.
Full Paper
Directionality and coherence of underwater noise and their impact on sonar array performance
Zhang, Zhi Yong
DSTO, Australia
ABSTRACT
Fundamentally, sonar detection depends on extraction of the target signal from underwater noise by spatial and temporal processing of the received inputs. Spatial processing involves coherently adding, with appropriate weighting and phasing, the inputs from distributed sensor array elements to extract the more directional (more correlated) signal from the less directional (less correlated) noise. Knowledge and understanding of the directionality and coherence characteristics of underwater noise is therefore important for the optimum design, operation, and performance assessment of sonar arrays. This paper reviews ambient noise directionality measurements in both deep and shallow waters, with particular emphasis on the medium frequencies where sea surface-generated noise dominates. We discuss the effects of the environmental propagation conditions on the level and directionality of the ambient noise. The noise directionality patterns are interpreted in terms of sound propagation characteristics influenced by sound speed profiles, surface ducts, surface and bottom reflections, internal waves, and range-dependent bathymetries. We also illustrate the effect of noise directionality on spatial processing gain by considering the response of simple sonar arrays.
Full Paper
Daytime and night-time aircraft noise and cardiovascular disease near Heathrow airport in London
Hansell, Anna (1), Blangiardo, Marta (1), Fortunato, Lea (1), Floud, Sarah (1), De Hoogh, Kees (1), Fecht, Daniela (1), Ghosh, Rebecca E (1), Lazlo, Helga E (1), Pearson, Claire (1), Beale, Linda (1), Beevers, Sean (1), Gulliver, John (1), Best, Nicky (1), Richardson, Sylvia (1), Elliott, Paul (1)
(1) Imperial College London, UK
ABSTRACT
Background. Few studies have investigated associations of aircraft noise with cardiovascular health. We investigated this in areas exposed to noise from London Heathrow airport.
Methods. A small area study was conducted in 12,110 census output areas covering 3.6 million residents. Risks for hospital admissions and mortality in 2001-05 were assessed in relation to aircraft noise in 2001, adjusted for relevant confounders. Night (Lnight) and daytime (LAeq,16h) aircraft noise were assessed separately.
Results. Higher aircraft noise was associated with higher relative risks for hospital admissions and mortality from stroke, coronary heart disease (CHD) and cardiovascular disease. Risk estimates were higher for night-time than daytime noise. Adjusted risks were highest for stroke, with RR 1.29 [95% CI 1.14 to 1.46] for Lnight and RR 1.08 [95% CI 1.02 to 1.14] for LAeq,16h for >55dB vs. <50dB. All linear dose-response relationships were statistically significant for hospital admissions but not for mortality, except for CHD and LAeq,16h.
Discussion. This research attracted a high level of policy interest. However, the impact of this and other recent papers on policy decisions such as increased airport capacity in England is currently unclear. Priority areas for follow-up health research into aircraft noise need to be considered.
Full Paper
Noise sensitivity modulates the auditory-cortex discrimination of sound feature changes
Heinonen-Guzejev, Marja (1), Klyuchko, Marina (1), Heikkilä, Kauko (1), Spinosa, Vittoria (1), Tervaniemi, Mari (1), Brattico, Elvira (2)
(1) University of Helsinki, Finland
(2) University of Helsinki & Aalto University, Finland
ABSTRACT
Noise sensitivity refers to physiological and psychological internal states of any individual, which increase the degree of reactivity to noise. There are only few studies on the neural mechanisms underlying noise sensitivity. Mismatch negativity (MMN) is a component of the auditory event-related potential (ERP), generated in the supratemporal lobe of the brain, that is elicited by any discriminable change in some repetitive aspect of the ongoing auditory stimulation. In this study, we recruited 61 healthy adult subjects (age range 19-46 years) and measured their MMN to several sound feature changes inserted in a music-like sequence and administered the noise sensitivity questionnaire. With the help of this method we studied how the neural discrimination of sound changes (as indexed by MMN) is associated with noise sensitivity (as indexed by the questionnaire). The results showed that noise sensitivity had an influence on MMN to sound changes in timbre, with lower MMN responses in individuals with high noise-sensitivity scores than in those with low noise-sensitivity scores. According to the literature available this is the first study on this topic.
Full Paper
Four electrophysiological studies into noise sensitivity
Shepherd, Daniel (1), Hautus, Michael J (1), Lee, Jenny (1), Mulgrave, Joe (1)
(1) Auckland University of Technology, New Zealand
ABSTRACT
Noise sensitivity is present in many clinical populations, describes approximately 20% of the general population, though little is known about its underlying mechanisms. We present findings from four electrophysiological studies designed to expose possible differences in electrophysiological measures between noise sensitive and noise resistant individuals. Noise sensitivity was estimated using self-report measures, while electrophysiological indices included both cardiac (heart rate, heart rate variability) and electroencephalographic (event-related potentials, alpha persistence) measures. All four studies were designed with reference to pre-existing theoretical frameworks. While the findings from all four studies were not definite enough to decide a likely mechanism, they do suggest that electrophysiological investigation of noise sensitivity is viable and in need of further investigation.
Full Paper
Traffic noise in relation to self-reported mental health
Turunen, Anu W (1), Yli-Tuomi, Tarja (1), Tiittanen, Pekka (1), Halonen, Jaana (2), Männistö, Satu (1), Lanki, Timo (1)
(1) National Institute for Health and Welfare, Finland
(2) Finnish Institute of Occupational Health, Finland
ABSTRACT
Noise can cause physiological and psychological stress. Our aim was to study whether outdoor traffic noise levels in Finland are associated with self-reported mental health. Data from the FINRISK 2002 and FINRISK 2007 studies regarding Helsinki, Vantaa, and Turku (n=4,167) were used. Data on the current use of sleep medication, sedatives, and antidepressants, feelings of depression, and doctor-diagnosed depression and other psychiatric illnesses within the past 12 months were obtained from a self-administered questionnaire. Noise (Lden) at the most exposed facades of the residential buildings was modelled using Nordic prediction method and ESRI ArcMap 10 software. Poisson regression models to calculate relative risks (RR) were stratified by sex and adjusted for age, marital status, education, occupation, neighbourhood income, smoking, alcohol consumption, physical activity, BMI, chronic disease, and exposure to traffic-related air pollution. Among those exposed to ≥55 dB, the RR estimates for psychotropic medication use and the prevalence of depression and other mental illnesses were statistically non-significant and varied between 0.86 and 2.02 (men) and 0.74 and 1.05 (women) when compared with the lowest exposure category (<45 dB). Outdoor traffic noise levels in urban areas in southern and south-western Finland were not associated with decreased self-reported mental health.
Full Paper
Exhaust noise control case study for 2800 class locomotive
Croft, Briony (1), Brown, Stephen (2), Miller, Aaron (2), Parker, Andrew (2)
(1) SLR Consulting Canada Ltd, Canada
(2) SLR Consulting Australia Pty Ltd, Australia
ABSTRACT
In NSW, Environment Protection Authority Licences for railway systems activities define noise limits for locomotives applying for permission to operate on the network. This paper describes a case study involving one particular locomotive class (the 2800 class) that had been refused permission to operate in NSW on the basis of low-frequency noise emissions. This paper describes investigations into the locomotive noise and muffler performance, and the steps taken to re-design the muffler to optimise its performance. The objective was to reduce low frequency noise emissions to comply with the EPA licence requirements. The project achieved a reduction in overall Lmax noise levels of up to 5 dB in the highest engine notch settings. The low frequency benefit (in the 25 Hz and 50 Hz one-third octave frequency bands) was of the order of 8 dB. The locomotive class has subsequently been granted approval to operate in NSW.
Full Paper
Railway-noise reduction effect and aged deterioration properties of softer rail pad
Saito, Hidetoshi (1), Ninomiya, Masaki (1), Shimizu, Kenta (1), Takeda, Yoji (1), Sato, Daigo (2)
(1) West Japan Railway, Japan
(2) Railway Technical Research Institute, Japan
ABSTRACT
To lower the elastic rigidity of the track is known as one of the countermeasures against railway-noise. In this study, a field test in which the standard rail pads were replaced by the softer rail pads were conducted in order to evaluate the railway-noise reduction effect of the softer rail pads. In addition, the noise measurements were conducted in another field where the softer rail pads were installed at several periods up to 60 months and the material properties of some of the installed rail pads were measured. As the results, the relationship between railway-noise reduction effect and the aged deterioration properties of the softer rail pads was evaluated quantitatively.
Full Paper
Considering the perception of combined railway noise and vibration as a multidimensional phenomenon
Sharp, Calum (1), Woodcock, James (1), Waddington, David (1)
(1) University of Salford, UK
ABSTRACT
Classical models for predicting annoyance due to combined noise and vibration have typically taken the form of a summation of the magnitudes of the individual stimuli. In this paper, the perception of combined railway noise and vibration will be investigated as a complex multidimensional phenomenon. In a laboratory study, 30 subjects were exposed to 10 combined railway noise and vibration stimuli and asked to make paired comparison judgements of annoyance and judgements of pairwise dissimilarity. A multidimensional scaling analysis on the results revealed a perceptual space of 4 dimensions. Correlations between these perceptual dimensions and objective parameters of the noise and vibration signals were then tested in an attempt to find which, if any, noise and vibration parameters may be related to these perceptual dimensions. Once correlating parameters were found, a multiple regression model was developed to predict total annoyance due to combined railway noise and vibration as a function of these parameters. The final multidimensional regression model has a very strong and significant correlation coefficient (0.99, significant at the 0.001 level) and is able to accurately predict total annoyance as a function of spectral characteristics of the noise and vibration stimuli and the duration of the combined stimulus.
Full Paper
Railway vibration reduction using impact dampers
Yang, Wonseok (1), Ahn, Sangkeun (1), Koh, Hyo-In (2), Park, Junhong (1)
(1) Hanyang University, South Korea
(2) Korea Railroad Research Institute, South Korea
ABSTRACT
The use of impact dampers for reducing railway vibration induced from moving wheel loads and consequent noise generation is presented. The impact dampers for efficient reduction of impact vibration induced by moving loads were designed and verified using simple dynamic models. To test the performance of the impact dampers, the vibration of a simplified beam attached with various impact dampers was measured. The performance of the impact damper on reducing the transient vibration of railway is investigated. The effects of clearance and mass ratio on vibration reduction was analyzed. The numerical solutions using finite element method were verified using the experimental results to find the vibration reduction mechanism. The result was utilized to reduce rolling noise radiation from moving trains.
Full Paper
Footfall vibration analysis of a high precision manufacturing facility
Gaekwad, Jason (1), Lee, Yong Keat (1), Mackenzie, Neil (1)
(1) Aurecon, Australia
ABSTRACT
High tech manufacturing facilities often have specific requirements regarding vibration of floor structures to ensure precision manufacturing is not compromised by vibration induced displacement of components. This paper outlines the design methodology used to mitigate footfall-induced vibration in one such proposed facility. The vibration design process involved an on-site assessment of a similar existing building within the facility to determine the response of typical spans (elevated or on grade) to footfall excitation. Finite element modelling and analyses of proposed constructions were then conducted. The results of this study allowed for floor constructions meeting the specified ASHRAE Vibration Criteria to be accurately determined and priced during the concept stage of the project.
Full Paper
Analysis on propulsion shafting coupled torsional-longitudinal vibration under different applied loads
Huang, Qianwen (1), Liu, Jia (1), Zhang, Cong (2), Yan, Xinping (2)
(1) Wuhan University of Technology, China
(2) Wuhan University of Technology, China, Key Laboratory of Marine Power Engineering and Technology Ministry of Transportation, China
ABSTRACT
With the improvement of the requirements of large ships to ship economy, the coupling dynamics problem of the ship propulsion shafting is particularly prominent. Theoretical method for propulsion shafting coupled vibration needs to be solved to improve the reliability of the propulsion shafting and raise the sailing performance of the ship. This paper mainly studies on the coupled torsional-longitudinal dynamics analytical theory and numerical simulation of the propulsion shafting. Different kinds of incentives can cause different kinds of coupling responses. The changes of displacement and rotation angle caused by coupled torsional- longitudinal vibration of the propulsion shafting is studied by the finite element method. Through comprehensive analysis for the coupling response of the propulsion shafting under the condition of different applied loads individually and simultaneously, the research reveals the dynamics mechanism of coupled torsional-longitudinal vibration and puts forward the theoretical guidance for coupled torsional-longitudinal vibration of the propulsion shafting.
Full Paper
Vibration of a curved subsea pipeline due to internal slug flow
Reda, Ahmed M (1), Forbes, Gareth L (2), McKee, Kristoffer K (2), Howard, Ian M (2)
(1) Curtin University, Australia,Qatar Petroleum, Doha, Qatar
(2) Curtin University, Australia
ABSTRACT
Subsea oil and gas pipelines undergo vibration due to "slug" flow within the internal fluid contents of the pipeline. This slug flow is generated by the differences in density of the internal fluid. It acts as a traversing force along the length of the pipeline and causes structural vibration of unsupported pipeline spans. The resulting vibration of the pipeline may cause high cycle fatigue due to these fluctuating forces. Previous modelling of a moving slug within pipelines has been undertaken for straight pipe span sections. As unsupported pipeline spans are often curved, understanding the impact this curvature has on the traversing fluid load is important. This paper presents a Finite Element model to investigate the effect pipeline curvature has on the slug flow induced forces, resulting in vibration and hence possible fatigue damage to the pipeline structure. Furthermore, the paper presents a technique for using commercial finite element packages for analysing the dynamic response of curved beams to time variant moving loads.
Full Paper
Investigations of eddy current vibration damping
Ruber, Karel (1), Kanapathipillai, Sangarapillai (1), Randall, Robert Bond (1)
(1) UNSW Australia, Australia
ABSTRACT
Eddy currents are generated in electrically conductive materials such as copper in response to a moving magnetic field and they generate forces in the opposite direction of the relative movement of the magnetic field to the conductive material. Those forces have been used for braking applications and are proportional to the relative velocity between the conductive material and the magnetic field, similar to viscous damping forces in vibration attenuation applications.This paper investigates various geometrical configurations of magnet and copper assemblies with the purpose of quantifying and maximising the eddy current forces. The effects of air gaps, magnetic field strength, orientation and surface area are investigated with Finite Element Analysis (FEA) and validated with measurements.
Full Paper
Individual Error Signal Design in Narrowband Active Noise Control Systems
Chang, Cheng-Yuan (1), Kuo, Sen M (1)
(1) Chung Yuan Christian University, Taiwan
ABSTRACT
A narrowband active noise control (NANC) system is often applied to reduce undesired noise with multiple tones whose frequencies are close. Generally, an NANC system uses a single error signal to update a bank of adaptive filters configured in direct/parallel or parallel form. This work proposes a delayless filterbank to participate the frequency components of the error signal into individual error signals with the same frequencies components of the input signals to update the corresponding adaptive filters. A new adaptive algorithm based on the optimized performance index for the enhanced NANC system is also developed. Theoretical analysis is performed to demonstrate the increased convergence speed. Computer simulations are conducted to verify the analysis results and demonstrate the improved performance of the proposed NANC system.
Full Paper
Mitigation of indoor low-frequency noise using single channel active noise control system
Kaneuchi, Ken (1), Nishimura, Koichi (1), Matsui, Toshihito (2)
(1) Osaka Gas Co., Japan
(2) Hokkaido University, Japan
ABSTRACT
In an enclosed space such as a residential space, noise transmitted from outside is amplified at the resonant frequency of the indoor space. The resonant frequency of a residential space is generally close to the low frequency sound of 200 Hz or less. In this study, a single channel active noise control system that has only one secondary source was evaluated experimentally for mitigating low frequency resonance. A standing wave that causes resonance was canceled out by the one secondary source. The similar results were also obtained by numerical simulation utilizing the boundary element method. The simulation is used for arranging an optimal position of active noise control system. From this study, it was confirmed that the single channel active noise control system can mitigate indoor low frequency noise on loops of standing wave efficiently.
Full Paper
A power constrained algorithm for multi-zone sound reproduction
Liao, Xiangning (1), Zheng, Sifa (1), Peng, Bo (1), Lian, Xiaomin (1)
(1) Tsinghua University, China
ABSTRACT
In the process of multi-zone sound reproduction, large output power may be required because of the non-robust for the reproduction system, which will cause loudspeaker failure. To overcome this problem, Least Squares matching approach mostly be adopted to limit total output power. But this method may not assure every loudspeaker power is within the limit. So a power constrained optimization algorithm is proposed to make every loudspeaker power being constrained. Considering power constraint for multi-zone sound reproduction as a convex optimization problem, the primal-dual interior point algorithm is introduced. The simulation performance of reproducing multi-zone sound field in the reverberant room is shown to reach the goal of single power constraint. Therefore, each loudspeaker signal can be realized while minimizing the error between the reproductive and desired sound field.
Full Paper
Noise reduction through active noise control using stereophonic sound for increasing quite zone
Min, Dongki (1), Kim, Junejong (1), Nam, Sangwon (1), Park, Junhong (1)
(1) Hanyang University, South Korea
ABSTRACT
The low frequency impact noise generated during machine operation is difficult to control by conventional active noise control. The Active Noise Control (ANC) is a destructive interference technic of noise source and control sound by generating anti-phase control sound. Its efficiency is limited to small space near the error microphones. At different locations, the noise level may increase due to control sounds. In this study, the ANC method using stereophonic sound was investigated to reduce interior low frequency noise and increase the quite zone. The Distance Based Amplitude Panning (DBAP) algorithm based on the distance between the virtual sound source and the speaker was used to create a virtual sound source by adjusting the volume proportions of multi speakers respectively. The 3-Dimensional sound ANC system was able to change the position of virtual control source using DBAP algorithm. The quiet zone was formed using fixed multi speaker system for various locations of noise sources.
Full Paper
Hybrid active noise barrier with sound masking
Wang, Xun (1), Koba, Yosuke (1), Ishikawa, Satoshi (1), Kijimoto, Shinya (1)
(1) Kyushu University, Japan
ABSTRACT
In this paper, a hybrid active noise barrier (ANB) with sound masking capability is considered. To protect the speech privacy, several sound masking techniques have been developed. However, these sound masking techniques based on the superposition of the masker and original sound will lead to increase in the loudness of the sound after masking. Against this problem, this paper proposes a soundproof system which combines an ANB with a sound masking system. The ANB applies a new type of hybrid active noise control (ANC) system, which can reduce the noise diffraction and the noise propagated to the ear positions of the people behind the ANB simultaneously, to attenuate the conversation sound. Consequently, the required volume of the masker sound will decrease because of the smaller loudness of the original conversation sound in the control area. The sound masking system applies a method which can generate masker based on the frequency properties of the original sound. Several simulations are carried out to investigate the sound attenuation and sound masking performance of this system, and the results show that comparing with the traditional sound masking system, the proposed system needs smaller masker sound to achieve the sound masking effect.
Full Paper
Experimental determination of the difference between free-field and pressure sensitivity levels of half inch laboratory standard microphones
Bacelar Milhomem, Thiago Antônio (1), Martins Defilippo Soares, Zemar (1), Machado Da Rosa Albuquerque, Lucas (1)
(1) Inmetro, Brazil
ABSTRACT
According to the definitions of free-field and pressure sensitivities of a microphone, the two sensitivities will differ from each other because the effects of diffraction and reflection. According to the free-field receiving characteristics of a microphone the difference between of the pressure and the free-field sensitivity is determined not only by the scattering, but also by the relation between the acoustic impedance of the microphone and the radiation impedance. This paper will present a study of the technical specification IEC TS 61094-7 which gives a polynomial function for the difference between free-field and pressure sensitivity levels of laboratory standard microphones, it will present the results of experimental determination for half inch laboratory standards microphones and it will compare the experimental result with the result obtained according to IEC TS 61094-7.
Full Paper
Noise dosimeter microphones: an evaluation of the measurement reliability
Bondarenco, David Bello
Total Safety Ltda., Brazil
ABSTRACT
One of the most practically useful equipment on acoustics is the sound exposure meter, commonly known as noise dosimeter, widely spread on the industry to estimate potential hearing loss of the workers. Despite its importance, the noise dosimeter is much underestimated, having generally lower quality components when compared to other equipment of acoustics metrology field, i.e. sound level meters, modular measuring systems, etc. This fact is remarkable when looking at microphones, main item of any acoustics measuring chain. The microphones used in almost all the noise dosimeters are not standardized despite the common sense that to assure measurement reliability, microphones should meet international manufacturing and testing standards. The present noise-dosimeter standards are not conclusive about the right acoustic field to which microphones for this task should be constructed. For those reasons, the frequency response on free-field, diffuse-field and pressure-field of a population of noise dosimeter's microphones of a worldly well-known brand will be determined and compared to present applicable international standards to evaluate the actual reliability of the measures produced by this kind of equipment.
Full Paper
Realization of Air-borne Sound pressure unit with LDA technique by Spectrum and autocorrelation method in a travelling wave tube
He, Longbiao (1), Feng, Xiujuan (1), Yang, Ping (1), Niu, Feng (1), Zhong, Bo (1)
(1) National Institute of Metrology, China
ABSTRACT
To realize the sound pressure unit directly, the method of sound pressure measurement based on acoustic particle velocity with LDA technique was described. In order to get a simple acoustic field, a travelling wave tube was designed. The sound pressure distribution obtained by microphone along the tube was measured. The result showed the acoustic field inside the tube could be considered as travelling wave. The air-borne sound pressure is equal to the product of the air density, sound speed and the particle velocity. The laser Doppler Anemometry was used to measure the particle velocity in the acoustic field. The modulated doppler signal was obtained by TSI laser doppler system and the doppler signal was processed by autocorrelation method and spectrum analysis method. With the spectral analysis of doppler signal, the particle vibration velocity was obtained with the Bessel function analysis and the velocity can also be calculated based on the time of characteristic values of the correlation function. The comparison of sound pressure measured by microphone and the value deduced from the velocity measured by laser Doppler system shows that they have good agreement and the deviation is less than 0.5 dB.
Full Paper
Influence of ground-shield configuration in reciprocity calibration of laboratory standard microphones
Olsen, Erling Sandermann (1), Carlsen, Henrik (1)
(1) Brüel & Kjær, Denmark
ABSTRACT
The open-circuit sensitivity of condenser microphones, and in particular Laboratory Standard (LS) and Working Standard (WS) microphones, depend on the mechanical ground-shield configuration of the preamplifier. Therefore, the mechanical ground-shield configurations of preamplifiers for LS and WS microphones are defined in the IEC 61094 standard series. The sensitivity, dynamic range and acoustic impedance of the microphone loaded by a preamplifier also depend on the electrical configuration of the shield and the preamplifier's input impedance. Minimizing the load on the microphone is generally preferable. This is achieved with "driven" shield where the shield is driven with the microphone output signal. Recently, it has been shown that adaptors used for free-field reciprocity calibration of WS3 microphones with the driven shield configuration may present a too high load to the preamplifier type traditionally used. In this paper, it is showed that a simple modification of the preamplifier can eliminate this problem, even for adaptors that present a rather extreme load to the preamplifier. The ground-shield configuration and the electrical configuration of the shield is discussed, both in the case of ideal and non-ideal electrical conditions, and in the context of reciprocity calibration of microphones and the 61094 standard series.
Full Paper
On the reduction of the engine and aerodynamic noise of aircraft
Campos, L M B C
Técnico, U.Lisboa, Portugal
ABSTRACT
Air traffic is growing at a steady rate of to 7% per year in most regions of the world, implying a doubling every 10-25 years. This requires major advances in aircraft noise reduction at airports, just not to increase the noise exposure due to the increased number of aircraft movements. In fact it can be expected, as a consequence of increased opposition to noise by near airport residents, that the overall noise exposure will have to be reduced by bans, curfews, fines, and other means and limitations, unless significantly quieter aircraft operations are achieved. The ultimate solution is aircraft operations inaudible outside the airport perimeter, or noise levels below road traffic and other existing local noise sources. These substantial noise reductions cannot come at the expense of a degradation of cruise efficiency, that would affect not just economics and travel time, but would increase fuel consumption and emission of pollutants on a global scale. The paper reviews the: (i) current knowledge of the aircraft noise sources; (ii) the sound propagation in the atmosphere and ground effects that determine the noise annoyance of near-airport residents; (iii) the noise mitigation measures that can be applied to current and future aircraft; (iv) the prospects of evolutionary and novel aircraft designs towards quieter aircraft in the near term and eventually to operations inaudible outside the airport perimeter.
Full Paper
Benchmark study of numerical solvers for the prediction of interior noise transmission excited by A-pillar vortex
Cho, Munhwan (1), Kim, Hyoung Gun (1), Oh, Chisung (1), Ih, Kang Duck (1), Khondge, Ashok (2), Mendonça, Fred (3), Lim, Jongyun (4), Choi, Eui-Sung (5), Ganty, Bastien (6), Hallez, Raphael (7)
(1) Hyundai Motor Group, South Korea
(2) ANSYS Inc., India
(3) CD-adapco, UK
(4) ESI Korea, South Korea
(5) Exa Korea Inc., South Korea
(6) Free Field Technology, Belgium
(7) Siemens PLM, Belgium
ABSTRACT
Wind noise in road vehicles is being made much quieter to satisfy customers' demands for comfortable driving environments. The interaction between outside flows and exterior surfaces at the front and sides of a vehicle forms a strong swirling fluid structure called A-pillar vortex which is one of the most crucial wind noise sources. The geometrical characteristics of the A-pillar can determine the size or strength of the vortex structure. It is tremendously time-intensive and costly to change the shape of the A-pillar if it cannot be modified in the early development stage. For early determination of its shape, a reliable numerical methodology to predict vehicle interior noise due to the A-pillar vortex should be applied. This can be very challenging because the numerical method should simulate the complicated fluid behaviors as noise sources and the structural motions acting as transmission and propagation paths with acceptable precision. In this study, various numerical solvers are validated as the predictive tool of the interior transmitted noise in a simplified vehicle model. The solvers examined in the open benchmark study use various computational fluid and vibro-acoustic methods. It is shown that most of the software has prediction ability enough to industrial purposes.
Full Paper
Characteristics of turbulent noise from backward-curved centrifugal fan with rectangular casing
Hayashi, Hidechito (1), Aramaki, Takuma (2), Shirahama, Seiji (2), Oda, Ippei (2), Okumura, Tetsuya (1)
(1) Nagasaki University, Japan
(2) Panasonic Ecology Systems Co, Japan
ABSTRACT
The backward-curved centrifugal fan with rectangular casing is used to the air conditioners and the air cleaners that is required the compact and flexible design. We have studied the fan with rectangular casing by experiments and numerical simulation. It is pointed out that the performance of the fan with the rectangular casing is better than that with scroll casing at the large flow rate. The turbulent noise consists of the three frequency ranges, low frequency range under 800Hz, middle frequency range 1200-2700Hz and high frequency range 2700-4000Hz, that have the different noise source. The low frequency range is generated from the impeller, the middle frequency range is mainly generated from the casing wall and the high frequency range is in relating to the flow above the shroud. The secondary flow near the shroud causes the large turbulence and generates the high frequency and large turbulent noise. We proposed the obstacle to reduce the noise level, and then the noise level of high frequency is reduced about 5 dB.
Full Paper
Characterization of an Aeroacoustic Wind Tunnel Facility
Pascioni, Kyle (1), Reger, Robert (1), Edstrand, Adam (1), Cattafesta, Louis (1)
(1) Florida State University, USA
ABSTRACT
The Florida State Aeroacoustic Tunnel (FSAT) is an open-circuit anechoic wind tunnel designed for low subsonic aerodynamic noise studies. Nominal flow speeds in the test section range from 5-75 m/s and are achieved using a 450-hp centrifugal blower. The test section, with dimensions 0.914× 1.219×3.048 m (H×W×L), can take the form of an open-jet or closed-wall configuration. A 250 Hz anechoic chamber (2.7×4.5×4.8 m) surrounds the test section. Flow non-uniformity and turbulence intensity are measured to be <1% and <0.12%, respectively, for both test section configurations at all flow speeds. To enhance acoustic quality, an inlet silencer is placed upstream at the entrance of the tunnel, while a metal perforate liner is used over the entire length of the diffuser. Additionally, a swiveling jet collector rotates ±10 degrees for lifting bodies that deflect the freestream jet. Depending on frequency, background noise levels are found to scale with Mach number between the fifth and eighth power, and are 80 dBA at Mach 0.17. The major noise sources are determined to be the first set of turning vanes, jet collector, and the fan/motor. Reduction techniques of these noise sources are proposed and will be considered in future work.
Full Paper
Common failings of inter-disciplinary studies on noise and the potential solutions
McLaren, Stuart J (1), Page, Wyatt H (1)
(1) Massey University, New Zealand
ABSTRACT
Inter-disciplinary research has been published on the adverse effects of noise in health, education and other areas. These studies often produce findings that on close examination are ambiguous; display flawed methodology and conclusions not supported by the measurements. This paper highlights common anomalies and errors in noise assessment which have passed through the peer-review process to publication in journals. Often ambiguity in the findings is the result of using incorrect notation and terminology, combined with a poor understanding of appropriate noise descriptors. It is common practice to perform the statistical analysis on the sound levels in decibels. But this leads to an underestimation of the effect because adverse health effects of noise typically display a dose response to the product of the sound pressure squared and time. Methodologies are often described without reference to best practice or existing standards that typically describe in detail robust measurement procedures. There is a need to educate researchers involved in noise studies about the need for competency in noise measurement and assessment. It also highlights to journal editorial staff about the need to include in their peer review process someone with appropriate expertise in noise.
Full Paper
Web-based calculators for transportation noise and vibration
Smith, Michael (1), Chiles, Stephen (2)
(1) URS, New Zealand
(2) NZ Transport Agency, New Zealand
ABSTRACT
The NZ Transport Agency has developed a number of on-line calculators for road-traffic noise and construction noise and vibration. These tools allow members of the public, project managers, and contractors to perform calculations that would typically be the domain of an acoustics specialist. The calculators use recognised methods (CRTN, BS 5228) applying the simplifications necessary for a 2-dimensional model. This paper discusses the benefits of empowering non-specialists to perform acoustical calculations, as well as identifying where oversimplification can lead to invalid conclusions. The New Zealand implementation will be presented as a case study, providing lessons learnt from the five years of development.
Full Paper
Post baccalaureate professional development in noise control engineering
Holger, David K
Iowa State University, USA
ABSTRACT
Professional development opportunities for practicing engineers are an important element of noise control engineering education. An effective and efficient approach to providing these opportunities involves leveraging development and delivery of formal professional master's programs, graduate certificates, formal coursework, and non-credit workshops and short courses. Typical audiences for these offerings include practicing engineers with substantial undergraduate background in noise control engineering, practicing engineers who lack fundamental background in noise control engineering, and other professionals who need background information on noise control engineering because of their related work in consulting, government, or management roles. Courses and other programmatic elements can be developed to utilize educational technology, simulations, and distance delivery via the internet to a variety of audiences including on-campus students, off-campus students, and students who receive materials via multiple modes. Leveraging the development of various elements enables efficient and cost effective delivery of educational programs to the often small and specialized interest audiences
Full Paper
Extending the scope of urban sound planning by education and research
Scheuren, Joachim (1), Kropp, Wolfgang (2), Forssen, Jens (2)
(1) Müller-BBM, Germany
(2) Chalmers University of Gothenburg, Sweden
ABSTRACT
Based on continuous research work as well as on growing demands of all involved it is widely agreed today that acoustic comfort in cities should aim for more than just preventing and controlling given noise. However, in practice this typically fails because of two dilemmas: Acoustical aspects are considered too late and with a limited scope only, limited to make other non-acoustic planning acoustically acceptable. This then prevents any approaches to plan and go for desired sound scenarios from being applied.
The European Integrated Training Network SONORUS tries to overcome this restriction by application oriented research, exemplary application to test sites and - above all - by education. Nine partners from all over Europe, coordinated by Chalmers University of Gothenburg, work together to educate 14 young re- searchers in urban sound planning. Apart from complementing available tools for practical application and testing these tools in case studies provided by five associated European cities, the basic idea of the project is to supply the researchers with all skills enabling them to acoustically contribute with competence to a holistic urban planning process. It is hoped that the concrete availability of their respective competence will help to extend the scope of Urban Sound planning in practice.
Full Paper
Expanding the horizon of machinery noise source control via a dedicated short course on gear dynamics and noise
Singh, Rajendra
Ohio State University, USA
ABSTRACT
The dedicated 4-day short course on gear dynamics and noise (taught by the author and his colleague Donald Houser) is intended for designers and engineers involved in the analysis, manufacture, design specification, or utilization of gear systems. Over the past 35 years more than 1800 engineers from over 355 companies around the world have attended this short course. Industries that have found this course helpful include the automotive, transportation, wind-energy, process machinery, aircraft, appliance, and general manufacturing. The course covers the fundamentals of gearing kinematics, gear dynamics, source mechanisms governing major gear whine and rattle noise problems, structural paths with focus on bearings, noise and vibration measurements and diagnostics. A popular feature of this course is the interspersing of demonstrations with lectures; this makes the course appealing to both gear designers and noise (or measurement) specialists. Yet another novel approach is the workshop on "real life" gear noise and dynamics problems. This workshop allows the instructors and participants to interact and discuss case histories presented by attendees. A round table discussion on the last day is utilized to foster interactive problem solving, modeling and measurement discussions. Finally, issues posed by attendees have led to fundamental studies and graduate theses.
Full Paper
Use of traffic modeling and geographic information systems to evaluate noise reduction policies in urban environments: case study in Bogota - Colombia
Paez, Daniel (1), Caviedes, Alvaro (1)
(1) Uniandes, Colombia
ABSTRACT
In order to support policy development and evaluation at Los Andes University in Colombia we developed the Bogota Geographic Noise Model (BGNM). This model, based on a transport model and a geographic information system, estimates sound pressures caused by transportation. The model determines areas of the city where legal limits for noise levels are exceeded. Using the BGNM it was found that over 90% of important facilities in Bogotá, such as schools and hospitals, do not have an acceptable noise quality according to current local regulations. In order to address this problem, reducing speed limits and restricting heavy vehicle traffic in the vicinity of key hospitals is being considered. In this paper we present results from further developments to the BGNM in order to evaluate, in 5 specific locations, the proposed traffic measures. To achieve this the further development of the model included additional capabilities to consider a 3D city (building heights and terrain elevation) as well as a traffic-modeling module. Results from this investigation suggest that the new capabilities of BGNM allow better understanding of noise conditions and a more effective and efficient way to develop scenarios.
Full Paper
Assessment of noise pollution sourced from entertainment places in Antalya, Turkey
Sari, Deniz (1), Ozkurt, Nesimi (1), Hamamci, Samet Feyyaz (1), Ece, Mustafa (2), Yalcindag, Nazli (2), Akdag, Ali (3), Akdag, Nese (4)
(1) Environment and Cleaner Production Institute, Turkey
(2) Antalya Metropolitan Municipality, Turkey
(3) HIDROTEK Engineering Co.Ltd., Turkey
(4) Yıldız Technical University, Turkey
ABSTRACT
Noise pollution with the increased entertainment facilities especially in the touristic cities, has been turned out to be one of the major problems that impact the quality of life all over the world. Antalya is the most prominent tourism center in Turkey with its historical places, beaches and crowded entertainment areas. Entertainment life in Antalya is more dynamic and versatile than an usual touristic city with beaches parties, hotel discos, wedding ceremonies and night clubs. Emphasis in this paper is placed on conducting computer simulation using the SoundPLAN 7.3 to assess the noise exposure levels sourced by above 600 entertainment facilities such as discos, bars and pubs etc. in the city center of Antalya. The levels of entertainment noise exposure in the city was calculated according to the European Noise Directive. Almost all of the entertainment places located at the sea side, therefore the most affected population from the entertainment noise live close to these regions. Our results show that nearly 29,000 households during daytime and 10,500 households at night-time were exposed to 50 dB(A) or higher entertainment noises in Antalya. In other words, 3% of the resident population is potentially threatened by high noise levels which may cause to several illness such as hypertension, sleep disturbances etc.
Full Paper
Implementation aspects of the Boundary Element Method including viscous and thermal losses
Cutanda Henriquez, Vicente (1), Juhl, Peter (1)
(1) University of Southern Denmark, Denmark
ABSTRACT
The implementation of viscous and thermal losses using the Boundary Element Method (BEM) is based on the Kirchhoff's dispersion relation and has been tested in previous work using analytical test cases and comparison with measurements. Numerical methods that can simulate sound fields in fluids including losses are particularly interesting whenever small cavities and narrow passages are present, as is the case with many acoustic devices such as transducers and small audio appliances. The present paper describes current work aimed at improving the method by addressing some specific issues related with mesh definition, geometrical singularities and treatment of closed cavities. These issues are specific of the BEM with losses. Using examples, some strategies are presented that can alleviate shortcomings and improve performance.
Full Paper
Prediction of the radiated sound power from a fluid-loaded finite cylinder using the surface contribution method
Liu, Daipei (1), Peters, Herwig (1), Kessissoglou, Nicole (1), Marburg, Steffen (2)
(1) UNSW Australia, Australia
(2) Universität der Bundeswehr München, Germany
ABSTRACT
Based on acoustic radiation modes, the surface contribution method has been developed to predict the surface contributions to the radiated sound power from a vibrating structure. In this work, the surface contribution method is used to identify the sound field on a vibrating structure submerged in a heavy fluid. It was recently found that surface contribution method was not able to predict the surface contributions at low frequencies when the structural wavenumber is higher than the acoustic wavenumber. In this paper, the acoustic radiation efficiencies calculated for different numbers of integration points are compared and used to compute the surface contributions to the radiated sound power. The radiated sound power obtained from both the surface contribution and the active intensity methods are compared. Numerical results for a fully coupled finite element/boundary element model of a cylindrical shell with hemispherical end closures submerged in water show that the surface contribution method can also be successfully applied at low frequencies.
Full Paper
A review of the coupling parameter of the Burton and Miller boundary element method
Marburg, Steffen
UniBw, Germany
ABSTRACT
The phenomenon of irregular frequencies or spurious modes in boundary element techniques for acoustic problems has been well investigated and a number of methods have been presented to overcome this problem. The most popular methods seem to be the Combined Helmholtz Integral Equation Formulation (CHIEF) and the Burton and Miller formulation. This contribution deals with the latter and its only parameter, i.e. the so-called coupling parameter. It is known for more than four decades that this parameter must be complex for radiation from rigid bodies with particle velocity prescribed. During the 1980ies, a number of authors proposed the value of i/k. This value is proving to be an excellent choice for the high frequency limit. However, it turned out that the optimal choice of the coupling parameter depends on a few more parameters including the harmonic time dependence and the formulation of the integral equation itself. This paper discusses these influences for a specific EAA benchmark case which has only recently been proposed, i.e. the radiatterer.
Full Paper
A comparison of numerical methods for the large-scale modelling of acoustic coupled fluid-structure interactions of double-walled cylindrical shells
Peters, Herwig (1), Wilkes, Daniel Ryan (2)
(1) UNSW Australia, Australia
(2) Curtin University, Australia
ABSTRACT
This paper presents a comparison of numerical methods used to model large scale acoustic coupled fluid- structure interaction (FSI) problems for single and double-walled cylindrical shells. The finite element method (FEM) is used to model the structure while the fast multipole boundary element method (FMBEM) is used to model the fluid domain and both models are coupled on the shared boundary surface to allow for the FSI, yielding a coupled FEM-FMBEM formulation. At suitably high frequencies the statistical energy analysis (SEA) method may instead be used to model both the complete fluid domain and the structure. The FEM- FMBEM and SEA models are compared for two structural configurations. The first involves a single-walled cylindrical shell while the second case involves a double-walled cylindrical shell, where two cylindrical shells of different radii encapsulate an interior body of water. The SEA model is seen to provide substantially faster solution times at high frequencies, while yielding similar results to the FEM-FMBEM model.
Full Paper
Minimising the cost of noise control in the coal seam gas industry by selection of noise treatments for gas wells using engineering optimisation
Davis, David James
URS, Australia
ABSTRACT
Reducing costs is an important consideration when designing gas field facilities. The cost of noise mitigation treatments to the power units and pumps at well-heads can be a significant proportion of capital expenditure, and opportunities to reduce these costs are usually welcomed. The assessment and management of environmental noise impact from land-based gas fields is somewhat unique because of the large number of noise sources distributed over a very large area, often with many noise receptors interspersed between the wells and with most receptors receiving noise simultaneously from many wells from different directions. With such complexity, it can be difficult to select and design noise control treatment for the noise sources located at the wells in a cost-effective manner. It would be advantageous to have a calculation tool that could select appropriate noise treatments for each noise source at each well so that the environmental noise targets are achieved at each receptor while simultaneously ensuring that the cost-effectiveness of the noise mitigation program is maximised. This paper demonstrates an example of using three different optimisation techniques to minimise the cost of the overall noise control treatment scheme for the major noise sources located at coal seam gas wells.
Full Paper
Acoustic and Vibration Stability Analysis of Furnace System in Supercritical Boiler
Kwon, Hyuk-Min (1), Cho, Chi-Hoon (1), Kim, Heui-Won (1)
(1) Hyundai Heavy Industries Co., South Korea
ABSTRACT
The furnace of supercritical boiler is tall and flexible because it consists of thousands of tubes connected with thin plates each other. So the furnace has additional outfitting structure to resist internal combustion turbulent flow, external wind load and earthquake forces. It is difficult to evaluate the dynamic characteristics of the furnace in the design stage due to structure complexity. The evaluation procedure for dynamic characteristics of the furnace was proposed in this paper based on CFD, acoustic resonance calculation and transient forced vibration analysis considering the temperature change of furnace inside. The transient CFD analysis of the furnace combustion has been carried out to obtain the fluctuating pressure which was good agreement with acoustic mode of the furnace. The transient forced vibration analysis has been performed considering combustion fluctuation pressure, which was evaluated with allowable vibration limit. The proposed evaluation procedure has been applied to HHI's supercritical power plant project.
Full Paper
Noise Control for Fluid Power Systems
Li, Binghui (1), Moore, Simon (2)
(1) SLR Consulting Australia Pty Ltd, Australia
(2) AECOM Australia Pty Ltd, Australia
ABSTRACT
Pressure pulsation, created by the operation of hydraulic pumps in a fluid power system, is one of the primary causes of noise issues from hydraulic machinery. The wave energy resulting from such pulsation propagates in both the wall and the fluid of the flow pipes associated with the fluid power systems, inducing fluidborne vibration of the pipes and the consequent noise radiated from the pipes. The pressure pulsation can be controlled using many available techniques, including the design of quiet fluid power pumps, active control (e.g. by implementing fluid wave actuators) and passive control treatments (e.g. by installing pulsation suppressor/dampener). This paper presents a case study of noise control for a series of marine hydraulic mooring winch systems installed on a marine barge, which emit excessive noise levels during operation. The installation of passive pulsation suppressors was proposed as the most practical solution to control pulsation from the fluid power units and the consequent excessive noise radiation from the flow pipes, considering a number of factors such as cost, implementation schedule and complexity, as well as intrusion to the system.
Full Paper
The challenge of meeting both acoustic and thermal comfort in 21st century school classrooms
Campbell, Colin (1), Svensson, Carsten (1), Nilsson, Erling (1)
(1) Saint-Gobain Ecophon AB, Sweden
ABSTRACT
The benefits of "thermal mass" in stabilizing temperature for thermal comfort and reducing building energy consumption for sustainable green buildings are well documented. However, when exposing the concrete soffit for thermal purposes it is then not possible to have a fully covered sound absorbing suspended ceiling in classrooms for acoustic comfort. In turn, this potentially compromises the achievement of good acoustic comfort while still utilizing the thermal mass of the exposed soffit. For this paper we measured a classroom configuration with free hanging sound absorbing units and wall absorbers instead of a fully covering traditional suspended ceiling. We looked into solving the low frequency imbalance - a potential negative consequence of not having a full suspended ceiling - with an enclosed void which can trap the low frequency sound (125Hz) which can build up and interfere with the important speech frequencies. We looked at the challenge of optimizing the acoustic coverage range without affecting the thermal comfort. We also wanted to improve the balance of the potentially negative low frequencies to achieve good speech communication and acoustic comfort for all students and teachers, while also providing an inclusive acoustic environment for sensitive listeners.
Full Paper
Noise associated with the ground water systems serving residential geothermal heat pumps
Fullerton, Jeffrey L
Acentech, USA
ABSTRACT
Geothermal heat pumps are an energy efficient option for many residences as an alternative to more conventional gas or oil fueled residential HVAC systems. This paper continues discussions about the noise and vibration issues from these residential geothermal systems that have been presented in prior papers by this author. In this paper, the noise contributions of two components of the ground water system will be discussed. First, the paper will discuss the influence of noise from the control system that regulates the ground water flow. A comparison of the noises from a simple pressure switch system versus a variable speed controller will be discussed. Second, the ground water system includes zone control valves to manage the water flow for the different systems. These valves can contribute to the noise generated by the system when it operates. Two types of valves will be discussed, which have dramatically different designs and different sound emissions. The paper concludes with recommendations for achieving a low noise ground water system to serve the geothermal heat pumps.
Full Paper
Acoustical investigation of open-plan offices in green building: Simulation experiment
Nazli, Che Din (1), Nurul Amira, Abd Jalil (1), Nila Inangda, Keumala (1), Asrul Sani, Razak (1)
(1) University of Malaya, Malaysia
ABSTRACT
The authors have previously reported on the measurement results from the investigation and evaluation done on the acoustical performance of open-plan offices in green buildings in Malaysia. This research uses the results from field measurements for verification on the optimum modeling process for two existing open-plan office in term of calculation time and accuracy of the simulation. Two models of open-plan office layout were constructed in four different level of model detailing utilizing 3D modeling tool. Using ODEON Room Acoustic Simulation Software, the authors examined the effects of the geometrical properties to identify the appropriate model setting for further simulation process. The simulated results of two acoustical parameters; reverberation time (RT) and speech transmission index (STI) for each model setup are then compared between each other, and further compared with field measurement results. The study concludes that the modeling process in term of number of surfaces is affecting the acoustical parameters. The discrepancy of simulated RT and STI data between model setup will be discussed.
Full Paper
Room impulse response measurement with a spherical microphone array, application to room and building acoustics
Barré, Sébastian (1), Döbler, Dirk (1), Meyer, Andy (1)
(1) GFaI e.V., Germany
ABSTRACT
Room impulse response measurement using deterministic signals like sine sweeps is a well-established method to obtain objective parameters that describe the acoustic field in 3-dimensional space. Combined with conventional delay-and-sum beamforming, it becomes a very powerful tool offering precise information about the behaviour of acoustic waves inside or between rooms. More precisely, the use of a transparent array allows us to process the microphone's signals directly by spectral division, a linear deconvolution method, and to analyze the resulting room impulse responses through beamforming. This permits a precise localization of the direct sound and the early reflections over time and space. Additionally, the high signal-to-noise ratio and decorrelation properties offered by the method permit to highlight leakage and airborne sound transmission paths between rooms. Finally, the repeatability of the method allows for a comparison of measurements of various room configurations, for example in the case of acoustic treatment and optimization.
Full Paper
Sound source localization accuracy of ambisonic microphone in anechoic conditions
Malecki, Pawel
AGH University of Science and Technology in Krakow, Poland
ABSTRACT
The paper presents results of determination of sound source localization based on signals measured by first-order ambisonic microphone. The experiment consisted in recording the test signals with the 3D microphone positioned in the axis of the turntable in the anechoic chamber. The spherical coordinates of the sound intensity vector were calculated and compared to actual values resulting from the geometry of the system. Accuracy of the localization of the sound source depending on the frequencies, the time constant and the parameters of the signal recording was presented. The obtained results show the effectiveness of the sound source localization using first order ambisonic microphone in laboratory conditions.
Full Paper
Influence of time-varying talker directivity on the calculation of speech transmission index from speech in a room acoustical context
Opsata, Adam (1), Cabrera, Densil (1), Yadav, Manuj (1)
(1) University of Sydney, Australia
ABSTRACT
Standard calculations of the Speech Transmission Index (STI) are most frequently determined using specialised test signals, but methods have also been developed that estimate an STI value by using real speech as the stimulus signal. However, these methods have previously been studied in highly controlled scenarios, and have rarely been tested using real human talkers in real acoustical environments. We conducted a test to study how the natural movements of real talkers within an actual room environment affects the calculation of speech-based STI, by comparing results to those produced by a stationary head and torso simulator. In addition to the challenge of analysing a non-ideally modulated test signal, using a human talker introduces time variance in the transfer function from reference microphone to receiving microphone (due to incidental body movements and time-varying directivity). This paper examines the extent of this effect using a 130 m3 room with long and short reverberation times.
Full Paper
Validation of lateral fraction results in room acoustic measurements
Protheroe, Daniel (1), Day, Christopher (1)
(1) Marshall Day Acoustics, New Zealand
ABSTRACT
The early lateral energy fraction (LF) is one of the most important acoustic descriptors of concert hall sound. This paper describes a procedure for validating LF measurements of halls. The measurement of LF can be problematic due to uncertainties with calibrating, aligning and aiming two microphones of different sensitivities and directivity patterns. The validity and reproducibility of measured LF values needs to be established. A series of simulated sound fields consisting of the direct sound and a single reflection in an anechoic chamber were used to validate LF measurement systems. The reflection was varied in angle and level, and the measured LF values were compared with the known or calculated values. Two commercially available measurement systems were validated and the measured results were generally within one JND of the calculated values.
Full Paper
Study on the vertical vibration of an occupant - seat cushion system
Hou, Zhichao
Tsinghua University, China
ABSTRACT
Dynamic interaction between a human body and the seat cushion was addressed, aiming at seat design for better NVH performance of a passenger vehicle. Referring to DIN EN ISO 3386-1 and previously researches, static and dynamic tests were conducted on polyurethane foams typically used as vehicle seat cushions. A one-dimensional stress strain relation was derived based on the measured data, in which the nonlinear elastic behavior of the foam material is regarded as piecewise linear in terms of the static strain while the viscoelastic property is described using a fractional derivative. A model was then established with some simplification to reflect the interaction in the vertical direction between a foam cushion and a seated occupant, where the seated human body was depicted by a lumped parameter model. Apparent mass of the system was calculated using the model, which were validated by experiments with or without seat cushion. The influence of the foam cushion is thus demonstrated on the vertical vibration of the occupant, which will be helpful to vehicle seat design.
Full Paper
Development of an adaptive composite leaf spring
John, Sebastian (1), Dannemann, Martin (1), Kostka, Pawel (1), Ehlig, Jana (1), Modler, Niels (1)
(1) TU Dresden, Germany
ABSTRACT
As suspension of vehicles is generally designed for maximum load, its driving performance for light loaded cases is poor. Additionally, a hard suspension leads to dynamic peak loads on the vehicle structure and freight resulting in an increased noise level. Hence especially in trucks adjustable pneumatically driven suspension systems are commonly used. However, these systems are high maintenance and expensive compared to classic metallic leaf springs. Within the research of the collaborative research centre (SFB) 639 an innovative adaptive lightweight suspension system consisting of glass fibre-reinforced polypropylene (GF/PP) leaf spring elements is designed. Via a component integrated hydraulic system different levels of stiffness can be applied to the spring element depending on the loaded mass and road properties in order to reduce accelerations of the load platform and vibration peaks of the freight. Especially when transporting loose freight a reduction of mass acceleration is a basic possibility to reduce noise emission. Through a detailed multi-body simulation of a demonstrator vehicle, reduced amplitudes of platform acceleration and dynamic wheel loads were determined when using the novel suspension system. Considering multiple operation conditions, the ascertained results indicate a significant reduction of noise emission.
Full Paper
Measurement of the distributed dynamic stiffness of seats under compression to analyze dynamic characteristic of seats
Kim, Deokman (1), Min, Kyongwon (1), Park, Hyunkyu (2), Park, Junhong (1)
(1) Hanyang University, South Korea
(2) Hyundai•Kia Motors, South Korea
ABSTRACT
Supporting stiffness of seats is an important component affecting dynamic characteristics cognized by a passenger. To analyze dynamic characteristic of a seat for vehicles operating on various road conditions, the seat vibration from road irregularity should be understood and compared. In this study, the seat is analyzed as distributed supporting system. The dynamic stiffness is measured using masses on elastic foundation. The deflection of the seat under compression is analyzed using simple numerical model and used in understanding dynamic coupling between arrayed masses. The characteristic of the seats is analyzed by measuring distributed dynamic stiffness. The influence of seat cover, elastic support and flexible polyurethane foam on the measured stiffness was analyzed. The equivalent dynamic stiffness when larger dummy model is used in measurements is compared to the distributed stiffnesses
Full Paper
Tire/road contact modeling for the in-vehicle noise prediction
Vuj, Trong Dai (1), Yin, Hai Ping (2), Duhamel, Denis (2), Gaudin, Arnaud (3), Abbadi, Zouhir (3)
(1) ENPC, France, PSA, France
(2) ENPC, France
(3) PSA, France
ABSTRACT
A numerical model for the contact between a wheel-air-tire system and a road surface is presented. The forces calculated at the center of wheel are to be used in a full numerical model of a vehicle for the in-vehicle noise prediction. The tire/road contact modeling is a difficult task because of the complex structure of the tire and the roughness of the road surface. Two numerical approaches are compared to each other in the present study: the first one solves directly the dynamic equation and the second one uses the static contact force to calculate the vibration of the tire. The numerical results of the forces at the wheel center have been compared to those of measurements conducted by PSA Peugeot Citroe ̈n. The comparison shows good agreement in the low frequency range up to 230Hz.
Full Paper
Structural transfer path analysis of automobile tire/road noise
Yu, Xiongying (1), Pang, Jian (2), Min, Fujiang (1), Wen, Wei (1), Gong, Shichao (3)
(1) Changan Auto Global R&D Center, China, State Key Laboratory of Vehicle NVH and Safety Technology
(2) Changan Auto Global R&D Center, China,State Key Laboratory of Vehicle NVH and Safety Technology
(3) Changan Auto Global R&D Center, State Key Laboratory of Vehicle NVH and Safety Technology
ABSTRACT
With refinement of powertrain, tire/road induced noise has become an important parameter within vehicle development. It is necessary to reveal the transfer characteristics of tire/road noise for suppressing it. This paper presents an experimental analysis of the structural-borne contribution of noise and vibration for a vehicle driving on a coarse road, using a simplified transfer path analysis method (TPA).The simplified TPA method is used to identify the major noise transfer paths of tire/road noise based on subjective evaluation and objective measurement, which is fast and cost-saving compared with conventional TPA method. The vehicle tire/road noise is analyzed by the simplified TPA method, which shows the rear suspensions are the major contribution components. A TPA model for the rear suspension noise and vibration is built up and the transfer path testing is carried out. The comparison of measured and recalculated interior sound pressure level shows a good correlation. The results show Z- direction of the torsion beam axle and Z- direction of the left shock absorber are significant contribution paths to the interior noise. To improve the tire/ road noise and not to sacrifice the side effects such as handling and durability, the torsion beam axle structure is modified.
Full Paper
Project ROSANNE: Rolling resistance, Skid resistance, and Noise Emission measurement standards for road surfaces
Haider, Manfred (1), Conter, Marco (1), Wehr, Reinhard (1), Sandberg, Ulf (2), Anfosso, Fabienne (3)
(1) AIT, Austria
(2) VTI, Sweden
(3) IFSTTAR, France
ABSTRACT
ROSANNE is a collaborative project in the Seventh EU Framework Programme which aims at developing/harmonising measurement methods for skid resistance, noise emission and rolling resistance of road pavements as a preparation for standardization. To achieve this, the project will follow the recommendations of key predecessor projects as well as consider ongoing work in CEN and ISO. The project will develop and improve standards in the field of working group CEN/TC 227/WG 5. For the pavement influence on road traffic noise emission the main objective is to consider the existing measurement methods of SPB (ISO 11819-1) (1) and CPX (ISO/DIS 11819-2) (2) to provide a stable and reliable harmonised method for pavement noise emission properties. The project will validate these methods and a combination of them, incorporate correction mechanisms for temperature influence and investigate its potential use for noise immission calculation methods like the one proposed by the CNOSSOS-EU project (3). It will also explore the potential for recent developments in the measurement of surface texture to deliver parameters that better reflect the physical process of tyre/road interaction and that may improve our understanding of how the texture influences noise emission. The present paper summarizes the project status after the first nine project months.
Full Paper
Effect of road surfaces on road traffic noise on the public roads of Japan - An investigation based on tyre/road noise measurement
Koike, Hiroshi (1), Ito, Akiyoshi (1)
(1) Japan Automobile Research Institute, Japan
ABSTRACT
Tyre/road noise measurements on public roads were conducted in order to investigate the effect of road surface condition on vehicle pass-by noise on public road of Japan. Since applying the CPX method to evaluate public road of Japan must be subject to domestic regulations and is considered to pose some safety risks, a quasi-CPX method was employed after its vehicle noise evaluation validity had been confirmed by road tests on a test track. The tyre/road noise measurements by the method on public roads were performed on 2 routes including 3 types of road surfaces -- dense asphalt (DAC), porous asphalt (PAC), and double layer porous asphalt concrete (DLPAC) surfaces. As a result, it was confirmed that the level of tyre/road noise of each road surface type spreads to the range of 4 to 9dB, and that the spread of DLPAC pavement seems to be wider than other surface types.
Full Paper
SPB and CPX results of rubberized surfaces in the Italian urban and extra-urban context
Licitra, Gaetano (1), Teti, Luca (1), Cerchiai, Mauro (2), Ascari, Elena (3), Chetoni, Marco (1)
(1) I.P.C.F.-C.N.R., Italy
(2) S.A.F. A.V.L.-A.R.P.A.T., Italy
(3) I.D.A.S.C.-C.N.R., Italy
ABSTRACT
Road traffic is the main noise source in urban context and a road surface with low emission characteristics is one of the most applied solutions for noise mitigation actions. Road pavement incorporating rubber (also known as rubberized surface) is a solution often applied all over the world and it has the great environmental benefit of recycling the scrap tires. In Italy the rubberized technologies have been introduced quite recently and some experimental installations have been acoustically studied in the last years. These experimental surfaces have been laid on extra-urban road and exposed to the wear due to the real traffic, in order to verify the time durability of the noise mitigation action too. In this work, data obtained from both Close Proximity method and Statistical Pass-By measurement sessions carried out on some rubberized experimental surfaces are shown. Results show clearly that the rubberized surface can be an efficient mitigation action also in the Italian context. Anyway, in some cases here analyzed the lowering of the emission level was almost negligible and this could be blamed to binding technical skills required by the rubberized surface technology but not perfectly complied during the installation.
Full Paper
A study on comparison of noise reduction effect of single-layer drainage asphalt pavement and double-layer drainage asphalt pavement: Part 2 long-term change of sound power level and frequency characteristic
Ueta, Tomotaka (1), Ishikawa, Kenichi (1), Mori, Hisho (1), Noguchi, Eiji (1), Yoshida, Motoomi (1), Kokusho, Masami (1), Nagaoka, Hironori (1)
(1) Oriental Consultants Co., Japan
ABSTRACT
Using data identical to where described in "Part 1 Sound Power Level and Frequency Characteristics in Initial Construction", The purpose is to study long-term change of sound power level and the frequency characteristic by comparing the single-layer drainage asphalt pavement and double-layer drainage asphalt pavement. It is found that sound power level is calculated, by 6.9log (y+1) [y is equal to years after construction] at light vehicles, 3.0log (y+1) at heavy vehicles. A comparison of initial construction and 70 months after construction for the frequency, A-weighted power spectrum increase uniformly in full range at single-layer drainage asphalt pavement, and increase slightly near the peak frequency at double-layer drainage asphalt pavement. In addition to, equivalent continuous A-weighted sound pressure level of double-layer drainage asphalt pavement is lower than that of single-layer drainage pavement by 2.0-2.5dB.
Full Paper
LDV-based vibration measurement of a stiffened plate covered by a rubber coating with multi-layered periodic porous in air
Huang, Xiuchang (1), Zhu, Dawei (1), Tian, Jin (1), Hua, Hongxing (1)
(1) Shanghai Jiao Tong University, China
ABSTRACT
To control underwater acoustic radiation of ships and protect against detection, coatings are attached to the vibrating wet surface of the hulls. Coatings with different pores or scatterers enclosed will attenuate vibration and suppress sound radiation with different mechanisms. However, there are very few experimental studies concerning vibration measurement of a coated structure in water, mainly due to the water environment. A compromised way to reveal the attenuation mechanism is to measure the vibration in an anechoic chamber. A stiffened plate covered by a rubber coating with multi-layered periodic porous is measured by a LDV scanning system in this study, which is aimed to minimize added mass effect of contact measurement. Comparative measurements on bare stiffened plate and stiffened plate covered with solid rubber are also carried out. Vibration transmission from the stiffened plate to the coatings as well as vibration modes on the radiating surface for the three tested objects is obtained. The vibration and sound attenuation mechanism of the proposed rubber coating is unveiled.
Full Paper
Numerical Study on Non-Cavitating Noise of Marine Propeller
Jang, Ji-Sung (1), Kim, Hyung-Taek (1), Joo, Won-Ho (1)
(1) Hyundai Heavy Industries Co., South Korea
ABSTRACT
Blade Passing Frequency (BPF) noise of a fan or a propeller comprises of the thickness and loading noises. In general, the loading noise is regarded as the main noise source in non-cavitating condition because the thickness noise decreases rapidly with respect to distance from the noise source. In this study, underwater radiated noise for the model scaled propeller is calculated by the rotating dipole formulation coupled with acoustic finite element method which considers the loading noise with reflection surfaces in frequency domain. The CFD analysis is used to calculate blade surface pressures for obtaining the noise source. The wall effect is considered to carry out the noise analysis in the same condition as the water tunnel experiment. The noise predictions are conducted under without and with wake conditions to observe effects of inflow velocity and unsteady loading on the radiated noise, respectively. The both numerical results are in good agreements with experimental results. Based on these results, the prediction method can be used to design a low noise propeller and predict underwater radiated noise including the effect of acoustic reflection by a hull structure.
Full Paper
Optimisation applied to composite marine propeller noise
Mulcahy, N Lex (1), Croaker, Paul (1), McGuckin, Damian G (2), Brandner, Paul A (3), Kessissoglou, Nicole (4)
(1) UNSW, Australia & Pacific ESI, Australia
(2) Pacific ESI, Australia
(3) University of Tasmania, Australia
(4) UNSW, Australia
ABSTRACT
In the design of maritime vessels, the reduction of noise and vibration is of primary importance for the comfort and safety of passengers and crew, the reliable operation of sensitive instruments on research vessels and the acoustic signature of military vessels. One of the main sources of noise and vibration is the propeller. Shape-adaptive structures, which adapt their shape to changes in their operating conditions, have a number of applications including marine propellers. Previous studies of shape-adaptive propellers have concentrated on maximising the efficiency of the propeller, either in a ship's disturbed wake flow or at off-design conditions. In the present work, a method is developed to determine whether propellers with flexible composite blades can be designed to radiate less underwater noise than equivalent rigid propellers. An optimisation procedure, which adjusts the composite material properties in order to minimise the radiated sound, is applied. The core of the procedure is the radiated sound computation, which processes the results of a transient hydroelastic analysis to compute the sound power on a porous surface that surrounds and translates with the propeller. The results of a computation for a flexible propeller are compared to those of a rigid counterpart.
Full Paper
Adulteration of underwater acoustic measurements
Schael, Stefan
WTD 71 Germany
ABSTRACT
The influence of the marine environment caused by radiated sound of ships has become in the focus of research and surveillance programs. Besides the underwater acoustic surveillance measures to control the underwater noise contribution of ships shall be initiated. Identified as a prerequisite, a standard for measurement has to be issued. In a joint working group, within the ISO (International Organization for Standardization) efforts and demands are announced to establish standardization for ship measurements. This paper will describe underwater range facilities in northern Europe owned by the government and operated by the MoD. The experiences depict the difficulties of reproducibility and comparability according to procedures, environmental effects and range equipment.
Full Paper
LES-based Numerical Analysis of Surface-Pressure Fluctuations and Unsteady Thrust of a Marine Propeller
Tian, Jin (1), Yang, Haosen (1), Zhang, Zhenguo (1), Yuan, Guoqing (1), Rao, Zhiqiang (1), Hua, Hongxing (1)
(1) Shanghai Jiao Tong University, China
ABSTRACT
Fluctuating forces induced by a rotating marine propeller are major sources exciting the hull vibration which radiates unwanted underwater noise. To attain a better understanding of the fundamental nature of these excitation sources, a numerical study of blade surface-pressure fluctuations and unsteady thrusts of a marine propeller is performed. A computational model based on large eddy simulation (LES) with moving mesh technique is developed. Considering both of the uniform and non-uniform inflow conditions, the hydrodynamics performances including (i) the spatial variation of the vortex structure; (ii) fluctuating forces acting on the propeller blades; and (iii) the unsteady propeller thrust are obtained in time and frequency domains with reasonable accuracy. The correlation of the vortex structures to pressure fluctuations is evaluated through visualizing the pressure distribution on the blades. The spectral characteristics of the blade surface-pressure and the unsteady thrust are then analyzed and compared for the two different inflow conditions. Numerical results show that clear peak frequencies of the surface-pressure spectrum are related to the harmonics of shaft frequency, and inflow uniformness significantly affects the unsteady thrust spectrum.
Full Paper
Non-specific physical symptoms and related functioning in people with self-reported noise sensitivity
Baliatsas, Christos (1), Van Kamp, Irene (2), Hooiveld, Mariette (3), Yzermans, Joris (3), Lebret, Erik (1)
(1) University Utrecht, The Netherlands, RIVM, The Netherlands
(2) RIVM, The Netherlands
(3) NIVEL, The Netherlands
ABSTRACT
There is not much epidemiological evidence on the symptomatic profile, functional status and illness behavior of people with increased sensitivity to noise. An epidemiological study combining self-administered questionnaires and electronic medical records of non-specific physical symptoms (NSPS) registered by general practitioners (GP) allows such investigation. The study sample consisted of 5933 participants, drawn from 21 practices within the Dutch Primary Care Database. Among participants, 722 (12.5%) responded "absolutely agree" to the statement "I am sensitive to noise". Compared to the rest of the sample, the noise sensitive group reported significantly higher scores on number and duration of self-reported NSPS and indicators of functional impairment and illness behavior. There was also a higher prevalence of GP-registered NSPS among noise sensitive respondents. Results remained consistent after adjustment for demographic characteristics and GP-registered morbidity. Noise sensitivity was strongly associated with various other sensitivities such as those to chemical substances, odors and electromagnetic fields. Individuals with high levels of noise sensitivity share characteristics similar to those of people with other self-reported sensitivities. These findings add to the notion that different types of sensitivities might share a common (psycho) physiological basis.
Full Paper
What factors are associated with noise sensitivity in the UK population?
Clark, Charlotte (1), Smuk, Mel (1), Stansfeld, Stephen (1), Van De Kerckhove, Rik (2), Notley, Hilary (2)
(1) Queen Mary University of London, UK
(2) Defra, United Kingdom
ABSTRACT
This paper explores whether certain sub-groups of the UK population are more or less noise sensitive, using the 2012 National Noise Attitude Survey (NNAS 2012) dataset. NNAS 2012 was a community questionnaire survey of 2747 respondents in the UK, which measured attitudes to environmental noise. Data relating to a range of sociodemographic, dwelling, and geographic factors was also collected. Respondents rated how sensitive they were to noise on a seven-point scale ranging from 'not at all sensitive' to 'very sensitive'. Linear effect coding regression analyses were used to develop multivariable models of associations with noise sensitivity. A range of noise sensitivities were reported by the respondents (median = 4). Overall, noise sensitivity was more strongly associated with sociodemographic factors than with dwelling or geographic factors. Age; gender, homeownership, children, employment status, social class, and interviewer rating of hearing problems were associated with noise sensitivity after adjustment for dwelling and geographic factors. The analyses suggest that certain sub-groups of the population may be more or less noise sensitive compared with the UK population as a whole. The policy implications of these findings will be discussed.
Full Paper
Influence of visual factors on noise annoyance evaluation caused by road traffic noise in indoor environment
Ma, Hui (1), Nie, Wenjing (1)
(1) Tianjin University, China
ABSTRACT
Through laboratory experiments the variation of noise annoyance caused by road traffic noise with LAeq.20sec of 35, 45, 55 and 65dB under different visual conditions in study and living rooms was explored. The experimental result shows that in the indoor environment the influence of brightness perception on noise annoyance caused by road traffic noise was more obvious, and the effect of color perception on noise annoyance evaluation was not significant though color and brightness had an interaction effect on noise annoyance evaluation. Therefore, both improving the lighting conditions and creating a reasonable combination of color and brightness condition was helpful for the noise control in the indoor environment.
Full Paper
Prediction method of insertion loss of detached houses against road traffic noise based on a point sound source model- Prediction formula considering the heights of buildings and a prediction point
Fujimoto, Kazutoshi (1), Tominaga, Toru (1), Morita, Kengo (1), Hirata, Tomoko (1)
(1) Kyushu University, Japan
ABSTRACT
In the Environmental Quality Standards for Noise in Japan (EQS) revised in 1998, the problem of environmental noise at areas facing roads is evaluated by obtaining the numbers and the rates of buildings at which noise levels exceed the standard value. The Standards allow for the estimation of noise levels, instead of requiring actual measurements, in cases where taking the actual measurements would be difficult. In order to estimate noise levels, to grasp insertion loss of buildings in an evaluated area is needed. Based on the above background, the authors proposed F2012a which can predict insertion loss of detached houses against road traffic noise based on a point sound source model. However, F2012a confines the heights of buildings and a prediction point to 10m and 1.2m above the ground, respectively. To expand these heights, this paper propose an extension formula of F2012 which can be applied to the condition when the height of buildings is less than 10m and a prediction point is lower than buildings. The validity of the proposed formula is verified through the experiments. This extended F2012 is adapted into ASJ RTN-Model 2013, a new version of ASJ RTN-Model, and applicable to the evaluation of EQS.
Full Paper
Numerical analysis of sound insulation performance of double-layer wall with vibration absorbers using FDTD method
Lin, Shuo-Yen (1), Shinichi, Sakamoto (2)
(1) Graduate School, the University of Tokyo
(2) Institute of Industrial Science, the University of Tokyo
ABSTRACT
For investigating the detail effects of the vibration absorbers in the cavity of the double-layer wall (DLW), a vibro-acoustic numerical model was developed and the behavior of the system was simulated by the finite-difference time-domain method (FDTD method). By comparing the results for various cases, the mechanism of the vibration absorber in the DLW and the effects of the location side and the distribution patterns of the vibration absorbers on the sound insulation performance of the DLW had been confirmed. The deterioration of the sound insulation performance of the DLW due to the mass-air-mass resonance can be improved by the vibration control. In spite of that, setting the vibration absorbers in the cavity causes the movement of the original resonance to the other frequency band and the occurrence of the second resonance. The problems can be dissolved by the sound absorption of the damping material in the vibration absorber. In the investigation, the changes of the sound insulation performance are low correlated with the conditions of the different location side and distribution patterns of the vibration absorbers in the DLW.
Full Paper
Investigations on road noise level spatial variability within a specially designed acoustic balcony
Naish, Daniel A (1), Tan, Andy C C (1), Demirbilek, F Nur (1)
(1) Queensland University of Technology, Australia
ABSTRACT
An investigation into the spatial distribution of road traffic noise levels on a balcony is conducted. A balcony constructed to a special acoustic design due to its elevation above an 8 lane motorway is selected for detailed measurements. The as-constructed balcony design includes solid parapets, side walls, ceiling shields and highly absorptive material placed on the ceiling. Road traffic noise measurements are conducted spatially using a five channel acoustic analyzer, where four microphones are located at various positions within the balcony space and one microphone placed outside the parapet at a reference position. Spatial distributions in both vertical and horizontal planes are measured. A theoretical model and prediction configuration is presented that assesses the acoustic performance of the balcony under existing traffic flow conditions. The prediction model implements a combined direct path, specular reflection path and diffuse reflection path utilizing image source and radiosity techniques. Results obtained from the prediction model are presented and compared to the measurement results. The predictions are found to correlate well with measurements with some minor differences that are explained. It is determined that the prediction methodology is acceptable to assess a wider range of street and balcony configuration scenarios.
Full Paper
The sound transmission loss across ventilation window under active noise cancellation
Tang, Shiu Keung (1), Tong, Yean-ghing (2), Tsui, Kwong-lam (3)
(1) Hong Kong Polytechnic University, Hong Kong
(2) Unversiti Tun Hussein Onn, Malaysia
(3) The Hong Kong Polytechnic University, China
ABSTRACT
An experimental investigation on the use of active noise cancellation to improve the sound transmission loss across a ventilation window was carried out in this study. This experiment series was conducted inside a building acoustic test chamber consisted of two isolated rooms. One of these rooms was reverberant and was used as the receiver room, while the other was made semi-anechoic and it was where the sound source was located. The ventilation window was installed on a brick wall separating these two rooms. Active control with one reference signal, one error microphone and maximum three secondary sources was implemented using the EZ-ANC II MIMO controller. Six well separated microphones which spanned over the whole volume of the receiver room were used to capture the average sound pressure level inside the receiver room. The average sound pressure levels in the receiver room with and without the active control were used to describe the improvement of sound transmission loss by the active control. Among the various control combinations tested, sound transmission loss improvement was found at frequencies below 550Hz. The highest improvement was ~5dB and was found at ~200 Hz. The improvement decreased as frequency increases in general, but there was a dip at ~300 Hz. This dip was believed to be due to a longitudinal resonance in the ventilation window cavity.
Full Paper
Noise Control Potential of Vacuum Isolation Panels
Walters, Sheldon (1), Dance, Stephen (2)
(1) Australia
(2) LSBU, UK
ABSTRACT
In the field of noise control, a commonly evoked acoustic principle is that of sound isolation through the use of massive materials. This paper explores the potential of a vacuum to provide noise control measures. The primary aim is to quantify the relationship between the acoustic attenuation potential of a custom built Vacuum Isolation Panel and a degree of vacuum. Through doing so, this research provides an understanding of the magnitude of physical forces such designs would need to endure to offer any perceivable level of noise reduction. This in turn provides valuable data for future feasibility studies into the design and commercial viability of product development this area. The results showed that the relationship between the quantities is exponential, but only begins to be perceivable above a 90% vacuum level and thereby, 90% mechanical load.
Full Paper
Transient response of complex stiffness system using a green function from the Hilbert Transform and the steady space technic.
Bae, Seung-Hoon (1), Jeong, Wei Bong (1), Cho, Jin-Rae (1)
(1) Pusan National University, South Korea
ABSTRACT
Transient response of complex stiffness system using a green function from the Hilbert Transform and the Steady Space Technic. The characteristics of damped structures which are designed to reduce the strength of vibrations and shock are expressed in complex stiffness. It is not easy to solve second-order differential equations which have complex stiffness because of the governing equation's singular points that cause time solution divergence. To solve this problem, free vibrations of these systems was obtained theoretically by the Hilbert Transform and the Steady Space Technic in which singular points are avoided and provides green function of the convolution integral. The result that are calculated by the numerical integration process for transient responses show accurate amplitude and phase differences. Therefore, it is suggested that this method provides an accurate way to estimate the maximum amplitude of time responses.
Full Paper
Free vibration analysis of elastically connected multiple-beams with general boundary conditions using improved Fourier series method
Du, Jingtao (1), Xu, Deshui (1), Zhang, Yufei (1), Yang, Tiejun (1), Liu, Zhigang (1)
(1) Harbin Engineering University, China
ABSTRACT
Lots of dynamic systems in science and engineering can be simplified as the elastically connected multiple-beams, such as carbon nano tubes and pipes. However, in the majority of current study, just translational spring is considered on beam coupling interfaces. As we know that, not only the translation but also the rotational deformation will occur during beam bending problem. In this work, general beam vibration model is established, in which both two types of translational and rotational springs are taken into account for the coupling interface and both ends. An improved Fourier series is employed for the vibration displacement description for each beam, in which the additional terms are introduced to meet the continuity requirement when the constructed expression is used as the admissible functions. Modal parameters can be determined through the application of Rayleigh-Ritz procedure to the system energy formulation. The current model is then validated through the comparison with those from other analytical approach in open literature. The results show that the current model can made efficient and accurate prediction on the modal property of such complex beam system. The effect of rotational spring on the modal characteristics is also emphasized.
Full Paper
In-Situ Assessment of Building Isolation Bearings
Mackenzie, Neil (1), Lee, Yong Keat (1), Dawson, Bill (1)
(1) Aurecon, Australia
ABSTRACT
A sustainable future has driven the increase in public transport options within cities, many of which are rail corridors under or alongside sensitive facilities. Urban development above rail corridors has led to revitalisation of precincts such as the Riverbank Precinct in Adelaide. This has been inspired by the development of the Adelaide Convention Centre, constructed in stages over the main rail corridor into Adelaide since about 1985. The current stage sought to retain building vibration isolators, originally installed in 1985, to support the new Plenary Hall. This paper outlines a novel use of contra-rotating rotary electric vibrators, ordinarily used for materials handling applications, to measure the performance of building isolators in-situ. It also provides a method for estimating the life expectancy of bearings (usually specified as to be no less than 50 years). Finally it provides insight into design aspects of floor structures subject to combined harmonic loads (from crowd dance activities) while needing to adequately isolate structure-borne noise.
Full Paper
Defect size estimation and analysis of the path of rolling elements in defective bearings with respect to the operational speed
Moazenahmadi, Alireza (1), Petersen, Dick (1), Howard, Carl (1), Sawalhi, Nader (1)
(1) University of Adelaide, Australia
ABSTRACT
This paper investigates and explains the path of a rolling element in the defect zone and the nature of the entry and exit events of the two main features that appear in the vibration signal of a defective bearing. Vibration response and contact forces between the rolling elements and bearing raceways are simulated and compared with the measured vibration signals. Assumptions used in previous defect size estimation methods in describing the path of the rolling elements in the defect zone, are investigated and some discrepancies are identified. These analyses are essential to develop defect size estimation algorithms. Therefore, the defect size estimation results of the existing signal processing algorithms often contain significant errors and are biased for different operational speeds. A method to validate the explanations offered by this study for the true path of rolling elements in the defect zone is proposed. This method can be used for defect size estimations for defective bearings. The research shows that this method is more accurate and less biased for speed when compared with existing methods.
Full Paper
Active noise control based on state feedback by a concentrated mass model
Hisano, Shotaro (1), Ishikawa, Satoshi (1), Kijimoto, Shinya (1), Koba, Yosuke (1)
(1) Kyushu University, Japan
ABSTRACT
We herein propose a new model-based control method, in place of traditional adaptive control, for a low-frequency noise problem in a closed space. The proposed control method is based on state feedback control and a model of the acoustic space obtained by the concentrated mass model. Thus, we can control noise in the entire space. According to the concentrated mass model, the acoustic space is modeled as masses, connecting linear springs, connecting dampers, and base support dampers. Furthermore, a loudspeaker, as a control source, is also modeled by a mass, a spring, and a damper. In the present paper, as a first step, we constructed a coupled analysis model of a one-dimensional sound field and the loudspeaker. We designed the model-based system for the standing sound wave in the low-frequency band. Specifically, we realized a state feedback control system based on a Kalman filter and pole placement. Modal reduction using modal analysis is conducted to reduce the computation time of the controller. Then, we conducted experiments and a numerical simulation of the one-dimensional sound tube to confirm the validity of the analysis model. Moreover, we perform an experiment to control the noise in the sound tube. The noise is reduced around the resonance frequency in the entire space. Therefore, the proposed method is valid for noise control in a closed space.
Full Paper
Active Structural Acoustic Control of Sound Power Radiation from a Soft-Core Sandwich Panel
Kiran, Sahu (1), Jukka, Tuhkuri (1)
(1) Aalto University, Finland
ABSTRACT
In this paper, active control of harmonic sound transmitted through a soft-core sandwich panel is studied. As it has already been shown for the low frequency region, the noise transmission through a soft-core sandwich panel mainly occurs due to the flexural and the dilatational modes [Rimas Vaicaitis, NASA Technical Note, NASA TN D-8516, 1977]. Therefore, in this study, the volume velocity and weighted sum of spatial gradients methods are used to control these modes, and achieve sound attenuation in a broad frequency range. A point force actuator is used as the secondary force to control the radiation modes of the bottom faceplate. Radiated sound power from these two control theories are compared for different values of isotropic loss factor of core. Numerical studies indicate that irrespective of core loss factor weighted sum of spatial gradients method works well in a large frequency band without increasing the radiated sound power unlike the volume velocity method.
Full Paper
Effect of transducer mismatch on the performance of spherical microphone arrays
Rao, Dan
South China University of Technology, China
ABSTRACT
Spherical microphone arrays(SMAs) were widely used in sound field recording, beamforming,etc. for its advantage of high geometrical symmetry. Many factors could affect the performance of SMAs, including transducer errors. In this paper, effect of transducer mismatch in amplitude and phase on the performance of SMAs was studied through simulation calculation. A SMAs with 64 nearly uniformly distributed transducers was used in the simulation. Beam patterns with and without transducer mismatch errors were calculated, and then the differences between those patterns were compared using beam pattern correlation coefficients as the metric. The simulation and anlyasis results show that under the condition that the spherical harmonics expansion order is not larger than ka(the product of wave number and array radius), the correlation coefficient is not less than 0.97 when the max random transducer amplitude error is less than 3dB or the maximum random transducer phase error is less than 10 degree. This result indicates that the performance of SMAs has a good tolerance to transducer mismatch errors when spherical harmonics truncation order is not larger than ka. While ka less than truncation order, great errors occur due to low-frequency boost nature of SMAs signal processing.
Full Paper
Active noise reduction of a coupled rectangular cavity using active wave control
Watanabe, Motoya (1), Iwamoto, Hiroyuki (1), Tanaka, Nobuo (2)
(1) Seikei Univercity
(2) Tokyo Metropolitan Univercity
ABSTRACT
The objective of this study is to generate a quiet space in a coupled rectangular cavity by suppressing a travelling wave caused by vibration of a flexible panel. Firstly, this study begins with description of an enclosed sound field from a wave point of view by introducing a one-dimensional transfer matrix method for three-dimensional space. Next, a concept of modal coupling method is utilized to model a coupled rectangular cavity. Furthermore, introducing multiple control sound sources in an arbitrary plane in the target space, the control law is derived that eliminates a travelling wave passing through the control plane. Finally, numerical simulations are carried out to demonstrate the validity of the proposed method. As a result, it was clarified that the proposed method enables to generate a quiet space by cancelling transmitted waves.
Full Paper
Withdrawn2
Withdrawn2,
ABSTRACT
Withdrawn2
Design of Active Noise Control System Applied to Helicopter Cabins
Yan, Shenggang (1), Tang, Dakai (2), Zhang, Xiaonei (1), Yu, Haoxin (1)
(1) Northwestern Polytechnical University, Xi\'an, China
(2) Shaanxi Fenghuo Electronics Co. Ltd., China
ABSTRACT
The high low-frequency tonal noise in the helicopter cabin has strongly negative influences on safety, personnel mind and body health of the pilots and passengers. In order to control such type of noises, an active noise control (ANC) system is developed for a mock-up of the helicopter cabin. The presented ANC system is divided into three parts: acoustic signal inputs, SMJ320C6415 DSP based active control algorithm implementation, and the generation of secondary sound sources. The main characteristics for the active controller are given by (1) power supply with DC 27V, 500W, (2) 14 error signal channels and 16 secondary signal channels, (3) 2 reference signal channels, and (4) total weight of 15kg (including microphones and speakers). Finally, a series of experiments within a helicopter cabin mock-up are carried out using the designed active control system. It is shown from the experimental results that the active control system can operate smoothly and steadily.
Full Paper
Calibration Methodologies and the Accuracy of Acoustic Data
Beyers, Craig
Air Noise Environment P/L, Australia
ABSTRACT
The precision and accuracy of acoustic instrument calibrations is fundamental in ensuring the validity and defensibility of acoustic measurements. The measurement error is additive to the overall uncertainty or error associated with acoustic calculations and modelling techniques, where these rely on measurement data as a source of acoustic data. Therefore, the tolerance of the calibration is a fundamental component in determining the accuracy of all applications that rely on acoustic measurement data. National and International metrology standards define the methodologies adopted in acoustic calibration. Currently the IEC 61672 standard is adopted for the periodic testing of field instruments. This paper provides an overview of the changes in calibration requirements of the IEC 61672 standard relative to the earlier versions of IEC 61672 and the IEC 652 standard. The paper then explores in more detail from an end user perspective the implications of calibration methodologies and the overall accuracy of acoustic data.
Full Paper
The Effect of Wind on Low Frequency Noise
Lin, I-Chun (1), Hsieh, Yein-Rui (1), Shieh, Ping-Fei (1), Chuang, Hsun-Cheng (1), Chou, Li-Chung (1)
(1) Taiwan EPA, Taiwan
ABSTRACT
The impact of wind on the measurement of low frequency noise is a topic that is worth researching into. Since the existing "Measuring Method of Environmental Low Frequency Noise" applies only to indoor measurement of low frequency noises (According to the provision of law in our country, low frequency refers to the frequency range of 20Hz ~ 200 Hz), if a petitioner demands measuring the low frequency noise at an outdoor location, there is no method and/or control standard for outdoor measurement of low frequency noise currently available in our country. This paper aims to explore the effect of the windscreen on reducing wind noise. It is hoped that the findings of the study can serve as reference for formulating method and control standard for outdoor measurement of low frequency noise. When conducting noise measurement, if the sensor of the sound meter is affected by the effect of wind force, there is an influence of wind noise on the measurement, particularly at low frequencies (20 Hz ~ 200 Hz). This study aims to explore the effect of wind noise on outdoor noise measurement at low frequencies. Through comparing and probing into the effects of wind noise when using different types of windscreens, we have obtained some noticeable noise reducing results under different wind speeds when using different types of windscreens, which might serve as reference for selecting windscreens when conducting outdoor noise measurement at low frequencies.
Full Paper
First results in the realization of the unit Watt in airborne sound
Voelkel, Katharina (1), Bethke, Christian (1), Brezas, Spyros (1), Wittstock, Volker (1)
(1) Technische Bundesanstalt Braunschweig, Germany
ABSTRACT
Sound power - though a main quantity in acoustics - is not a traceable quantity to this day because a standard device for the realization of the unit watt has not been developed. Changing this is one goal of a research project funded by the European Metrology Research Programme (EMRP). Basis for the realization of the unit watt in airborne sound is an embedded oscillating solid body whose sound power output can be calculated using Rayleigh's integral with measured velocity distributions on the radiator surface. Ideally, the solid body moves as a rigid unit and acts as a monopole. However, measurements show that a uniform movement of the radiator surface is difficult to achieve. It will be investigated whether such a source can nevertheless be considered as a monopole and at which frequencies. Thus, analyses on the comparability of numerical and analytical data as well as an investigation of the dependency of uncertainties on discretization of the measured radiator surface will be presented. Calculations will be compared to sound powers determined from sound pressure measurements on an enveloping surface for further verification.
Full Paper
Influence of reflecting plane having finite surface density on sound power level of reference sound sources calibrated in hemi free-field
Yamada, Keisuke (1), Takahashi, Hironobu (1), Horiuchi, Ryuzo (1)
(1) NMIJ/AIST, Japan
ABSTRACT
The NMIJ, National Metrology Institute of Japan planned to start calibration service for reference sound sources (RSSs) by 2015 and we have been developing the RSS calibration system in accordance with ISO 6926. In our system, hemi-anechoic environment necessary for the calibration is realized by laying down wooden boards on a wire meshed floor of our anechoic room. In this study, we investigated the influence of such a reflecting plane having finite surface density on sound power level of the RSS theoretically and experimentally. We especially examined sound energy transmission through wooden boards and their vibration caused by the RSS operation. We also experimentally confirmed that our hemi-anechoic environment satisfies an inverse square law of sound intensity within a tolerance in ISO 3745. Furthermore, sound power level of the RSS determined by our system agreed with that by the SP, Technical Research Institute of Sweden within a range of SP's expanded uncertainty. These results show that our hemi-anechoic environment is suitable to determine sound power level of RSSs in accordance with ISO 6926.
Full Paper
Influence of Structural Elasticity on Trailing Edge Noise
Chen, Li (1), Kessissoglou, Nicole (2)
(1) DSTO, Melbourne, Australia
(2) UNSW Australia, Australia
ABSTRACT
For an airfoil, a hydrofoil or a control surface in high Reynolds number flow, the noise generated by the turbulent boundary layer is scattered by the trailing edge and then radiated efficiently. This is an important broadband noise problem, particularly at high frequencies. For aeronautical applications, estimations of trailing edge noise are mainly based on the assumption of rigid surfaces. In underwater applications, the foils may no longer be considered as rigid. The trailing edge noise is then the result of the vibro-acoustic coupling of the flow and the foils. In this paper, the influence of structural elasticity on trailing edge noise generation is investigated. The turbulent flow loading on a 2D hydrofoil is modelled using a Reynolds-Averaged-Navier-Stokes based computational fluid dynamics approach. The fluid loading is then applied to the bending wave equation of a thin plate to predict elastic edge noise. Rigid edge noise is also predicted using the flow loading combined with a Green's function. Four different materials are examined in this study.
Full Paper
Wind Tunnel Test of Trailing Edge Serrations for the Reduction of Wind Turbine Noise
Fischer, Andreas (1), Bertagnolio, Franck (1), Shen, Wen Zhong (1), Madsen, Jesper (2), Madsen, Helge Aagaard (1), Bak, Christian (1), Devenport, William (3), Intaratep, Nanyaporn (4)
(1) Technical University of Denmark, Denmark
(2) LM Wind Power A/S, Denmark
(3) Virginia Tech University, USA
(4) Virginia Tech University, USA 3 LM Wind Power A/S, Denmark
ABSTRACT
We tested trailing edge serrations for the reduction of the emitted sound from an aerofoil in the aero-acoustic wind tunnel of Virginia Tech University. The aerofoil was developed for the use on the outer part of the blade of a wind turbine. Two different serration geometries were tested. The geometry of the serrations is confidential to LM Wind Power A/S. The far field sound was measured with a microphone array outside the test section. Additionally the aerofoil surface pressure was measured at 62 chordwise positions. The chord based Reynolds number was 1.6 million. The serrations had very small influence on the aerodynamic performance of the aerofoil. At low angles the emitted sound was decreased by up to 8 dB, but the noise reduction became less with increasing angle of attack. At very high angles of attack the emitted sound was increased. The measured far field sound was compared to a modified TNO model using Howe's expression for sound emitted from a serrated edge. The comparison was good for the straight edge configuration, but the noise reduction by a serrated edge was significantly overestimated by the model. The expression for sinusoidal serrations gave better results than the one for saw-tooth serrations.
Full Paper
Measuring owl flight noise
Geyer, Thomas (1), Sarradj, Ennes (1), Fritzsche, Christoph (2)
(1) BTU Cottbus, Germany
(2) Thuringian State Institute for Environment and Geology, Germany
ABSTRACT
It is well known that most genera of owls are able to fly almost silently in order to hunt their prey. However, this knowledge is actually based on very few quantitative studies only. This is especially interesting regarding the fact that, against the background of increasing air traffic, the unique plumage adaptations of the owl responsible for the silent flight are the motivation behind various airframe noise reduction techniques such as serrations or porous trailing edges.Both by reviewing existing data and by means of appropriate experiments, the paper will first illustrate the special feather adaptations of owls and will expand upon their contribution to the silent flight. Then, following a brief review of existing measurement data on the silent owl flight from past studies, the paper will focus on more recent measurements of the noise generated by gliding owls. Thereby, two different approaches were followed: First, outdoor measurements of the noise emitted by gliding owls were performed using microphone array technology and a high speed camera setup to capture the flight path of the birds. Second, indoor measurements in an aeroacoustic open jet wind tunnel revealed the noise generated by prepared wings as well as their aerodynamic performance in terms of lift and drag forces. In both cases, special attention was paid to the difference between the flight noise of the owl compared to the noise of other, non-silently flying birds.
Full Paper
Analysis and Control of Flow-Acoustic Feedback-Loop Interactions in Transitional Airfoils
Golubev, Vladimir (1), Nguyen, Lap (1), Mankbadi, Reda (2), Roger, Michel (2)
(1) Embry-Riddle Aeronautical University, USA
(2) Ecole Centrale de Lyon, France
ABSTRACT
Our recent numerical and experimental efforts are reviewed examining flow-acoustic resonant interactions in transitional airfoil boundary layers and means of control of the resulting prominent, tonal trailing-edge noise sources. Experimentally recorded unsteady responses of loaded, transitional NACA0012 airfoil reveal operational regimes characterized by the presence of the shifted ladder-type tonal structures with dual velocity dependence observed in the surface pressure and the acoustic signals. High-fidelity numerical efforts employ a 6th-order Navier-Stokes solver implementing a low-pass filtering of poorly resolved high-frequency solution content to retain numerical accuracy and stability over a range of transitional flow regimes. 2D and 3D (ILES) numerical experiments investigate the behavior of the boundary-layer statistical moments during the transitional flow regimes characterized by the presence of separation regions and the resulting formation of the highly-amplified instability waves scattered into noise at the airfoil trailing edge, thus triggering and sustaining the acoustic feedback-loop process. The current paper particularly focuses on the sensitivity of the airfoil flow-acoustic interactions (and the resulting acoustic signature) to the upstream flow conditions.
Full Paper
Effects of wing tip shaping on noise generation
Klei, Christine E (1), Buffo, Rainer M (1), Stumpf, Eike (1)
(1) RWTH Aachen University, Germany
ABSTRACT
Geometrical shaping of wing tips leads to variations in the axial and tangential velocity components of the developing vortex. This effect is taken as basis for further analyses of a generic wing model with exchangeable tips in a wind tunnel. Flow field measurements using 3C-PIV and acoustic measurements are performed in order to indicate how changes of the wing tip shape affect noise generation caused by different flow development. High-resolution flow field measurements allow for detailed analyses of the vortex structure and distribution around the wing tip region. Furthermore, beamforming methods are used in order to localize the noise source and show the overall noise reduction potential of different wing tip shapes. The combination of PIV and acoustic measurements allows for a better understanding of underlying physical effects and correlations. Analyses of the data prove a variation of both, flow field and noise characteristics, dependent on the geometrical shape of the wing tip.
Full Paper
The NOISE database and other electronic and web-based tools for researchers and educators
Beach, Elizabeth Francis (1), Gilliver, Megan (1), Williams, Warwick (1)
(1) NAL Sydney, Australia
ABSTRACT
NAL and the HEARing CRC are increasingly seeking ways i) to translate our hearing loss prevention research findings and ii) promote noise awareness and hearing health via electronic and online methods. The aim is to translate our research work into tools that are broadly accessible to both researchers and the general public regardless of location. This presentation will discuss some recently developed online initiatives with a focus on the NOISE database project. The NOISE database allows researchers to access and contribute to its collection of 895 noise level measurements obtained at a wide range of different leisure activities in Australia and across the globe. Also included will be an introduction to our 'Know Your Noise' website aimed at young adults. The site allows anyone to learn more about the consequence of their noise exposure through the Noise Risk Calculator and other elements of the site.
Full Paper
Audio and Acoustical Response Analysis Environment (AARAE): a tool to support education and research in acoustics
Cabrera, Densil (1), Jimenez, Daniel (1), Martens, William Leigh (1)
(1) University of Sydney, Australia
ABSTRACT
AARAE is a MATLAB-hosted environment for measurement and analysis of room acoustics and audio systems, designed to support education and research in audio and acoustics. While it already provides a wide range of test signals, and measurement, processing, and analysis methods, one of its main features is easy extensibility. Students new to signal processing (and MATLAB) can use it from its graphical user interface (without any need to write code), whereas more advanced students can develop implementations of pre-existing or novel measurement, processing and analysis algorithms using templates that allow quick integration of functions into the graphical user interface. AARAE was introduced into acoustics teaching at the University of Sydney in 2014, and it is used in both introductory and advanced units. While most of the code for the current version of AARAE was written by the authors, coursework students have contributed to functions in areas such as speech intelligibility, distortion, reverberation parameters and background noise rating. This paper illustrates how AARAE is used in teaching, highlighting some recent student projects in AARAE. It also illustrates how AARAE has been used to support research and research training.
Full Paper
Experiences of MOOCs and 25 year short courses for industries
Kim, Yang-Hann
Korea Advanced Institute of Science and Technology, Republic of Korea
ABSTRACT
Recently, the impact of MOOCs(Massive Online Open Courses) is huge not only in terms of its number of registration but also its wide geographical, age, and educational background. This paper introduces the courses that are related with noise/acoustics in MOOCs: its current statistics. KAIST has been offering noise related short course for more than 25 years: one is for modal analysis and another is to introduce the fundamentals of acoustics. This paper attempts to compare the recent MOOCs courses related with noise/acoustics, and others, including the conventional offline short courses: pros and cons.
Full Paper
European Acoustics Association Schools
Maffei, Luigi (1), Vorländer, Michael (2), Jambrošić, Kristian (3)
(1) Second University of Napoli, Italy
(2) RWTH Aachen University, Germany
(3) University of Zagreb, Croatia
ABSTRACT
European Acoustics Association Schools are an integral part of the Young Acousticians Program of EAA. Meanwhile they consist a) of various "Hot Topic" courses for graduate level and b) of an introductory course "Approaching Acoustics" for undergraduate students. All parts are taught by internationally recognized and distinguished experts in acoustics. The first EAA (Summer) School was held in Ljubljana, Slovenia, in 2010 with short courses on "Soundscapes", "Voice and Musical Acoustics", "Building Acoustics", "Hydroacoustics", "Numerical Methods", "Psychoacoustics" and "Ultrasound". The second EAA (Winter) School was held in Merano, Italy, in 2013 with advanced courses on "Cutting Edge in Spatial Audio", "FEM and BEM", "Synergies between Environmental Noise Control and Soundscape Approach", "Understanding Musical Instruments in Practice", and "Introduction to Aeroacoustics". Furthermore, an undergraduate course "Approaching Acoustics" was attended by 100 students from 18 countries. In the paper, the background and the motivation of this initiative is illustrated. Content, organization and future plans of integration in the European higher education in acoustics are discussed.
Full Paper
Car mechanic training course and acoustic technique education
Nakamura, Kinji
Non-profession engineer, Japan
ABSTRACT
This report is showing of one example of the acoustic technique education adopted at the car mechanic training course. The author thinks that the anti-noise is important as one of the work of the car mechanic. In addition, the purpose of it is to urge understanding to a sound phenomenon of the car. For instance, it will lead to technological acquisition of the noise level measurement, frequency analysis, and the evaluation test when how to the frequency component with different exhaust noise to feel it is evaluated by the auditory sensation. This evaluation is an estimate of the magnitude to noisy feeling. The examination sound is an adjacent exhaust noise of the motorcycle and various reproduction sounds from the audio speaker. It is thought that making the student think about the current state and the content of the regulation of the automobile noise based on the above-mentioned experimental result can deepen understanding to the necessity of the noise control, and assumes it to be an outline of this education of giving the chance.
Full Paper
Study and practice of joint teaching between ZJU and UWA
Pan, Jie (1), Stone, Brian (1), Guzzomi, Andrew (1), Sun, Hongmei (1), Zheng, Jing (2), Tong, Yuhui (3), Du, Xuhao (2), Xia, Yinzhu (2)
(1) The University of Western Australia, Australia
(2) Zhejiang University, China
(3) The University of Western Australia, Australia, Zhejiang University, China
ABSTRACT
A joint international unit on dynamics, vibration, and sound was established in early 2014 for engineering students in their penultimate year at Zhejiang University (ZJU), China, and at the University of Western Australia (UWA), Australia. The unit was taught entirely in English. Dynamics and sound topics were taught live to ZJU students and vibration topics live to UWA students. Recordings were uploaded to websites so that students at each university could access the material. A set of quiz questions supplemented each recorded lecture. Tutorials and laboratory practical classes (weighted 15%) were delivered using a combination of live teaching/demonstrations and self-learning via online recordings. A group project (weighted 25%) using receptance encouraged students to self-study three chapters of an e-book on vibration. Additionally, it provided an opportunity for teamwork, internet forum discussion, computer programming, and optimization. Apart from the final exam (weighted 60%)—conducted simultaneously at each university—all assessments were completed online. This paper summarizes some key observations of the effects of various teaching methods on the students' effort and performance at the two universities. In addition, it highlights the need for integrated live lectures, online support, and a variety of practices for effective knowledge and skills transfer.
Full Paper
Experimental validation of the modelling of surface roughness effects by an effective impedance
Faure, Olivier (1), Gauvreau, Benoit (1), Junker, Fabrice (2), Lafon, Philippe (2)
(1) Ifsttar Nantes, France
(2) EDF R&D, France
ABSTRACT
Natural grounds can exhibit small geometry irregularities, compared to the wavelength, which are called surface roughness. Using effective impedance is a useful way to model the effects of surface roughness on outdoor sound propagation, particularly in numerical methods as it avoids the meshing of small irregularities. In this paper, firstly an effective impedance model taking into account the surface roughness spectrum of the ground is exposed. Secondly, an experimental campaign of sound pressure measurements above 1/10 scale 2D rough surfaces is presented. The same profile characterized by a gaussian roughness spectrum is designed in two polystyrene boards coated with resin. One board is felt-covered to simulate an absorbing rough surface and the other is left uncovered to simulate a reflective rough surface. Finally, the experimental results are compared to analytical calculations with the effective impedances corresponding to the two experimental rough surfaces, respectively. Those results show good agreement, thus validating the effective impedance approach and allowing more accurate SPL predictions for future impact studies in environmental acoustics.
Full Paper
Acoustic Study and Visualization of a complex echo at the Klondike Bluffs, in the Arches National Park, Utha, USA
Heilmann, Gunnar (1), Navvab, Mojtaba (2), Boeck, Magdalena (1), Vonrhein, Benjamin (1)
(1) gfai tech, Germany
(2) University of Michigan, USA
ABSTRACT
Physical explanations for echoes are widely known. Although measuring an echo with common methods using a single microphone is simple, it does not provide a full description of the behavior of each individual reflection that take part of an echo of this large scale environment without knowledge of the exact topology. The actual directions of each echo remain unknown. Only simulations will provide some understanding but are only as good as the model and all its assumptions. The aim of this paper is to investigate and uncover the participating reflections for an echo and create detailed visualization of the echo reflections scheme. The measured echo was first discovered by Gunnar Heilmann in September 2009 and was now measured and will be described here for the first time. It is particularly interesting because of its multitude (more than ten reflections) and order of individual echo reflections and its 3D distribution and timing surrounding the receivers' location.
Full Paper
Field experiment on sound propagation from an elevated directional source
Sakamoto, Shinichi (1), Tkanashi, Toshikazu (2), Yokoyama, Sakae (3), Ishii, Hirokazu (4)
(1) Institute of Industrial Science, The University of Tokyo, Japan
(2) INC Engineering Co., Ltd., Japan
(3) Kobayasi Institute of Physical Research, Japan
(4) Japan Aerospace Exploration Agency, Japan
ABSTRACT
The authors investigate outdoor sound propagation from a directional source by field experiments. Results on ground-to-ground sound propagation are reported in this conference by another paper. In addition to an experimental investigation on ground-to-ground sound propagation from a directional source, in this report, results of an experiment on air-to-ground sound propagation from an elevated directional source lifted by a tethered balloon is described. In this experiment, a horn type loudspeaker was raised at the heights of about 100 and 200 m, and sound propagation characteristics from the source to receivers on the ground were analyzed from impulse responses measured by a swept sine method. As a result of the experimental study, which was made under a meteorologically calm condition, it was confirmed that the sound propagation characteristics can be accurately estimated by considering the directivity characteristics of the sound source in low and middle frequencies, and that they are considerably affected by meteorological effects.
Full Paper
Field experiment on ground-to-ground sound propagation from a directional sourcee
Takanashi, Toshikazu (1), Sakamoto, Shinichi (2), Yokoyama, Sakae (3), Ishii, Hirokazu (4)
(1) INC Engineering Co., Japan
(2) University of Tokyo, Japan
(3) Kobayasi Institute of Physical Research, Japan
(4) Japan Aerospace Exploration Agency, Japan
ABSTRACT
When predicting sound propagation in long distance, meteorological effects resulting from wind and temperature should be taken into consideration. Regarding this problem, many studies have been carried out by field measurements, numerical analyses and physical experiments. To predict and assess traffic noise by vehicles, trains and aircrafts, the sound sources are roughly modeled as omnidirectional. In reality, however, the sources have their inherent directivities according to their shapes, and the directivity can affects noise propagation characteristics as well as the meteorological effects. In this study, a field experiment on ground-to-ground long distance sound propagation using an omnidirectional loudspeaker and two types of directional loudspeakers were conducted at a flat field which approximately satisfied hemi-free field condition. To examine the relationship between the directivity effects and the meteorological effects, sound propagation characteristics by an omnidirectional loudspeaker and those by directional loudspeakers were compared. In addition, sound propagation by the omnidirectional point source was analyzed using Crank-Nicholson Parabolic Equation analyses and the experimental results were validated. Consequently, it was confirmed that sound propagation from the directional sources showed the same trend for excess attenuation characteristics as that from the omnidirectional source by considering its directional characteristics.
Full Paper
Withdrawn7
Withdrawn7,
ABSTRACT
Withdrawn7
The Numerical Prediction and Features Analysis of Cylindrical Shell Acoustic Radiation Noise
Cao, Hongli (1), Fang, Shiliang (1), An, Liang (1)
(1) Southeast University, China
ABSTRACT
Target feature is important information in underwater target classification. A characteristic analysis in underwater cylindrical shell acoustic radiation noise was studied in this paper based on the finite element/boundary element method (FE/BEM) method. Firstly, the numerical prediction of cylindrical shell acoustic radiation noise based FE/BEM method was verified by the numerical and analytical solutions. The characteristic of acoustic radiation was studied with different cylindrical shell size, material, excitation points, shape, observing position. Simulation results show that the features in acoustic radiation noise were relevant to the medium, radius and shape. The features analysis had some guidance significance with the target identification.
Full Paper
Modelling the forced response of a stiffened structure
Forrest, James
DSTO, Australia
ABSTRACT
Different analytical approaches can be used to model the forced response of the beam-stiffened plates or shells that are commonly found in many practical structures from ships to aircraft. A popular method is to smear the mass and stiffness properties of the beam stiffeners to give an orthotropic plate or shell. This is simpler than modelling discrete stiffeners. This paper considers the example problem of a cylindrical shell with ring stiffeners. Previous work using periodic structure theory has shown that the calculated wave propagation behaviour in this cylinder using a smeared shell model is different from that with the stiffeners modelled discretely. The current work calculates the forced response of the cylinder using both models and compares the results to determine the range of applicability of the smeared shell approach.
Full Paper
Coupled analysis of two-dimensional acoustic and
membrane vibration by concentrated mass model
Ishikawa, Satoshi (1), Kijimoto, Shinya (1), Owaki, Ryoma (2), Matsuo, Ataru (1)
(1) Kyushu University, Japan
(2) Mitsubishi Electric Corporation, Japan
ABSTRACT
In the finite element method of a structural-acoustic coupled analysis, the mass matrix and the stiffness matrix are not symmetrical. Therefore, the modal analysis cannot be applied directly to the coupled problem. In our previous study, a concentrated mass model was proposed to analyze a two-dimensional acoustic analysis. The model consists of the masses, the connecting springs. It is very easy to couple the structure and acoustic field by the concentrate mass model. Furthermore, the mass matrix and the stiffness matrix are symmetrical. In this paper, we propose a concentrated mass model to perform a coupled analysis of a two-dimensional acoustic and a membrane vibration. And we propose a coupling method to arrange of the masses of the air near the membrane. To confirm the validity of the proposed model, the natural frequency obtained by the concentrated mass model is compared with the natural frequency by the modal coupling method. These results are in good agreement. Therefore, it is concluded that the proposed model is valid for the coupled analysis of an acoustic and a vibration analysis.
Full Paper
A study of the assumptions used in statistical energy analysis
Lafont, Thibault (1), Totaro, Nicolas (2), Le Bot, Alain (3)
(1) LTDS, France, LVA, France
(2) LVA, France
(3) LTDS, France
ABSTRACT
This paper is a discussion on the coupling strength, the frequency bandwidth and indirect coupling loss factor in statistical energy analysis. The example of coupled oscillators is taken. First, it is shown that the coupling power proportionality is always valid for two coupled oscillators for any strength of coupling as long as the resonant modes are within the frequency band. Then, the case of three coupled oscillators indicated that the apparition of indirect coupling loss factors depends on the coupling strength. Finally, it is shown that modes outside the frequency bandwidth of excitation can lead to invalid the reciprocity relation. Some test cases are presented to illustrate these conclusions.
Full Paper
The Adaptive Order FEM approach for vibro-acoustic simulations: a report on a newly implemented technology with application examples demonstrating its superior performance to conventional FEM methods
Vansant, Koen (1), Hallez, Raphael (1)
(1) Siemens PLM, Belgium
ABSTRACT
This paper will discuss a newly implemented Adaptive Order Finite Element Method (FEM AO) and intents to illustrate its superior performance to conventional FEM methods. The power of the new FEM AO technology lies in the adaptive model size, which is accomplished by element order increase (p refinement) and varies with frequency. This allows to work with an as lean as possible model at each frequency while at the same time guaranteeing the requested accuracy. Three different application examples are provided in which the computational performance of the new FEM AO approach is compared with that of a conventional FEM method. Occasionally the comparison may also include results from advanced Boundary Element Method (BEM) approaches, like the Fast Multipole BEM. In the context of automotive applications, a first case reports on the simulation of acoustic transfer functions for a full vehicle model up to 4 kHz to be used in a transfer path analysis model for prediction of pass-by noise. A second application example concerns the noise radiating from a fan of an aero-engine, including the effects of flow. A third example will illustrate the performance of a computation of the transmission loss for an industrial muffler. The examples show that FEM AO delivers equally accurate results 2 to 20 times faster compared to a conventional FEM and with a more efficient use of in-core memory.
Full Paper
A reduced-order stochastic finite element analysis for structures with uncertainties
Yang, Ji (1), Faverjon, Béatrice (2), Peters, Herwig (1), Kessissoglou, Nicole (1)
(1) UNSW Australia, Australia
(2) INSA-Lyon, France; UNSW Australia, Australia, UNSW Australia, Australia
ABSTRACT
his work examines the effects of uncertain material and geometry properties on the dynamic characteristics of a simply supported plate. The forced responses of the plate are predicted using the polynomial chaos expansion method. The stochastic system equations are transformed to a set of deterministic equations using Galerkin projection. In order to improve the computational efficiency when attempting to examine the structure with many degrees of freedom, the Arnoldi-based Krylov subspace technique is implemented to reduce the number of degrees of freedom in the finite element model, before the polynomial chaos expansion is applied. The combined stochastic finite element analysis and model order reduction technique is shown to provide accurate results with significantly reduced computational effort.
Full Paper
Experimental Analyses of Vibration and Noise of Faulted Planetary Gearbox
Li, Zhuang
McNeese State University, USA
ABSTRACT
Epicyclic gear trains are widely used in various industrial sectors due to their advantages over fixed-axis gears, such as high torque capability, compact size, differential and planetary designs, ease of adjusting gear ratios and even directions of rotation. This research focuses on planetary gearbox whose degree of freedom is one. The geometry and dynamics of the planetary gear train are quite complicated compared with the fixed-axis gear train. In an earlier research, three theoretical models for faulted sun, planet, and ring gears were analyzed and the signature frequencies of the three cases were derived. In this paper, experiments were conducted on a Drivetrain Diagnostics Simulator with various faults of the sun gear in order to verify the previously proposed theoretical models. Both the vibration and noise signals were collected and analyzed using signal processing techniques in the time and frequency domains. The sidebands around gear mesh frequency due to the fault signature frequencies are also discussed accordingly. The signals of healthy and faulted gear trains were also compared carefully. The existence of the signature frequency can be used to detect mechanical defects and prevent catastrophic consequences.
Full Paper
Parametrically Excited Vibration in Rolling Element Bearings
Srinath, R (1), Sarkar, A (1), Sekhar, A Seshadri (1)
(1) IIT Madras, Chennai, India
ABSTRACT
A defect-free rolling element bearing has a varying stiffness. The variation of stiffness depends on number of rolling elements, their configuration and cage frequency. The time-varying characteristics of the stiffness results in a parametric excitation. This may lead to instability which is manifested as high vibration levels. An FEM simulation is performed to evaluate stiffness in each configuration of rolling elements and is used to study the variation of direct stiffness and cross coupled stiffness. The obtained stiffness variation is expanded into a Fourier series to form the equation of motion for the bearing vibration. As the stiffness varies with cage frequency, stiffness term in the equation of motion is periodic with parametric excitation. Hence, the equation of motion is a 2-DOF coupled Mathieu equation. Based on Mathieu parameters and cage frequency there exists unstable rpm ranges for a particular bearing. Floquet theory is employed to find out the stable and unstable regions. This involves finding out maximum Floquet exponent using Monodromy matrix. The results obtained through Floquet theory are in agreement with the numerical solution of the governing equations.
Full Paper
Vibration reduction of brush cutter considering human response characteristic
Uemura, Masanori (1), Yoshida, Junji (1), Miyakawa, Shigeru (2), Oono, Teruhito (2), Ishikawa, Daiga (2)
(1) Osaka Institute of Technology, Japan
(2) Taiseimonac Co., Japan
ABSTRACT
Balancing brush cutter was developed to be used safety and easy handling. In this study, we tried to improve the vibration through subjective evaluation tests and the vibration analyses. In the first subjective test, participants evaluated handle vibration feelings of some brush cutters and the frequency characteristic to the vibration feeling was clarified. Subsequently, the handle vibration from 100 to 200 Hz was found to be large and the handle pipe structure had high influence on the large vibration through measurements and analyses of the handle vibration at the operational condition. We then applied several countermeasures including modification of the handle pipe length to reduce the vibration. As a result, the handle vibration of the brush cutter was reduced much and the vibration feeling was improved.
Full Paper
Withdrawn4
Withdrawn4,
ABSTRACT
Withdrawn4
Coupling analysis of torsional vibration and engine rotational speed control system of marine propulsion shating
Yu, Shuwen (1), Liu, Yan (1), Han, Xiao (1), Chen, Meilong (1), Li, Wanyou (1)
(1) Harbin Engineering University, China
ABSTRACT
For general simulation of engine rotational speed control system, the shafting is always assumed to be rigid. The torsional vibration characteristics of the shafting are neglected. The possible relationship between between the rotational speed oscillation phenomenon and coupling of the torsional vibration and the engine rotational speed control system will not then be revealed in such simulation. In this paper, by assuming the shafting to be elastic instead of rigid, a coupling simulation model is established. The influenced of different PID control parameters and variation of the propeller damping to the speed-control performance are analysed to illustrate the coupling characteristics of the shafting torsional vibration.
Full Paper
The same reverberation time in two identical rooms does not necessarily mean the same levels of speech clarity and sound levels when we look at impact of different ceiling and wall absorbers.
Campbell, Colin (1), Svensson, Carsten (1), Nilsson, Erling (1)
(1) Saint-Gobain Ecophon AB, Sweden
ABSTRACT
It is common to only use Reverberation Time (RT) for setting the acoustic conditions in a classroom for teaching and learning activities. To calculate the RT in rooms with ceiling absorption is common but this data can also be misleading. Indeed, we measured the same RT values in two identical rooms with different acoustic treatment, even though the calculations predicted significant differences and interestingly the rooms are also be perceive quite differently in reality. Assuming that the user perceptions are valid, the measured RT data alone leaves us in the dark when seeking to explain the difference in human user perception. Measuring additional room acoustic parameters such as speech clarity and the difference in sound levels, identifies other differences between the two rooms with the same RT and points to why only one of the two rooms seems fit for purpose as a group activity room. We will discuss how to achieve acoustic comfort in classrooms; low RT, low sound levels and high speech clarity. In addition to commonly accepted low RT values we will discuss recommended objective values for good Speech Clarity to support good speech communication activities in typical teaching and learning rooms in real life situations.
Full Paper
An investigation into the acoustics of an open plan compared to enclosed Kindergarten classroom
Mealings, Kiri Trengove (1), Buchholz, Jorg M (2), Demuth, Katherine (1), Dillon, Harvey (3)
(1) Macquarie University, Australia
(2) Macquarie University, Australia, Macquarie University, Australia
(3) National Acoustics Laboratories, Australia
ABSTRACT
Open plan classrooms, where several class bases share the same space, have recently re-emerged in Sydney primary schools. This case study examines the acoustics of a mid-range open plan Kindergarten classroom containing 91 students, compared to an enclosed classroom of 25 students. Ambient noise levels, intrusive noise levels, occupied background noise levels, and teacher's speech levels were recorded in both classrooms during different activities. Room impulse responses using logarithmic sweeps were also recorded in each classroom for different teaching scenarios. From these recordings, signal-to-noise ratios, speech transmission index scores, and reverberation times were calculated. The results revealed much higher intrusive noise levels in the open plan classroom, resulting in signal-to-noise ratios and speech transmission index scores to be well below those recommended in classrooms with students of this age. Reverberation time in the open plan classroom was also outside the recommended level. Additionally, occupied background noise levels in both classroom types were well above recommended levels. These results show the importance of further research into the noise levels of open plan classrooms to determine if they are suitable learning spaces for young students. The impacts of noise on speech perception, learning, and teacher's vocal health are discussed.
Full Paper
A pilot study on the influence of language on the results of speech intelligibility tests in classrooms
Radosz, Jan (1), Zawieska, Wiktor M (1)
(1) Central Institute for Labour Protection - National Research Institute, Poland
ABSTRACT
Numerous studies have shown that teachers often speak louder in classrooms because of the acoustic properties of the spaces. To improve the acoustics in classrooms, it is necessary to develop relevant acoustic criteria. Existing evaluation scales for parameters of room acoustics have been developed on the basis of studies of adults for a variety of languages (e.g., Dutch and English). One of the issues still not fully recognized is the effect of the respondents' language and age on the results of speech intelligibility tests. This paper presents a pilot study of the speech intelligibility of Polish-speaking children (10-13 years old) in conjunction with parameters of room acoustics. It also compares studies of speech intelligibility for other languages. Our study confirmed a relationship between the results of speech intelligibility tests and speech transmission index STI for classrooms with varied acoustics. It also showed that the results of Polish tests are similar to Anderson's and Jacob's results for English.
Full Paper
New generation learning environments: creating good acoustic environments - policy to implementation
Robinson, Amanda (1), Rose-Munro, Leanne (2)
(1) Marshall Day Acoustics, Australia
(2) Learning Spaces Consultancy
ABSTRACT
The introduction of new technologies in schools has resulted in a paradigm shift in the way educational spaces are created and used. Today's learning environments are flexible speaking and listening spaces where collaboration, group work, complex problem solving, digital information gathering and publishing occur. Changes in technology and legislation have highlighted the need for equitable access to learning environments. Good acoustic design is essential. This cross-disciplinary paper co-written by an acoustical engineer and an educator discusses the importance of good acoustic design within new generation learning environments to promote inclusive teaching and learning.This paper argues that design of open plan learning environments in schools and government policy implementation must address issues of acoustic design and noise control in an effort to comply with the Australian Disability Discrimination Act 1992, the Building Code of Australia, the Disability Standards for Education 2005 and Australian Education Bill 2012. Recommendations are provided on policy changes, which will help reinforce this position across all educational spaces, from early learning centres to adult education.
Full Paper
Acoustical Quality Assessment of Lecture halls at Lund University, Sweden
Said Youssef, Rabab (1), Bard, Delphine (2), A Mahmoud, Abd El Fattah (1), Mkrm Esa, Nahed (3)
(1) National Institute for Standards, Egypt
(2) Lund University, Sweden
(3) Al-Azhar University, Egypt
ABSTRACT
Noise control in buildings should aim at reducing disturbances caused by speech noise (i.e., improve speech privacy, speech intelligibility). Room acoustics can be controlled with high room absorption, high screens and bookcases, and sufficient masking sound. This research concerns as important aspect of room acoustic metrology, the ability to quantify the most relevant room acoustic parameters for academic purposes. In this proposed study we will focus on the lecturing rooms of Lund University, of which some have designed quite recently while others were constructed many years ago. As the use of audio- visual equipment as well as the use of enabling techniques for disabled students is continuingly increasing. Lecture halls, which have not been explicitly designed for the use of such equipment, are being fitted with an assortment of audio-visual fixtures. This can lead to far less environment profoundly impacts the outcome of the learning process it is performance to assess the current state of the situation with respect to the acoustic performance of lecture halls at Lund University.
Full Paper
How to modify a tested fire-rated wall to improve its sound transmission rating, while maintaining its official fire-rated qualification
Forester, Harold
Forester Controls, Canada
ABSTRACT
Local regulatory agencies generally require wall designs that meet specific fire ratings.
acoustical consultants also have to select designs that have appropriate sound transmission properties. While most standard designs have been independently tested for both their fire and sound transmission ratings, many specialized wall designs have been tested only for sound transmission or fire resistance, but not for both. Shaft walls and walls that provide exceptionally high sound transmission loss often fit into these categories. To overcome this limitation, select a wall design that is close to the desired configuration that has been tested to the required fire rating. Then proceed to modify that design to improve its sound transmission rating, while respecting the Underwriters Laboratories design guidelines for fire ratings. For example, the UL guidelines permit the spacing between wall elements and the number of layers and thickness of gypsum board to be increased without affecting the tested fire rating. These modifications will significantly increase the sound transmission ratings. The paper presents specific examples.
Full Paper
Heavy/soft impact sound criteria and regulation in Korea
Jeong, Jeong Ho
Republic of Korea
ABSTRACT
Most of housings in Korea constructed with reinforced concrete structured high rise apartment. Floor and walls were shared with neighbors and floor impact sound generated on upper floor transmitted into lower unit. Heavy/soft impact sound is become one of social problem. In 2006, heavy/soft impact sound certification system with 4 graded rating systems mandated. 50 dB in Li,Fmax,AW; regulated in KS F 2683-2, is minimum requirement. To establish the rating system, auditory experiments on heavy/soft impact sound and field measurements were conducted. In this paper, auditory experiment results and Korean floor impact sound isolation performance certification system will be introduced.
Full Paper
Defining vehicular noise levels to manage risk associated with exterior facade design
LoVerde, John J (1), Dong, Wayland (1), Rawlings, Samantha (1)
(1) Veneklasen Associates, USA
ABSTRACT
Evaluation and mitigation of noise from vehicular sources is common as a building design criterion. In the United States of America (USA), it has been part of U.S. Department of Housing and Urban Development (HUD) multifamily building design requirements since the 1970s. It is included in numerous state and local planning requirements, and also has recently been added to various Green Building Design Standards, including school and healthcare facility design guidelines. In California, the building codes include mitigation of traffic noise sources for all multifamily and most commercial projects. These criteria specify an allowable noise level, but do not provide a method for defining this level given the statistical variations. For sources with large variations, the method of defining the level can greatly affect the building façade design and the occupant experience. Further, it may be necessary to determine this level from relatively brief measurements. This paper examines the factors that should be considered when defining the exterior noise from vehicular sources. Methods for predicting the noise level using data are evaluated, and minimum survey requirements to determine specific exterior noise parameters are suggested.
Full Paper
International proposal for an acoustic classification scheme for dwellings - Background and perspectives
Rasmussen, Birgit
Aalborg University Copenhagen, Denmark
ABSTRACT
Acoustic classification schemes specify different quality levels for acoustic conditions. Regulations and classification schemes for dwellings typically include criteria for airborne and impact sound insulation, façade sound insulation and service equipment noise. However, although important for quality of life, information about acoustic conditions is rarely available, neither for new or existing housing. Regulatory acoustic requirements will, if enforced, ensure a corresponding quality for new dwellings, but satisfactory conditions for occupants are not guaranteed. Consequently, several European countries have introduced classification schemes. The schemes typically include four classes. Comparative studies have shown significant discrepancies between countries due to national development of schemes. The diversity is an obstacle for exchange of construction experience for different classes, implying also trade barriers. Thus, a harmonized classification scheme would be useful, and the European COST Action TU0901 "Integrating and Harmonizing Sound Insulation Aspects in Sustainable Urban Housing Constructions", running 2009-2013 with members from 32 countries, including three overseas countries, had as one of the main objectives preparation of a proposal for a harmonized acoustic classification scheme. The proposal developed has been approved as an ISO/TC43/SC2 work item, and a working group established. This paper describes the proposal, the background and the perspectives.
Full Paper
Classification scheme of floor impact sounds with the standard rubber ball in dwellings
Sato, Hiroshi (1), Yoshimura, Junichi (2)
(1) National Institute of Advanced Industrial Science and Technology, Japan
(2) Kobayasi institute of Physical Research, Japan
ABSTRACT
This study presents results of subjective judgments to simulated floor impact sound to create classification scheme of heavy weight impact sound with standardized rubber ball. The floor impact sound samples were recorded in a wood-frame test house with different floor configurations and were reproduced in an anechoic chamber. Using the relationship between subjective rating and physical indices, an example of classification scheme for rubber ball impact sound measurement will be presented.
Full Paper
A new approach to building acoustics regulation in Canada
Zeitler, Berndt (1), Schoenwald, Stefan (2), Quirt, David (3)
(1) National Research Council, Canada
(2) Empa Swiss Federal Laboratories for Materials Science and Technology, Switzerland
(3) JDQ Acoustics, Canada
ABSTRACT
A new approach to the control of sound transmission is among the proposed changes in the 2015 edition of the National Building Code of Canada. The design objective is changing from a minimum STC for the wall or floor/ceiling assembly separating adjacent units to a requirement for the Apparent Sound Transmission Class (ASTC) including flanking. The approach to design is based on combining the ASTM data from conventional laboratory measurement of direct transmission through wall or floor/ceiling assemblies with measurements of flanking transmission conforming to ISO 10848 and predictions using ISO 15712-1. To support the design and regulatory approval process, the National Research Council is preparing a series of reports detailing the design procedure for a broad range of heavy monolithic and lightweight framed constructions, and providing the supporting generic data in form of web-based tools and tables from two decades of research studies in flanking test laboratories.
Full Paper
The Influence of Vibrations on Vehicle Occupant Fatigue
Azizan, Mohd Amzar (1), Fard, Mohammad (1)
(1) RMIT University, Australia
ABSTRACT
The attempts to summarize the knowledge about the human body's response to vibration, merely by introducing a physical or empirical model do not reflect a modern understanding of the effects of vibration on body comfort or fatigue. Several studies have demonstrated that fatigue leads to impairment of the ability to perform tasks. Although the performance of vehicle drivers under fatigue conditions has been investigated in many types of environments, there is insufficient research about the effects of vibration on levels of mental alertness in seated drivers. The formulation of drowsiness caused by vibration in the vehicle is complex due to several confounding factors such as vehicle interior noise and traffic control. However, understanding the effects of only vibration on drowsiness can provide significant knowledge to predict and prevent the vehicle occupant (driver) drowsiness. Hence, we investigated the relationship between whole body vibration and human drowsiness. A human vibration test setup was designed for this study. Three conditions were selected for these studies which are no-vibration condition, low frequency sinusoidal vibration and low frequency random vibration. For vibration condition, volunteers were exposed to multi-axial vibration at a frequency between 1- 15 Hz with the transmitted vibration at 0.3 m/s2 rms for 20 minutes. Changes in drowsiness level during vibration exposure were measured by recording brainwave activities along the scalp. Two brainwave spectrums (Beta wave and Theta wave) were considered for analysis. Exposure to vibration was found to be correlated with a reduction in alertness. Combined decrease in beta wave and increase in theta wave activity caused by vibrations were found to be statistically significant in sinusoidal and random vibration (p < 0.05). However, the effect of sinusoidal vibration is more pronounced compared to random vibration.
Full Paper
Automobile Power-train—Coupling Vibration Analysis on Vehicle System
Ding, Heng (1), Zhang, Weihua (1), Chen, Wuwei (1), Shi, Peicheng (2)
(1) Hefei University of Technology, China
(2) Anhui Polytechnic University, China
ABSTRACT
Engine is one of the main vibration sources, and it has a big impact on the vibration characteristics of the car. Reasonable design of suspension system can obviously reduce the vibration of automobile powertrain and the body. Aiming at the vehicle vibration induced by automobile engine, the powertrain mounting system is put into the environment of vehicle to study its coupling vibration characteristics. A multi-body dynamic model including powertrain, vehicle, body and suspension system is established to carry out the simulation calculation, then analyze the vibration transmissibility and the coupling vibration between powertrain and vehicle. The research shows that there is difference in vibration characteristics between vehicle model and six-degree-of-freedom model of mounting system. After optimizing the parameters of mounting system, the vibration transmissibility has significantly reduced, thus the vibration reduction effect has been effectively improved.
Full Paper
Study on startup transient vibration of a vehicle with 3-cylinder engine
Fu, Jianghua (1), Pang, Jian (1), Hu, Chengtai (1), Xu, Xiaomin (1), Deng, Renwei (1), Kuang, Xiaohong (1)
(1) Changan Auto Global R&D Center, China, State Key laboratory of Vehicle NVH and Safety Technology, China
ABSTRACT
The vibration of 3-cylinder engine is bigger than the 4-cylinder engine with the same engine displacement. The startup processing is studied in order to control the shake level when the engine is started. Excitation characteristics of the 3-cylinder engine is analyzed and a CAE model to analyze the startup shake is established which is verified by the test data. The possible impact factors of the startup vibration are studied and the key control methods are provided, which are applied to an case and successful results are obtained. The results show that the powerplant mounting system has a great influence on the startup vibration of the vehicle with 3-cylinder engine. Aligning the modal frequency distribution between the 3-cylinder engine mounting system and the cranking speed of the start motor, the vehicle transient shake at startup can be effectively controlled. The paper also provides a CAE simulation method which is successfully used to predict the startup shake, which provide a guideline for powerplant mounting system design at early stage of the vehicle development.
Full Paper
The Transmission of Vibration at Various Locations on Vehicle Seat to Seated Occupant Body
Ittianuwat, Ratchaphon (1), Fard, Mohammad (1), Kato, Kazuhito (2)
(1) RMIT University, Australia
(2) NHK Spring Co., Ltd, Japan
ABSTRACT
Previous research showed that vehicle seat has generally three fundamental vibration mode shapes (lateral, fore-aft, and twisting) in the frequency range below 80 Hz which is well within human perception to vibration. However, the effects of seat structural dynamics on the vibration comfort may not be captured properly by current ISO 2631-1 (1997) suggested measurement locations. Therefore, this study evaluated the current center measurement locations on seat surfaces (seat cushion and seatback foams) in assessing transmission of vibration of the occupied vehicle seat. Vibration transmissibility from vibration platform to occupant body was measured at ten different locations between human body and seat surfaces, and nine different locations on seat frame. The vehicle seat was excited in multi-direction (fore-aft, lateral, and vertical) with random vibration of 1.0 m/s2 r.m.s. for each axis over the frequency range 1 - 100 Hz. The results showed that the transmission of vibration from vehicle seat structure to human body varies with vibration mode shapes. The transmissibility was greatest at the top measurement location on the seatback surface in y-axis when seat structure undergoes lateral and twisting vibration mode shape. The transmissibility was greatest at the top measurement location on the seatback in x-axis when seat structure undergoes fore-aft vibration mode shape. The variations in transmissibility with modes of vibration and with location of measurements suggest that more than one measurement location is required to evaluate the transmissibility of vehicle seat.
Full Paper
Developing Powertrain Mounting Systems in the Virtual Engineering World Using a Full Vehicle NVH Simulator
Kennings, Paul (1), Layfield, Jonathan (1), Tarabra, Marco (1), Fothergill, David (2), Syred, Frank (3), Franks, Graham (3)
(1) Bentley Motors, UK
(2) DJ Fothergill Consulting, UK
(3) Sound & Vibration Technology, UK
ABSTRACT
At Bentley Motors, the development approach for powertrain mounts has ramped up in recent years, from Hardware based test comparisons in the early years through to our CAE based development with "Physical Simulation". This latest technique, known as the Full Vehicle NVH Simulator (FVS), allows the engineering team to physically evaluate a laboratory based vehicle with high correlation to the vehicle on road - this creates a realistic and useable link between objective data and subjective feel. The tool is powerful in that it allows the team to achieve the required attribute balance between ride comfort and powertrain NVH. Advances made towards Bentley's carbon footprint, like variable displacement engines (selectively reducing the number of active cylinders during operation), adds to the challenges of this attribute balance. This change results in lower firing orders at which mount isolation is required, making spectral tuning of the mount stiffness more challenging owing to the lower frequency nature of this operating range. The physical simulation technique which has been used for powertrain mounts development within Bentley has become a business advantage owing to the reduced number of prototypes required for testing and, therefore, reduced product development costs with accurate predictions ahead of design freeze.
Full Paper
Road noise sensitivity analysis with respect to suspension geometry
Kosaka, Fumihiko (1), Mizuno, Hiroaki (1), Inoue, Tsuyoshi (2), Takagi, Kentaro (2)
(1) Mitsubushi Motors Corporation, Japan
(2) Nagoya University, Japan
ABSTRACT
In the vehicle development, the importance of reducing road noise is increasing because of the increasing popularity of quiet electric vehicle. The suspension plays an important role on the mechanism of the structure born road noise. As the countermeasure for reducing road noise, low stiffness suspension bush is often used from the point of view of vibration insulation. However, in general, to use the low stiffness suspension bush makes the driving stability worse. From such reason, it has been difficult to achieve the compatibility between NVH and driving stability at high quality. Therefore, the other ways are required for reducing the road noise. As one of the ways, the road noise reduction by the suspension geometry is presented in this paper. In order to find the suspension geometry which reduces the road noise, the sensitivity analysis is used. For the sensitivity analysis with respect to the position of the suspension arm connecting points, the suspension model is simplified. The arms are modeled as rigid links whereas the vehicle body, tire and shock absorber are modeled as a modal model. The suspension geometry which reduces the road noise is obtained with the sensitivity analysis.
Full Paper
On the sound absorption coefficient of porous asphalt pavements for oblique incident sound waves
Bezemer-Krijnen, Marieke (1), Wijnant, Ysbrand H (1), De Boer, Andre (1), Bekke, Dirk A (2)
(1) University of Twente, The Netherlands
(2) Apollo Tyres Global R&D, The Netherlands
ABSTRACT
A rolling tyre radiates noise in all directions. Conventional measurement techniques for the sound absorption of road surfaces, however, only give the absorption coefficient for normal incidence. The absorption coefficient for oblique incidence is often computed assuming a locally reacting surface. In this paper, a measurement technique is described with which it is possible to perform in situ sound absorption measurements for oblique incidence. The measurements are performed with a small 3D microphone array. The theory behind the measurement technique is based on the local plane wave assumption. In this paper, an approach is proposed to determine whether a surface behaves as a locally reacting surface or as a non-locally reacting surface, which is an important characteristic for optimising the noise absorption properties of asphalt pavements and for modelling techniques. Preliminary measurements at various angles of incidence are performed to demonstrate this approach as well as measurements of the absorption coefficient at normal incidence to validate the microphone array technique with impedance tube measurements.
Full Paper
Comparative assessment for low-noise pavements by means of the ISO 11819 and the OBSI
Buret, Marc (1), McIntosh, James (1), Simpson, Cassandra (1)
(1) VicRoads, Victoria, Australia
ABSTRACT
In 2013, VicRoads initiated an acoustic test program for low-noise road surfaces. The program aims to assess the acoustic performance and maintenance requirements for different types of pavement surfaces over a period of at least five years. Seven different products were laid on a single section of roadway on the Mornington Peninsula Freeway in Victoria, Australia. Acoustic tests have then been carried out at regular intervals following three different methods: Statistical Pass-By (ISO 11819-1), Close Proximity Method (ISO/DIS 11819-2) and On-Board Sound Intensity method (AASHTO TP 76-10). Results from these tests are presented here. The measured performance of the different pavement is discussed and an insight is given into the comparison of the different test methods.
Full Paper
ODSURF: Optimized low noise urban road surfaces
Bérengier, Michel (1), Gusia, Peter Johann (2)
(1) IFSTTAR, France
(2) BASt, Germany
ABSTRACT
Based on results from the former project "Prediction and Propagation of Rolling Noise" developed in the framework of the German-French cooperation and during which an optimal low noise texture of dense road surface has been designed, ODSurf, financed by the French Environmental Agency and the German Federal Highway Research Institute is mainly devoted to the implementation of new technologies and materials particularly adapted for urban situations in terms of noise abatement to comply the European noise regulation. Different new solutions have been investigated. To achieve our objectives, we improved and/or developed new predicting models and experimental techniques. A particular attention has been paid on the consequences of texture, horn effect and air pumping modifications on tire-road noise emission. Theoretical approaches and new optimized road pavement designing have been carried out in parallel. Furthermore, the improvement of "conventional" wearing courses has been pursued in order to supply to end-users a complete set of low-noise solutions adapted to their own situations. First validation results are presented. Further, these new optimized pavements will be introduced in the common DEUFRABASE, previously implemented for suburban configurations, which will be completed and extended to urban situations.
Full Paper
Influence of surface textures of road markings on tyre/road marking noise
Gail, Annette (1), Bartolomaeus, Wolfram (1), Zöller, Marek (1)
(1) Federal Highway Research Institute, Germany
ABSTRACT
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
Full Paper
Assessing the acoustic properties of audio-tactile road markings
Goubert, Luc (1), Debroux, Philippe (1), Gail, Annette (2), Zöller, Marek (2), De Clerck, Kristof (3), Verleyen, Lenert (3)
(1) BRRC, Belgium
(2) FRTA, Belgium
(3) BASt, Germany
ABSTRACT
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
Full Paper
A modelling approach to spatial extrapolation of ocean ambient noise measurements
Heaney, Kevin D
OASIS Inc, Fairfax Station USA
ABSTRACT
With the growing understanding that anthropogenic ocean noise can have potential harmful impacts on the ocean ecosystem, many national environmental agencies are beginning to grapple with the task of assessing the levels of ambient noise in their regional waters and an understanding of these impacts. The challenge facing national regulatory agencies, in particular European Union Member States, which are now required to come up with a plan for assessing the environmental health of their waters, is to use limited resources intelligently to estimate the overall impact of man-made sounds. In this paper, we present an efficient modeling approach for low-frequency sound and a way forward for incorporating measurements into an environmental assessment framework.
Full Paper
Patch near-field acoustical holography based on vector hydrophone array
Hu, Bo (1), Yang, Desen (1), Shi, Shengguo (1), Shi, Jie (1), Sun, Yu (1)
(1) Harbin Engineering University,China
ABSTRACT
Near-field acoustical holography is a powerful tool for identifying noise sources from partially known sound pressure field. Patch near-field acoustical holography (PNAH) is related to the partially measured pressure on the hologram surface in terms of sampling and bandlimiting matrices, which cost more in computation. PNAH procedure based on measuring of vector hydrophone array is described, including the mathematical formulation. The measurement array can been smaller than the source, thus the practicability and efficiency of this technology is greatly enhanced. Then an experiment has been carried out with vector hydrophone array. The experimental results have illustrated the high performance of PNAH and the advantages of a vector hydrophone array in an underwater near-field measurement.
Full Paper
Characterising the acoustic footprint of Australia\'s new research vessel RV Investigator
Kloser, Rudy (1), Martin, Tara (1), Sherlock, Matt (1)
(1) CSIRO, Australia
ABSTRACT
The RV Investigator is Australia's new noise quietened Marine National Facility (MNF) vessel built to comply with the DNV silent-R specification. This radiated noise specification was based on the ICES 209 CRR specification designed with the main goal of minimising vessel avoidance for fisheries surveys. Noise quietening was specified for RV Investigator to improve the acoustic detection of instruments and reduce the vessel's noise footprint on the environment for research activities. Traditionally DC propulsion motors are used to achieve radiated noise compliance; in this case AC propulsion motors have been used. Initial noise measurements show the RV Investigator is 20 dB (factor of 100) quieter than the previous MNF vessel, RV Southern Surveyor which will significantly improve acoustic instrument performance. The new acoustic systems on the RV Investigator range from sub-bottom profilers, Doppler current profilers, multi-frequency and multi-beam water-column echo-sounders and low to mid frequency multi-beam bathymetry echo-sounders.
Full Paper
Modeling ocean noise on the global scale
Porter, Michael B (1), Henderson, Laurel J (1)
(1) Heat, Light, and Sound Research, USA
ABSTRACT
In recent years there has been a much greater interest in understanding noise in the ocean. In Europe this interest is tied to the Marine Strategy Framework Directive, which seeks to maintain 'good environmental status' with specific attention to sound. In the U.S. a similar commitment was made to evaluate and improve tools for assessing the impacts of human-induced noise in the ocean. In earlier work we did extensive modeling of soundscapes in the U.S. EEZ to understand the various layers of sound. Pile driving, seismic surveys, shipping, and sonar exercises were all considered. In this work, we are extending this modeling to the global scale. The global scale presents unique and interesting challenges in terms of the computational modeling. We discuss the approach and present preliminary results characterizing the global soundscape.
Full Paper
Marine Soundscape Ecology
Sydney, Harris (1), Radford, Craig (1)
(1) University of Auckland, New Zealand
ABSTRACT
In the face of accelerated climate change, monitoring biodiversity has become a critical task for ecologists. Habitat loss is occurring at an alarming rate both in terrestrial and marine ecosystems, resulting in endangerment and extinction of species up to 1,000 times faster than natural rates. However, traditional biodiversity measurements are logistically and financially difficult, making biodiversity monitoring a challenging obstacle to conservation efforts. In terrestrial environments, "Soundscape Ecology" has recently emerged as a potential solution to these problems, providing a mechanism for measuring biodiversity at various temporal and spatial scales using acoustic signatures. Several acoustic diversity indices have proven to be useful indicators of biodiversity in a variety of landscapes. Thus far, this technique has not been extended to marine environments. What is known is that different marine habitats have distinct sound signatures both in temperate and tropical waters. For example, studies have shown that temperate reefs from within a marine reserve have a different spectral signature compared to reefs outside the reserve. Also, a fringing reef from a tropical island has a different spectral signature to those of the lagoon and back reefs. Here we highlight the research potential for using acoustics to monitor marine biodiversity and what is required for this field to progress.
Full Paper
Using low cost single-board microcontrollers to record underwater acoustical data
Travaglione, Ben (1), Munyard, Andrew (1), Matthews, David (1)
(1) DSTO, Australia
ABSTRACT
Over recent years there has been a rapid increase in the availability of single-board microcontrollers. In this paper we review three such microcontrollers; the Arduino Mega2560, the Raspberry Pi and the Beaglebone Black. We show how these devices can be used to produce low cost, low power, deployable, configurable at-sea measurement systems. We also highlight the advantages and disadvantages of each type of single-board microcontroller. We show how these devices can be configured to acquire either digital or analog data from a variety of sensors, as well as process, store and transmit the results. We present some results of high sample rate analog recordings which have been obtained at a fraction of the cost of the more common commercial alternatives. We also highlight some of the pitfalls associated with using these leading-edge devices.
Full Paper
Soundscape Study of Urban Public Spaces along the Sea Shore
Kabilan, Tharangini (1), Mohan, Anjana (1), Jeyachandran, Keerthika (1), Ramasamy, Kalaiselvi (2)
(1) Rajalakshmi School of Architecture, India
(2) School of Planning and Architecture - Vijayawada, India
ABSTRACT
The cities are profound with variety of sounds that keeps fluctuating at different time intervals. However one restless source lying on the border of Chennai city, India is the wave sound of Marina Beach. It is one of the important urban public spaces that attract number of visitors every day. To carry out the soundscape study of Marina Beach, a stretch perpendicular to the sea comprising of three levels - the Traffic road, a linear double rowed vendor shops and the seashore is chosen. Sound walk followed by a questionnaire study is carried out at each level to investigate the transition of sound along the stretch. Psycho-physical data analyses of verbal descriptions expressed by respondents at each level are observed to be different. The Leq levels are found to be varying throughout the day and found to record the values of about 70 - 80 dB(A) at peak hours, measured using Norsonic sound level meter type 118. The role of vendor shops in providing acoustical aid to the transition from traffic noise to wave sound was mapped for the stretch. Based on the subjective surveys few recommendations are discussed in the full paper to improve the soundscape of the seashore.
Full Paper
Analysis of soundscape of selected urban public places and its impact on their assessment by users
Kamenicky, Matej
Czech Technical University, Czech Republic
ABSTRACT
This paper describes an ongoing research project concerning the soundscape of urban public spaces and the relevance to architectural quality of particular public spaces and their overall assessment by users. Described here is the methodology of data gathering and analysis that was carried out last year in Prague, Split and Ljubljana. In addition, partial and expected results and possible further applications will be discussed. The topic of the research is the effect of sound environment on perceived quality of a given public space by the inhabitants and the dependant factors that influence these relations. The research is focused on selected public spaces representing different typological categories in cities of different geographical location and their users' cultural background. Examined cities will represent regions of central Europe, south Europe and north east Australia.
Full Paper
The Urban Park Soundscape in Mountainous Cities:A case study in Chongqing
Li, Heng (1), Xie, Hui (1), Kang, Jian (2)
(1) Chongqing University, China
(2) Sheffield University, UK
ABSTRACT
As a typical mountainous city, undulating terrain in Chongqing creates a unique urban structure, and the richness of urban park soundscapes is enhanced as well. In this paper, one urban park, named 'ShaPing Park', was selected for the field measurement and questionnaire survey. Approximately 10 receiver points were arranged, with the consideration of both elevations and functional zones. The recreation zone and quiet zone were generally dominated by low frequency sounds, whereas the middle frequency sounds were more significant at the activity zone. Some special sounds, such as whipping tops, were observed in the park. People singing (65.1%) was the most annoying sound due to its unpleasantness. 57.2% of the respondents considered the acoustic environment as severely or relatively noisy, but only 44.5% of the interviewees regarded it comfortable or relatively comfortable. 'Sound level' (57.1%) and 'personal interests' (49.2%) were recognized as the major factors influencing personal sound preference, and the appropriate improvements of acoustical environment were identified as the priority in the studied urban park.
Full Paper
Withdrawn1
Withdrawn1,
ABSTRACT
Withdrawn1
Withdrawn9
Withdrawn9,
ABSTRACT
Withdrawn9
Cost reduction of noise treatments in the oil & gas industry - design of noise mitigation for gas compressor stations using engineering optimisation
Davis, David James
URS, Australia
ABSTRACT
The capital cost of noise control treatments for land-based gas compressor stations can be significant. Field gas compression facilities can have many noise sources including compressors, fan coolers, power generators or transformers, pipes and valves, flares and so on. Some coal seam gas field facilities can also have co-located water treatment plant or water transfer pumps. Environmental noise computer modelling predictions can estimate the component contribution noise emissions from each individual noise source at each affected receiver. Using these data, an experienced practitioner can estimate a scheme of noise level reductions for each source so that the noise emissions of the entire site comply with the overall environmental noise targets at the receptors. However it is not straightforward to select and design the noise control treatments for all of the individual noise sources with the explicit goal of minimising the total capital cost for the overall noise mitigation program. This paper provides an example of minimising the cost of noise control treatments required for a coal seam methane gas field compression station using two different engineering optimisation techniques.
Full Paper
Design for noise mitigation measures for public housing developments in Hong Kong
Lo, David (1), Yim, Stephen (1), Leung, Kenneth (1)
(1) Hong Kong Housing Authority, Hong Kong
ABSTRACT
Hong Kong is renowned for its high density living where we commonly find residential developments, including public housing developments, located close to roads with heavy traffic. To protect the residents from noise nuisance, the Hong Kong Housing Authority (HKHA) has applied a series of noise mitigation measures including low noise road surfacing, noise enclosures/barriers, building setback, orientation and vertical fins etc., to reduce the noise impact. Where the impact is found too severe for the above noise mitigation measures to be adequate, we need to develop more innovative building design to improve the building efficiency and enhance the built environment. In this paper, we share our experience in the research and development of innovative building design to mitigate noise problems. We also give an account on how the noise challenges are tackled in recent projects by making use of the above measures plus innovative designs such as acoustic balcony and acoustic window.
Full Paper
Investigation of sound insulation for a Supply Air Window - field measurements and occupant response
Søndergaard, Lars Sommer (1), Legarth, Søren Vase (1)
(1) DELTA, Denmark
ABSTRACT
The Danish Environmental Protection Agency's guideline from 2007 "Noise from roads" introduces noise limits with open windows for certain situations. With a moderate/high outdoor noise level from traffic, railway or industry these noise limits cannot be complied with for regular windows, but requires windows with better sound insulation in open position. The window investigated in this project is a double window construction consisting of an outer part, with a top hung vent in the lower part of the window, and an inner part, with a bottom hung vent in the upper part of the window. The first parts of the project consisted primarily of laboratory measurements investigating the influence of different combinations of e.g. dimensions, opening area and the use of absorbing material. In the second part of the project the window type were installed in 14 flats exposed to approximately 71 dB noise levels from road and railroad traffic. Measurements were performed satisfying the indoor noise limits. The measurements were followed by a questionnaire. The occupants generally responded that the windows allowed them opportunity to have open windows without being especially annoyed by the noise; however other functionalities of the windows were not always acceptable.
Full Paper
Tackling Traffic Noise Through Plenum Windows - An Application in Hong Kong
Yeung, Maurice (1), N G, Isaac (1), Lam, John (1), Tang, Shiu Keung (2), Lo, David (3), Yeung, David (4)
(1) Assessment and Noise Group, Environmental Protection Department, The Hong Kong Special Administrative Region Government People\'s Republic of China
(2) Department of Building Services Engineering The Hong Kong Polytechnic University Hong Kong People\'s Republic of China
(3) Hong Kong Housing Authority The Hong Kong Special Administration Region Government People\'s Republic of China
(4) Environ Corporation, Hong Kong
ABSTRACT
Hong Kong is a very small but hyper-dense city with over 7 million living in 1,100 sq km in which 85% of land is hilly area. Like other metropolitan cities, Hong Kong is facing significant road traffic noise problems. The Government of Hong Kong is committed to addressing road traffic noise problems and has adopted proactive actions like preventing the problems through land use planning and environmental impact assessment process for new roads, implementation of appropriate mitigation measures on existing roads etc. In most cases, measures like roadside barriers / enclosures would be required. However, the majority of residents live in high-rise buildings and such compact urban forms setting would easily be susceptible to road traffic noise problem. To make Hong Kong a livable place with a good acoustic environment, examining other measures on building façade design is necessary. This paper will discuss on the actual application and in-situ tests conducted for plenum type windows in its application at a housing development next to a heavily trafficked road. With careful design and use of absorptive materials, a noise reduction of up to 8 dB(A) can be achieved without compromising sufficient air ventilations meeting local regulations.
Full Paper
New insights into perception of aircraft and community noise events
Adams, Keith
B&K EMS, Australia
ABSTRACT
The current practice of basing all noise monitoring on A-weighted day/night levels has often been criticised. Questions as to what is really happening in the "noisescape" have been raised, with consequences for managing complaints and future planning. At the same time, some permanent noise monitoring terminals are now available to record simultaneously A-weighted, C-weighted, Z-weighted, stationary loudness, non-stationary loudness, and effective perceived noise levels of noise events. These data, together with other available functions in permanent monitors such as dominant pitch, frequency percentile measures and neural network source characterisation, provide useful resolutions of the more complex events that are not purely due to aircraft. The collection of two years of continuous records of all of these parameters with audio, from a modified permanent airport noise monitor, that is exposed to a variety of community, traffic and aircraft sounds, provides a valuable data set for further study. In particular, event-threshold parameters, maximum levels and exposure levels based on the perception metrics, in comparison with the common A-weighted metrics, have been obtained. Together with recordings from some other sites, new insights into what is really happening in noise events are presented.
Full Paper
Stated choice valuation of aircraft noise and other environmental externalities at Bangkok Suvarnabhumi Airport
Cheramakara, Narudh (1), Bristow, Abigail (1), Budd, Lucy (1), Zanni, Alberto (1)
(1) Loughborough University, UK
ABSTRACT
Aircraft noise and other environmental externality effects have gained significant public attention in Thailand since Bangkok's Suvarnabhumi Airport opened in 2006. Residential areas around the airport are expanding rapidly and local residents are protesting about the noise and air pollution from the airport. This study employed Stated Choice to elicit willingness-to-pay (WTP) values to reduce aircraft noise and air pollution. The novelty of the research arises from the fact that it explores monetary values of externalities not only for those who suffer from the pollution (residents) but also those who have some responsibility for the externalities that are created (i.e. air passengers). Results indicate that passengers and residents have different priorities in terms of aviation externalities. As might be anticipated, residents place a higher value on aircraft noise nuisance than passengers at 104.76 USD and 70.63 USD per year respectively to halve aircraft noise levels. In terms of air pollution, passengers had a higher WTP at 151.18 USD against residents' WTP of 86.52 USD per year to halve local air pollution created by aircraft. Passengers are willing to pay 41.69 USD per year to offset carbon emissions. The study found that aviation growth at Suvarnabhumi was underestimated and there is an urgent need to implement environmental mitigation policies to address the issue.
Full Paper
The impact of civil versus military aircraft noise on noise annoyance
Gelderblom, Femke B (1), Gjestland, Truls (1), Granøien, Idar L N (1), Taraldsen, Gunnar (1)
(1) SINTEF, Norway
ABSTRACT
The noise characteristics of civil and military aircraft operations differ significantly. For example, the difference in flyover noise from a fighter aircraft and jet plane is easily heard. Civil traffic also tends to be spread out relatively evenly over a day, whereas military training operations can often be characterized by short periods of high activity followed by long periods of comparative silence. Such clearly noticeable differences are disregarded in commonly used noise dose indicators, but may be expected to significantly affect noise annoyance levels within a community. Therefore, an attitudinal survey was conducted by means of telephone interviews in the vicinity of the airports of the Norwegian cities Trondheim and Bodø. While those living near Trondheim's airport are predominantly exposed to noise from civil air traffic, Bodø has a runway that is shared by the city's civil airport and a military airbase. The focus of the study was not on demographic factors, which is typical for an attitudinal study, but instead on acoustical and operational aspects. This study is part of an ongoing research project with the aim of explaining why observed dose-response relationships differ widely from one community to the next.
Full Paper
Relaxations of operating restrictions on Noise and resident\'s reaction at Narita International Airport
Ogata, Saburo (1), Shinohara, Naoaki (2)
(1) Narita International Airport Corporation, Japan
(2) Narita International Airport Promotion Foundation, Japan
ABSTRACT
At Narita International Airport, air traffic movements have been controlled under various noise related operating restrictions as well as to conform to agreements with residents around airport so as to minimize noise impact because the airport is located inland. In response to needs for airport capacity expansion, Narita International Airport Corporation and Ministry of Transport have had to relax some such restrictions to ensure safety and to improve operating efficiency. This paper makes a brief review of noise mitigation measures at Narita, describes measures to cope with relaxation and resident's reactions like noise complaints and examines the effectiveness of the relaxation. Especially, it speaks about current situation after the enforcement of night curfew relaxation, which came into operation since March 31 last year.
Full Paper
The next generation of supplementary aviation noise metrics and their use in managing aviation noise.
Porter, Nicole (1), Knowles, Andy (1), Fisher, Nick (2), Southgate, Dave (3)
(1) Anderson Acoustics, UK
(2) Department of Infrastructure and Regional Development, Australia
(3) Independent Consultant, Australia
ABSTRACT
Successful aviation noise management and sustainable airport development relies on describing noise exposure effectively, understanding its impacts, and communicating these effectively. We need the right tools to describe noise and its impacts in a meaningful way. Furthermore, decision makers need a balanced scorecard to make informed decisions based on the outcomes from an appropriate suite of analysis tools. This paper summarizes our previous work which examined the limitations of traditional noise contours for describing noise exposure based on long-term averages and considered a more targeted contour based on shorter-term noise measures. It looks at supplementary ways of describing the physical exposure to aircraft noise events including those developed in Australia in 2000. These are revisited and we will show in our presentation, by using recent case examples, how we have applied and/or refined them using GIS techniques. We also highlight key information from our companion paper on aircraft noise effects on health and its monetization. All these elements are required for effective management of aviation noise.
Full Paper
The economic value of aircraft noise effects: a UK perspective
Sanchez, Diana (1), Berry, Bernard (2), Knowles, Andy (1)
(1) Anderson Acoustics, UK
(2) BEL - Environmental, UK.
ABSTRACT
The quantification of the effects of aircraft noise on health and quality of life and the associated monetisation of those effects has taken on significance as a major field of study with important implications in policy making and business management. Good quality studies have been conducted in this matter. Although these studies have enriched the understanding of the magnitude and complexity of this matter, several gaps remain, challenging decision making on aircraft noise management at macro and micro levels. This paper is part of a series of papers on understanding and communicating the exposure to, and impacts from aviation noise and developing a balanced scorecard for informed decision-making. In particular, this paper aims to provide an overview of the most up to date and robust monetisation methodologies and the context for its application to UK aviation policy. It presents some estimates for London Airports to show the change in the cost of aircraft noise effects on health and annoyance over 5 years. We suggest a set of principles and a process that can guide monetisation efforts of aircraft noise effects. We argue that monetary values should be considered as indicative and should only be used to understand trends rather than quantify the effects in an absolute sense.
Full Paper
Continuous Descent Approach (CDA) compared to Regular Descent Procedures: Less Annoying?
White, Kim (1), Arntzen, Michael (2), Bronkhorst, Adelbert (3), Meeter, Martijn (4)
(1) National Aerospace Laboratory NLR, The Netherlands / VU University Amsterdam, The Netherlands
(2) National Aerospace Laboratory NLR, The Netherlands / TU Delft, The Netherlands
(3) TNO, The Netherlands / VU University Amsterdam, The Netherlands
(4) VU University Amsterdam, The Netherlands
ABSTRACT
Annoyance reactions to different types of landing procedures were addressed in a controlled laboratory setting using a Virtual Community Noise Simulator (VCNS) with a head mounted display. Participants, standing on a virtual countryside road, experienced four types of descent flyovers by an A330 aircraft: a regular descent flyover at 2000ft and CDAs at respectively 3000, 4000 and 5000ft. These types of landing procedures are representative of flights approaching Amsterdam Airport Schiphol (AAS) in the Netherlands. Sound recordings for the VCNS were made on a countryside road and adjusted to match the indicated altitudes. After each flyover, participants were asked to rate their noise annoyance during the previous minute. Preliminary results showed that the 3000ft CDA was rated as the most annoying, followed by the ratings of the regular landing procedure and higher CDAs. These results could indicate that a CDA procedure, despite having lower LAmax and similar SEL levels, may still reach higher annoyance ratings due to longer flyover durations.
Full Paper
Adapting an MSE controller for active noise control to nonstationary noise statistics
Barkefors, Annea (1), Sternad, Mikael (1)
(1) Uppsala University, Sweden
ABSTRACT
In feedforward active noise control, a primary noise signal is used to generate control signals via a set of loudspeakers. In problems where many loudspeakers are used, it becomes difficult to adjust the controller filters to fast changing spectral properties of broadband primary noise signals. Many parameters then need to be readjusted simultaneously, which limits the tracking performance of e.g. filtered-x LMS adaptation algorithms. Here we propose and evaluate two feedforward control methods based on linear quadratic gaussian control that adapt to the often time-varying statistical properties of the feedforward noise signal, in a partly indirect adaptive design. For both proposed methods, the time is divided in batches and the control laws are updated for each time batch based on repeated estimates of the noise statistics. In the first method, the estimates of the noise statistics are incorporated into the controller, which is updated for each batch, whereas in the second method the controller is kept constant and a predictor for the noise is updated. The first method seems promising, and shows a gain in attenuation of about 5 dB over a controller that disregards the feedforward noise statistics. The second method, however, shows no such advantage.
Full Paper
Multivariable control of tonal disturbances using minimization of the maximum error signal through adaptive error signal weighting
Cheer, Jordan (1), Daley, Steve (1)
(1) Institute of Sound and Vibration Research, UK
ABSTRACT
In many multichannel active noise and vibration control systems the controller is adapted to minimize the 2-norm of the error signals. This may, however, lead to a large spatial variance in the residual error. A method of achieving a more uniformly controlled error field using a weighted squared error strategy has previously been proposed, although the presented method of defining the error weighting parameters results in a very slow convergence rate. This convergence rate limitation has been overcome by the minimax algorithm which minimizes, in a least-squares sense, the maximum error signal at each iteration. However, due to the inherent switching in this algorithm, for fast convergence speeds it suffers from significant misadjustment and in a tonal control problem this introduces additional unwanted spectral components. In this paper an alternative method of minimizing the maximum error signal is proposed which uses an adaptive error-weighting matrix that is bounded and so avoids the slow convergence speeds previously reported. It is also shown that the pro- posed algorithm does not suffer from the same misadjustement problems shown by the minimax algorithm. The details of the proposed method are first outlined and then its performance is compared to the previously proposed methods through a series of time-domain simulations employing measurements of a physical sys- tem.
Full Paper
Adaptive feedback noise control with leaky FeLMS algorithm
Chen, Kai (1), Paurobally, Roshun (2), Pan, Jie (2), Qiu, Xiaojun (1)
(1) Key Laboratory of Modern Acoustics and Institute of Acoustics, Nanjing University
(2) School of Mechanical and Chemical Engineering, the University of Western Australia
ABSTRACT
In this paper, an adaptive feedback control algorithm for ANC (Active Noise Control) with leaky FeLMS (Filtered-error Least Mean Square) algorithm is proposed. A shaping function is used in the updating equation, which selects the frequency band of the noise attenuation for the ANC system. Compared with the adaptive feedback ANC structure based on traditional FxLMS (Filtered-x Least Mean Square) algorithm, the effects of the proposed algorithm are focused only on the selected band and interference from other frequency bands, which can induce instability, can be reduced significantly. The RF is only applied on the updating process for the coefficients of the control filter rather, so the proposed algorithm does not introduce any extra delay. In this paper, the proposed algorithm is analyzed and it is proven to be suitable for applications where broadband noise is present, but the targeted band is limited to a narrow band.
Full Paper
Active sound design for a passenger car based on adaptive order filter
Lee, Sang Kwon (1), Lee, Seung Min (1), Kang, In Deuk (1), Shin, TaeJin (1)
(1) Inha University, South Korea
ABSTRACT
The paper presents an adaptive order filter for the sound design of a passenger car. The engine speed is calculated by using the pulse signal detected at engine speed sensor such as cam shaft position sensor (CSPS) or engine ignition position sensor (EIPS). Nowadays, the pulse signal of engine speed is delivered to the engine management control unit (ECU) system. The ECU supplies the engine speed data to the display throughout a high speed gateway. The ANC system can also use this data for the generation of reference signal. Most of reference signals used for the noise control of an engine are the sine wave at the instant frequency (rpm/60). This sine wave is discretely changed with the increment of engine speed but not continuous. Therefore, the ANC system using this reference cannot work when the engine speed is changed rapidly form 1000rpm to 6000rpm but work well at the fixed rpm. In this paper new adaptive order filter (AOF) for the ANC system of interior noise of a car is proposed. The new algorism uses the continuous reference signal instead of the sine wave. This ANC system is also applied for the active sound design (ASD). The AOF is very excellent algorithm for the ASD of a vehicle.
Full Paper
A modified frequency domain adaptive filter for active noise control
Lu, Jing (1), Nirong, Li (1), Ning, Han (2)
(1) Nanjing University, China
(2) Southeast University, China
ABSTRACT
Frequency domain adaptive filter has potential benefits of fast convergence and low computational load, which make it attractive in the application of active noise control. However, it has been noticed that the commonly used normalized frequency domain block LMS algorithm faces the problem of deterioration of steady-state behavior when the whole control system is noncausal or the adaptive filter is of deficient length. In this paper, an efficient modification of the frequency domain block LMS algorithm is described, and it can be theoretically proven that the proposed algorithm can unconditionally converge to the optimal Wiener solution. Moreover, the convergence behavior is also discussed. The experiment in a short duct active noise control system clearly demonstrate the superiority of the proposed algorithm.
Full Paper
Active control of vehicle powertrain noise using inverse model LMS algorithm
Sun, Guohua (1), Feng, Tao (1), Li, Mingfeng (1), Xu, Ji (1), Lim, Teik C (1)
(1) University of Cincinnati, USA
ABSTRACT
Current active noise control (ANC) technology cannot yield a balanced performance over broad frequency range when applied to powertrain noise control. It is because most of these ANC systems are configured with the traditional filtered-x least mean squares (FXLMS) algorithm with an inherent limitation in the frequency-dependent convergence behavior. In particular, the phase delay of the secondary path in the FXLMS algorithm will significantly affect the convergence speed and thus lead to a relatively poor tracking ability for the transient event. In this study, a novel inverse model least mean square (IMLMS) algorithm is proposed for active powertrain noise control system with an enhanced convergence speed in order to better track the variation of noise signatures due to unavoidable change in the engine speed. The IMLMS algorithm is realized by utilizing the inverse model of the secondary path to minimize the effect of its dynamics on algorithm's convergence to gain a significant improvement in the convergence speed and tracking ability. Numerical simulation using measured powertrain noise responses is also performed to demonstrate the effectiveness of the proposed algorithm. Results show obvious improvement in the convergence speed and appreciable noise reductions over a broad engine rotational speed range.
Full Paper
Stereo or binaural headphones for sound location
Cohen, Graeme J
Valve Research Pty. Ltd., Australia
ABSTRACT
Stereo sound is reproduced over two spaced apart loudspeakers. When headphones are used in place of loudspeakers the stereophonic space is incorrectly reproduced. Stereo headphones could arguably be called binaural headphones, that is the left sound source being heard in the left earphone only. In a live situation of sound the human head hears the sound with both ears. When using headphones and two microphones the sound is different and may not have accurate location in space. By using a cross feed of sound, left to right and right to left, and using suitable compensation and delay, it can be shown that a natural and accurate location of sound source, music, noise etc. may be accomplished. A cross feed system has been developed using previous work, with references. A sound source and delay system has been developed to give a measure of the source using headphones. This technique can be used for use with microphones and recording media, using headphones as a human interface. This is used, with two sound level meters, and computers, for accurate sound source position by using controlled cross feed, amplitude, delay etc. within the frequency band measured. Headphones being used as a live check of the recording.
Full Paper
Noise Reduction Measures of Noisy Kitchen Devices and Evidence of their Improvement by an Objective Analysis of Spontaneous EEG Measurements
Fischer, Martin (1), Spessert, Bruno M (1), Emmerich, Edeltraut (2)
(1) Ernst-Abbe-University of Applied Sciences Jena, Germany
(2) Jena University Hospital, Germany
ABSTRACT
In modern life, influence of noise becomes more and more important. Especially at home, Europeans desire a quieter kitchen. In general small, electromotive-driven appliances and in particular blenders can generate inconvenient home noise emission. Noise excitations of these devices were diagnosed experimentally. On this, constructions were applied to modify noise emission. The modified noise emissions were compared in terms of sound power level and psychoacoustic parameters like loudness, sharpness and roughness. In order to analyze objectively the psycho-physiological stress caused by these noises, a spontaneous EEG experiment was conducted. "Original noise" of the device and modified "optimized noises" were taken as experimental stimuli. Impact of the noises on psycho-physiological stress of experimental subjects (n = 20) were measured by spontaneous EEG. Through power density distribution, evidence on significant differences between "original noise" and "optimized noises" were found. The power density distributions of the "optimized noises" as compared to the "original noise" come closer to the distribution when subjects are relaxed-awake. This showed that the modifications have been successful as measured through an objective mean.
Full Paper
Effect on car interior sound quality according to the variation of noisy components of tire-pattern noise
Shin, Sung-Hwan (1), Hashimoto, Takeo (2), Hatano, Shigeko (2)
(1) Kookmin University, Korea
(2) Seikei University, Japan
ABSTRACT
A tire noise is one of the important noise sources of vehicle. Especially, it becomes more dominant one for motor-driven vehicle such as electric or hybrid vehicle. The purpose of this study is to grasp the effects of the variation of noise components of tire-pattern noise on car interior sound quality. To this end, tire noises were recorded with a compact car but with different types of tire pattern. Noisy components of each tire noise were indicated and then the noisy components were modified with their peak level, half-power bandwidth, and position on frequency domain. By employing subjective listening tests whose target was to evaluate the extent of annoyance of the modified noises, the change tendency of annoyance according to the variation of the noisy components was investigated and an index was proposed that could estimate and predict the annoyance of tire-pattern noise. In addition, it was known that energy ratio of a noisy component to background noise in the frequency range that the noisy component exists was one of the important descriptors representing the annoyance of tire-pattern noise.
Full Paper
Rhythmic constant pitch time stretching for digital audio
Trevorrow, Brendan
University of Southern Queensland, Australia
ABSTRACT
Constant pitch time stretching is not uncommon in audio editing software, however several issues arise when it is used on musical recordings, most notably the doubling and skipping of rhythmic transients. This paper examines three signal processing algorithms which are commonly used to provide constant pitch time stretching: these are SOLA (Synchronous Overlap and Add), TD-PSOLA (Time Domain Pitch Synchronous Overlap and Add), and Phase Vocoder. Enhancements to the SOLA and TD-PSOLA algorithms are provided which may make them more suited to rhythmic music. It is found that each of these three algorithms introduce audible artifacts in the time stretched waveform, the severity of these side effects and what causes them is also discussed.
Full Paper
The influence of the sensation of rhythm on comfort and productivity
Yamaguchi, Masao (1), Hanawa, Kazuto (1), Toi, Takeshi (1)
(1) Chuo University, Japan
ABSTRACT
Recently, an evaluation of stress and comfort by using physiological information has been being researched as a quantitative and objective evaluation method. Moreover, sounds which improve productivity introduced into an environment where people work are in demand. In this research, first, to investigate comfortable rhythmical sounds, we conducted a sound quality evaluation, by a subjective evaluation as well as the objective evaluation that used heart rate and salivary amylase. We prepared two sounds: rhythmical sounds which were a metronome sound and an operation sound emitted by a multifunctional peripheral (MFP). From these results, it may be stated that subjects felt more comfortable when they heard a rhythmical sound whose rhythm was a little slower than their heart rate. Moreover, it may be stated that it is possible to evaluate the influence of the sensation of rhythm on comfort by using heart rate and salivary amylase. In the second evaluation, the subjects calculated two-digit number additions, with the presentation of the metronome sound and the operation sound emitted by the MFP used in the first evaluation. Consequently, the number of calculations per minute increased when they heard a rhythmical sound whose rhythm was a little faster than their heart rates.
Full Paper
Attenuation of acoustic resonances in an inclined open cavity using Micro Perforated Panels
Gonzalez Diaz, Cristobal (1), Ortiz, Santiago (1), Cobo, Pedro (1)
(1) Consejo Superior de Investigaciones Cientifical, Spain
ABSTRACT
Airframe noise is equal to or louder than engine noise during the landing approach of a commercial aircraft. Cavity noise is one of the most important airframe noises. When airflow passes over an open cavity, due to vortex shedding at the upstream edge of the cavity and the geometry of the cavity, high-level aero-acoustic noise may be generated. When the incident acoustic waves produced by the airflow couples with the acoustic cavity resonances intensive tones are generated in and around the cavity at resonant discrete frequencies. Sound radiation due to the acoustic cavity resonances in an open cavity could be achieved by passive means such as lining the walls with absorbent materials. Porous and fibrous materials are used where there is no airflow. However, in presence of airflow, Micro Perforated Panels (MPP) and Porous metals are employed instead. This paper presents experimental and simulated results of the attenuation of acoustic cavity resonance tones in and around of an open cavity without and with inclined walls with lined Micro Perforated Panels.
Full Paper
Self-noise prediction of a sharp-edged strut using a quasi-periodic CFD-BEM technique
Karimi, Mahmoud (1), Croaker, Paul (1), Kessissoglou, Nicole (1), Doolan, Con J (2), Marburg, Steffen (3)
(1) UNSW Australia, Australia
(2) University of Adelaide, Australia
(3) Universitat der Bundeswehr Munchen Werner, Germany.
ABSTRACT
The self-noise generated by a sharp-edged strut immersed in low Mach number flow is predicted using a hybrid computational fluid dynamics (CFD) - boundary element method (BEM) technique. The fluctuating flow field is obtained using an incompressible CFD solver. A high-order reconstruction scheme is used to extract acoustic sources based on Lighthill's analogy from the flow field data. Acoustic waves generated by these flow noise sources propagate to and are scattered by the trailing edge of the strut. A BEM model of the sharp-edged strut, based on the Burton-Miller formulation, is used to predict the scattered sound pressure. A quasi-periodic technique is implemented in the BEM model so that the sound generated by the entire span of the strut can be predicted by modelling only a small spanwise segment. The results from the hybrid CFD-BEM technique are presented for turbulent flow past a sharp-edged strut, with Reynolds number based on chord Rec=2.0×105 and Mach number M=0.044. The computed aerodynamic and acoustic results are compared with experimental data obtained using the anechoic wind tunnel at the University of Adelaide.
Full Paper
Estimation of pressure fluctuations in a turbulent boundary layer based on vibro-elastic models
MacGillivray, Ian (1), Skvortsov, Alex (1)
(1) DSTO, Australia
ABSTRACT
A simple, but scientifically rigorous, framework is proposed for estimation of effectiveness of elastic materials for the reduction of pressure fluctuations. The framework employs the intrinsic correspondence between a transformation of vorticity perturbations into acoustic waves at the elastic boundary and the conversion of transverse (shear) waves to radiated longitudinal (pressure) waves. The case of a significantly subsonic wall flow (such as a turbulent boundary layer) is considered and the relative effect of elastic boundaries on the turbulent pressure fluctuations is estimated. The framework does not allow calculation of the absolute radiation levels, but is reasonably straightforward to implement in comparison to full-scale CFD and aero- elasticity models, and is not computationally intensive. The proposed approach enables rapid estimation of numerous 'what-if' scenarios that become important for design of new vibro-absorbing materials and for prototyping studies.
Full Paper
Effects of Hydrodynamic and Acoustic Pressure Fluctuations on Transmitted Sound in Wavenumber-Frequency Domain
Okutsu, Yasuhiko (1), Hamamoto, Naoki (1)
(1) Mitsubishi Motors Corporation, Japan
ABSTRACT
To control flow induced noise such as vehicle interior noise is very important for product development. In transmitted sound induced by flow field, a near acoustic field has to be considered. In this study, the wavenumber-frequency spectrum method was applied to the flow field around a square cylinder placed near a flat plate in order to examine pressure fluctuations in the near acoustic field. Since pressure fluctuations there contain both acoustic and hydrodynamic fluctuations, to deal with transmitted sound, both pressure fluctuations and structural bending waves have to be considered in this study. The flow field has been investigated by applying Computational Fluid Dynamics (CFD) based on the Lattice Boltzmann Method (LBM). The wavenumber-frequency spectrum was calculated by pressure fluctuations from CFD results. Thus, pressure field were investigated in wavenumber domain, and pressure fluctuations which contribute effectively to radiate the transmitted sound were extracted from all of them. As a result, it is concluded that the wavenumber-frequency spectrum method is useful to analyze flow induced noise such as vehicle interior noise.
Full Paper
The effect of flow on the natural frequencies of a flexible plate
Peters, Herwig (1), Chen, Li (2), Kessissoglou, Nicole (1)
(1) UNSW Australia, Australia
(2) DSTO, Australia
ABSTRACT
Vorticity induced vibrations (VIV) are caused by alternating vortices downstream of a structure, which result in a lift force acting on the structure perpendicular to the direction of the mean flow. This oscillating lift force excites vibrations of the flexible structure. When the vortex shedding frequency coincides with a natural frequency of the system, the structure vibrates at large transverse displacement amplitudes. These resonances occur at the natural frequencies of the overall system and are usually very different from the natural frequencies of the structure in vacuo or in a static fluid, which makes the prediction of the VIV resonances difficult. In this work, harmonic and transient simulations are used to predict the natural frequencies of a flexible plate in vacuo, in a static fluid, and in fluid flow. The results illustrate the effect of stationary and flowing water on the natural frequencies of a steel plate.
Full Paper
The flow-induced noise of square finite wall-mounted cylinders in different boundary layers.
Porteous, Ric (1), Moreau, Danielle (1), Doolan, Con J (1), Prime, Zebb (1)
(1) University of Adelaide, Australia
ABSTRACT
The noise generated by a finite wall-mounted cylinder (FWMC) in cross-flow is relevant to a range of applications including aircraft landing gear, heat exchangers and automobile appendages. The noise generation characteristics and mechanisms of these objects depend primarily on the aspect ratio (ratio of length to width, L/W) and the height of the incoming boundary layer, δ . This paper presents acoustic and wake measurements for six square FWMC's in two different turbulent boundary layers. The aspect ratio of the cylinders ranged from 1.94 < L/W < 13.75 and the boundary layer heights were δ /W = 1.2 and 2.4. The periodic wake and far-field acoustic characteristics of the cylinders were measured simultaneously using hotwire anemometry and a single microphone. The results show that increasing the boundary layer height increases the overall noise for L/W ≤ 8.8 but reduces the overall noise level for L/W > 8.8.
Full Paper
New Zealand Code of Practice for retail fireworks - Revision of the noise testing provisions: Experiences and findings
Page, Wyatt H (1), McLaren, Stuart J (1)
(1) Massey University, New Zealand
ABSTRACT
Retail fireworks are sold in New Zealand (NZ) each year for a limited time after testing and approval by a qualified test certifier. In 2013, there were reports that some fireworks were excessively loud. Retail fireworks are regulated under the Hazardous Substances (Fireworks) Regulations 2001 which sets a level of 90 dB for fireworks with a percussive effect. However, as qualified test certifiers are generally not trained in noise measurement and may not understand many of the fundamental difficulties in making accurate noise measurements, they may be incorrectly measuring firework noise. This highlights the need to educate both test certifiers and importers about noise measurement. The NZ Environmental Protection Authority's Approved Code of Practice (COP) sets out requirements for the design, performance and testing of retail fireworks. This paper covers the process of revising the noise testing provisions of the COP, the public consultation process and the development of a new robust testing procedure. Using the new procedure, experimental findings unexpectedly demonstrated that wind effects and frequency-weighting selection have only a small effect on the measured noise levels of the percussive fireworks.
Full Paper
Discussion on noise control at workplaces
Pääkkönen, Rauno (1), Saine, Kari (2), Seppänen, Saara (3), Ollilla, Tapani (1)
(1) Finnish Institute of Occupational Health, Finland
(2) Finnish Institute of OcWärtsilä Finland Oy, Finlandcupational Health, Finland
(3) Tampere University of Technology, Finland
ABSTRACT
In Finland noise exposure and hearing losses remain about the same level although it is said that the work is changing rapidly towards office work. The persons at productive workplaces say often that it is not possible any more reduce noise exposure. Have the workplaces have done all that is possible especially concerning technical noise control possibilities? The measurement technology has improved significantly over the last 20 years. Also, construction technology and structures have improved. Is the productivity, efficiency and machine technology more important than human health? Many organizations state that well-being at work is very important in improving productivity and result of the company. Then it is also said that workers do not care. What are the real possibilities in improving the safety culture and noise control at workplaces? Are we prisoners of prejudices, is it impossible to use modern technology to reduce noise at workplaces.
Full Paper
Comparative study of the performance of smartphone-based sound level meter apps, with and without the application of a 1⁄2\" IEC-61094-4 working standard microphone, to IEC-61672 standard metering equipment in the detection of various problematic workplace noise environments
Robinson, David Paul (1), Tingay, James (1)
(1) Cirrus Research plc, UK
ABSTRACT
An increasing prevalence of sound level meter apps may appear to be a concern to manufacturers of metering equipment but such systems are readily disregarded by professionals due to unacceptable inaccuracy, incorrect measurement methods or parameters. On a technical basis, the [typically MEMS] microphone specifications are the primary limitation to the capabilities of such devices in meeting the requirements. This considered, the attachment of a high-quality condenser microphone and pre-amplifier, as used on professional equipment, may appear to be a solution for low-cost metering that meets IEC-61672, but it is shown that many other equipment factors affect the performance of the system, and conformance to the specifications. This study investigates the premise that, while it may be argued that approximate readings, provided by smartphone metering, can at least offer an indication that further investigation may be necessary, there exists the real chance that the shortfalls in equipment properly measuring the full range of required acoustical parameters will lead to non-detection of significant workplace or environmental noise problems.
Full Paper
Protection of workers from risks caused by loud sound fields. Comparison between the European and the United States standards.
Sabato, Alessandro (1), Sabato, Adolfo (1), Reda, Alfredo (2)
(1) Laboratorio di Tecnica del Controllo Ambientale, Italy
(2) Self-employed engineer, Italy
ABSTRACT
Workers protection from risk arising from prolonged exposure to loud acoustic fields plays a key role in the safeguard of people physical and mental wellbeing. In workplaces, depending on level and time of exposition, annoyance or permanent damage may occur. Furthermore, other parameters such as impulsive events, spectral composition, and phenomenon variability can influence the hazard connected to the sound and can, eventually, reduce protection. Among the most evolved systems used to ensure workers protection from noise, there are the European and the United States Standards. In Europe, safeguard is ensured through Directive 2003/10/EC of the European Parliament and of the Council of February 6th, 2003. It supplies the minimum health requirements to assure health-care and protection from loud sounds to those workers who are exposed to noise as a result of their work. In the United States, the OSHA Standard number 1910, subpart G "Occupational Safety and Environmental Control" regulates the procedures. In this work, noise produced in different work activities is measured using dosimeters and real-time analyzers. The results are then analyzed using the two different Directives to show whether they supply different protection levels and to highlight possible weaknesses in the individuation of protection from loud sounds.
Full Paper
A practical comparison of occupational noise standards
Tingay, James (1), Robinson, David Paul (1)
(1) Cirrus Research plc, UK
ABSTRACT
The use of digital signal processing in noise measurement instruments has dramatically increased the measurement capabilities of even the simplest sound level meters and noise dosimeters. There are often a wide range of frequency and time weightings available as well as a selection of thresholds, exchange rates, criterion times and criterion levels. In many modern instruments, the results of a measurement are presented to the user automatically and this can often result in confusion as to the correct value or parameter to report, especially when the metrics appear to be very similar. In the case of occupational noise exposure, this can result in the under or over reporting of values when there is a need to provide data under a range of different or multiple standards. This paper describes a review and a comparison of a range of different occupational noise standards using real-world noise sources. The review demonstrates the differences in how the same physical noise exposure is reported under these different regulations, how often similar standards can produce significantly different outcomes and suggests ways in which users can be informed about the nature of the noise measurement data that they are presented with.
Full Paper
Field noise measurement in the huge industrial plants for accurate prediction
Hida, Takahiro
JGC Corporation, Japan
ABSTRACT
Proper noise controls of the industrial plants based on accurate noise prediction are important since noise from these plants will affect wide area both inside and outside of the plants. Also, occupational noise exposure is serious problem for workers of the plants. However, it is not easy to predict the noise propagation from the industrial plants such as refineries, petrochemical and gas treatment plants because of their huge amount of noise sources and complicated structures as obstacles and reflectors. At the inter-noise conferences in the last two years, we have presented our field data of noise propagation from industrial plants over the desert and sea with prediction results followed by ISO method. In this paper we focus on sound propagation in the near filed of the industrial plants. From our new field measurements, the effect of the noise sources, obstacles, and various field circumstances is discussed. We also try to improve the usage of the ISO calculation methods for each plant condition at design phase based on our measurement experience.
Full Paper
Determining the transmission loss of apertures above the plane wave cutoff frequency
Li, Jiazhu (1), Chen, Jian (1), Li, Can (2)
(1) Institute of Sound and Vibration Research, Hefei University of Technology, China
(2) China Automotive Technology & Research Center, China
ABSTRACT
In order for enclosures and barriers to be effective, the sound transmission through holes and openings must be minimized. In this paper, a modal and sound transmission coefficient superposition (MSTCS) method is used to predict the sound transmission loss (TL) of apertures. The approach is applicable both below and above the cutoff frequency and may be used for apertures of arbitrary cross-section. Rectangular cross-section openings are considered and results are compared with the transfer matrix method, Sgard et al., acoustic FEM, and published experimental data and demonstrate good agreement with each other.
Full Paper
Ground effect due to periodic and resonant roughness structures
Shin, Ho-Chul (1), Taherzadeh, Shahram (1), Attenborough, Keith (1)
(1) Open University, UK
ABSTRACT
The recent expansion of cities throughout the world means that traffic noise is an increasing problem. The area of land between the traffic source and the receivers can provide an appropriate space where a series of low-rise roughness structures can be placed as an alternative to conventional noise barriers and earth berms. Through laboratory measurements, we have investigated the effect of periodic roughness elements on the sound propagation above a smooth hard surface. First, the periodicity-induced diffraction created by an array of solid roughness structures was studied both numerically and experimentally in the laboratory. The effects of hollow resonant elements with slit openings have been investigated also to add an additional destructive interference below the first roughness-induced destructive interference and thereby mitigate the adverse effect of the low-frequency surface waves generated by the presence of roughness elements. Finally, we have constructed and tested a nested configuration of slotted hollow roughness elements and measured the effects of the associated multiple resonance phenomenon.
Full Paper
Acoustic Yagi-Uda Antenna Using Resonance Tubes
Tamura, Yuki (1), Yatabe, Kohei (1), Ouchi, Yasuhiro (1), Oikawa, Yasuhiro (1), Yamasaki, Yoshio (1)
(1) Waseda University, Japan
ABSTRACT
A Yagi-Uda antenna gets high directivity by applying current phase shift between elements due to resonance phenomena. It has some directors and reflectors, which are elements without electric supply. The length of directors is shorter than half-wave and that of reflectors is longer than half-wave. We proposed an acoustic Yagi-Uda antenna which elements are resonance tubes and a loudspeaker. The aim of this research is to im- prove directivity in a specific frequency. This can be applied to Radio Acoustic Sounding System (RASS), which is a kind of radar for weather observation, or to a parametric loudspeaker. The phase shift of sound waves was observed in the condition with a resonance tube and without the tube at the same position. That shift changes suddenly around the resonance frequency of the tube. Our acoustic antenna has resonance tubes that have different length as directors and reflectors to apply this phenomenon. Moreover, the distances be- tween a loudspeaker and tubes were concerned by some experiments and by numerical analysis. The acoustic antenna showed directivity in an appropriate condition of the distances and the frequency of the sound source. It will be also added the consideration about the effective frequency band of this acoustic antenna.
Full Paper
Determination of noise damping by forests
Trimpop, Mattias (1), Mann, Peter (2)
(1) IfL GmbH, Germany
(2) BImA, Germany
ABSTRACT
To predict the attenuation value caused by a forest stand a model has been developed. The model depends on an attenuation coefficient for the forest and on the geometry of the forest and the positions for the source and the receiver. The attenuation coefficient has been measured by a specific test setup for several forest stands (three different pine forests and one oak forest stand) The stock of one pine stand was reduced in several steps and measured after each reduction. The results of the measurements lead not only to qualitative statements but also to quantitative attenuation values (and coefficients) for the different forest stands. The results also showed that the actual used model had to be extended because the sound path over the canopy can have a limiting effect on the maximum forest attenuation. This effect depends on the geometry of the forest and the sound and receiver positions as well as the specific forest attenuation coefficient. The extended model provides the possibility to predict the forest attenuation by forestal and geometric parameters.
Full Paper
Impulsive Response Analysis
Using Transient Energy Distribution Analysis
Chida, Shohei (1), Nakamura, Hiroki (2), Yamazaki, Toru (2)
(1) Graduate School of Kanagawa University, Japan
(2) Department of Mechanical Engineering, Kanagawa University, Japan
ABSTRACT
Statistical Energy Analysis (SEA) and Energy Distribution Analysis (EDA) are suitable for predicting responses to stationary vibrations. These methods consider a structure of interest as an assembly of subsystems and analyze energy flows between the subsystems. In particular, EDA can analyze vibrations over the whole frequency range, while SEA is basically used only for high frequencies. However, these methods do not consider transient dynamic characteristics, so they are not applicable to the analysis of unsteady vibrations such as impulsive vibrations. This paper proposes transient EDA (TEDA) as is extension of EDA to impulsive responses. The proposed method is expected to be a suitable tool for impulsive analysis of huge structures like ships. The feasibility of the proposed method is examined through an experiment with a test structure composed of three flat steel plates. Also, the proposed method is compared with TSEA. We find that TEDA can predict the vibration energy of each subsystem more accurately than TSEA. Measurements of the energy response of a structure composed of three flat steel plates, including a coupling at right angles, showed specific energy transfer characteristics: the maximum energy of the end plate that is far from the input plate was larger than that of the second plate that is between the input and the end plates; and energy peak rise time of the end plate was faster than that of the second plate.
Full Paper
Vibration transfer analysis based on characterization of vibration energy dissipation
Kitahara, Atsushi (1), Yoshimura, Takuya (1)
(1) Tokyo Metropolitan University, Japan
ABSTRACT
Reducing vibration energy of mechanical structures by controlling energy dissipation is important for improving structure-borne noise, such as interior noise in a vehicle. In this study, vibration transfer characteristics are investigated using vibration energy evaluation, when no particular vibration mode is dominant. A beam structure modeled by Finite Element approach is used as an example. We examine the efficient method of determining effective position to add damping. The method using distribution of dissipation power and that using damping addition sensitivity analysis of the vibration energy are examined. In the resonance excitation case, the optimum damping layout for vibration suppression can be determined by both methods. On the other hand, in the non-resonance excitation case, no obvious correlation is found between the optimum damping layout and the distribution of dissipation power. However, the analysis of damping addition sensitivity leads the optimum damping layout even if the excitation frequency is non-resonance.
Full Paper
Vibration analysis of a steam turbine blade
Mohan, R S (1), Sarkar, A (1), Sekhar, A Seshadri (1)
(1) IIT Madras, India
ABSTRACT
Blade failure is a common problem of a steam turbine and it's failure in-service results in safety risks, repair cost and non operational revenue losses. Thus, the reliability of these blades is very important for the successful operation of a steam turbine. Dynamic analysis of a steam turbine blade in computational environment is carried out in the present work. In order to gain physical insight into the flexural dynamics of such turbine blades with the inclusion of the rotor dynamic effect, the turbine blade was approximated as a twisted cantilever beam with an asymmetric aerofoil cross-section fixed on a rigid rotor disk. Methods to validate the computational procedures for cantilever beam were established. Similar computational procedures were leveraged for the turbine blade. Critical speeds were obtained for different excitations.
Full Paper
Improvement of Experimental SEA model accuracy using Independent Component Analysis
Nakamura, Hiroki (1), Chida, Shohei (1), Yamazaki, Toru (1)
(1) Kanagawa University, Japan
ABSTRACT
Statistical Energy Analysis (SEA) is a suitable tool to predict vibration stationary responses. It is roughly categorized into analytical, FEM based, and experimental SEA due to the process of model construction. SEA is expected to be used for designing machines with optimal vibration transfer paths. However experimental SEA model accuracy especially in low frequency is highly dependent on experimental condition and target structure. It is required to develop model construction process for more convenient use of SEA. In this paper, preprocessing algorithm using independent component analysis (ICA) is proposed for improvement of model construction of SEA. Here, ICA is a signal processing method which is originally developed for bio-signal analysis and it is used for separation of complex mixture of several vibration sources. Feasibility of the proposed method is examined through an experiment with a test structure, composed of three flat steel plates.
Full Paper
The modeling and free vibration analysis of coupled plates of various types
Shi, Shuangxia (1), Jin, Guoyong (1), Chen, Mingfei (1)
(1) Harbin Engineering University, China
ABSTRACT
This paper is concerned with the modeling and free vibration analysis of coupled plates of various types, which includes T-shape plates, cross shape plates and a panel-linked double-panel structure. The in-plane vibration and bending vibration probe are considered in coupled structures. The vibration problems are solved using an improved Fourier series method in which the in-plane displacement and bending displacement are expressed as the superposition of a double Fourier cosine series and several supplementary functions to ensure (improve) the uniform convergence (rate) of the Fourier series expansion. The dynamic responses of the coupled structural-acoustic system are obtained using the Rayleigh-Ritz procedure based on the energy expressions for the coupled system. The accuracy and effectiveness of the proposed method are validated through numerical examples and comparison with results obtained by the finite element analysis.
Full Paper
Numerical noise generation in modelled bearing vibration signals
Singh, Sarabjeet (1), Howard, Carl (1), Hansen, Colin (1), Kopke, Uwe (2)
(1) University of Adelaide, Australia
(2) Trackside Intelligence Pty Ltd, Australia
ABSTRACT
A two-dimensional (2-D) explicit dynamics finite element (FE) model of a rolling element bearing was solved using a commercial FE software package, LS-DYNA. It was found that the modelled bearing vibration signals contain a significant amount of numerical noise. This paper provides an explanation of the physical mech- anism by which the numerical noise is generated. The noise frequencies were analytically estimated and filtered out to achieve comparatively clean vibration signals and rolling element-to-raceway contact forces.
Full Paper
Free vibrations of a box-type structure by plates with arbitrary boundary conditions
Zhang, Kaipeng (1), Zhang, Tao (1), Wu, Han (2), Shi, Dongyan (1)
(1) Harbin Engineering University, China
(2) AVIC International Trade and Economic Development Ltd, Xi\'an, China
ABSTRACT
In this paper, a modified Fourier solution is developed for the free vibrations of a box-type structure as four elastically coupled rectangular plates with arbitrary boundary conditions. The modified Fourier solution for the problem is obtained using improved Fourier series method, in which both three displacements of the rectangular plates are represented by a new form of trigonometric series functions with a drastically improved convergence as compared with the conventional Fourier series. It is shown that the general coupling and boundary conditions are accounted for using the artificial spring technique and can be easily obtained by assigning the springs with corresponding values. All the unknown series expansion coefficients are treated as the generalized coordinates and solved using the Rayleigh-Ritz technique. The efficiency, accuracy and reliability of the proposed approach are demonstrated by comparison with the Finite Element Method (FEM) results. In addition, the current approach offers an easy analysis operation for the entire model parameters and the change of any parameter from one case to another is as easy as changing structure parameters without need of making any change to the solution procedure, thus this will make a parametric study and further mechanism analysis easier compared to most existing procedures.
Full Paper
Standard, quiet and super quiet - the modelling of flow and the reduction of turbulences
Bradwell, Simon
ABSTRACT
The understanding of noise and efficiency characteristics of fan motor systems is important for all engineers developing air movement systems whether they are for stand-alone ventilation systems or for air movement solutions incorporated into broader systems.The volume of air flow and air velocity through static pressure resistances are the main and vital variables controlling system performance in air movement. However if these characteristics are not controlled, then turbulence causes losses and low system performance.The paper explores the noise characteristics of typical fan types. As the most common fan types, fluid flow characteristics of both axial fans and single inlet centrifugal backward curve fans without housing (plug fans) are detailed and design improvements discussed.
Installation characteristics for improved noise are explored and recommendations for system design improvements are given including performance improvements in condensers and air handling units.Conclusions for mechanical engineers working on building systems are shown and recommendations and design principles given.
Full Paper
Stall detection using near-field low frequency and pressure modulation in turbomachines
Corsini, Alessandro (1), Feudo, Sara (1), Tortora, Cecilia (1), Ullucci, Graziano (2)
(1) Sapienza University of Rome, Italy
(2) SED Soluzioni Srl, Italy
ABSTRACT
This work investigates on the use of unconventional sensors to measure the near field unsteady pressure on the casing of a fan in a view to detect rotating stall. Rotating stall is an aerodynamic issue with a frequency signature usually half the rotor frequency. In low speed turbomachines, such as industrial fan, this turns in very low frequencies, even lower than 10 Hz. The authors developed and set-up a measurement system able to acquire low frequency pressure signals using dynamic microphones. Traditional methods use piezoelectric sensors, e.g., pressure tranducers or microphones, respectively in the near and far-field, to detect instability from the signal patterns with broad frequency ranges. Recently electret microphones have been proposed, but with a cut-off frequency of 20 Hz as such not suitable for signal in infrasound region. The sensor used in this work, have a narrower frequency range than more advanced technologies. In this paper the authors developed a measurement chain based on dynamic microphone and pressure transducer in order to create a stall warning system. They tested the system on a low speed axial fan and they validated the work against state of the art acoustic control techniques. For this reason those devices represent candidate solutions for the detection of the patterns typical of rotating stall in turbomachines.
Full Paper
Fan duct noise elimination by the use of helicoidal resonators
Lapka, Wojciech
Poznan University of Technology, Poland
ABSTRACT
This work focuses on describing the fan duct noise elimination by the use of helicoidal resonators. It is the newly patented passive acoustic filter in duct - especially cylindrical. The narrowband noise attenuation could be obtained by properly designed helicoidal shape inside cylindrical duct. The helicoidal resonator gives the possibility to reduce the discrete tonal sounds in different ways, a single or multiple application. The possible band filtering could be used to attenuate discrete noise generated in the range of rotational speeds of fan. Also, this work consists the theoretical considerations supported by practical examples of reduction of fan duct noise by the use of helicoidal resonators.
Full Paper
Local improvement of flow and noise performances of axial-flow fans in a household refrigerator
Seong-hun, Kim (1), Seung, Heo (1), Cheolung, Cheong (1), Taehoon, Kim (2)
(1) Pusan University, South Korea
(2) LG, South Korea
ABSTRACT
In this paper, numerical and experimental investigations on an axial-flow fan with grooved/double-sectional blades are performed to improve its performance in terms of volume flow rate and noise at a local operating point. The target fan is used to cool a mechanical room of a household refrigerator. However, it is found that the target system has more resistance than that for which the fan is originally designed and the fan's operating point is not optimal. First, the performance of the target fan unit is measured from the fan performance tester. Then, the P-Q curve is predicted using the virtual fan performance tester based on the CFD techniques to solve the incompressible RANS equations. The surface acoustic power of the fan unit is also predicted using the broadband noise sources modeled from the CFD results. The predicted P-Q curve is compared to the measured data, through which the validity of the numerical techniques is confirmed. On the basis of the prediction results, new fan units with modified fan's housing structures are devised. Further predictions using these new fan units show that these fan units generate higher volume flow rate while keeping surface acoustic power levels lower than the existing fan system on the local operating point
Full Paper
Withdrawn6
Withdrawn6,
ABSTRACT
Withdrawn6
Vocal problems for teachers and school acoustics - a field study
Durup, Nick (1), Shield, Bridget (2), Dance, Stephen (2), Sullivan, Rory (3)
(1) London South Bank University, UK,Sharps Redmore Acoustic Consultants, United Kingdom
(2) London South Bank University, UK
(3) Sharps Redmore Acoustic Consultants, UK, Sharps Redmore Acoustic Consultants, United Kingdom
ABSTRACT
School acoustic design in the UK is traditionally concerned with the needs of the listener, rather than the voice ergonomics of the speaker. However, a recent survey undertaken by London South Bank University (LSBU) indicated that over 65% of the surveyed teachers had experienced voice problems during their career. This supports other studies suggesting that teachers have a significantly higher rate of voice problems than the general population. In an effort to better understand the influence of classroom acoustic design on the speech levels of teachers LSBU is currently undertaking measurements of teachers' voices in different classroom types. The measurements are being undertaken using an Ambulatory Phonation Monitor (APM) which measures voice parameters directly from the skin vibrations in the neck, thus eliminating the effects of other noise sources in the environment. The rooms involved are acoustically benchmarked separately to enable relationships between the voice data and acoustic parameters to be investigated.This paper presents results of the field measurements to date, with a brief summary of the data collected to date from the teachers' questionnaire survey, and discusses some of the initial findings.South Bank University (LSBU) indicated that over 65% of the surveyed teachers had experienced voice problems during their career. This supports other studies suggesting that teachers have a significantly higher rate of voice problems compared with the general population. In an effort to better understand the influence of classroom acoustic design on the speech levels of teachers LSBU is currently undertaking measurements of teachers' voices in different classroom types. The measurements are being undertaken using an Ambulatory Phonation Monitor (APM) which measures voice parameters directly from the skin vibrations in the neck, thus eliminating the effects of other noise sources in the environment. The rooms involved are acoustically benchmarked separately to enable to relationships between the voice data and acoustic parameters to be investigated. This paper will present results of the teachers' survey and the field measurements to date, and discuss some of the initial findings.
Full Paper
Classrooms and voice recognition applications in a foreign language teaching
Ono, Yuichi (1), Ishihara, Manabu (2), Onishi, Akio (3), Yamashiro, Mitsuo (4)
(1) University of Tsukuba, Japan
(2) Oyama National College of Technology, Japan
(3) Version2, Japan
(4) Ashikaga Institute of Technology, Japan
ABSTRACT
The advantages of using Voice recognition software in a foreign language course to enhance speaking accuracy and fluency have been suggested in the literature (1,2). One of the difficulties faced with Voice recognition software is a "noise" around the speakers. In our campus, the normal class size is around 40 for one English course. This means is that the software has to recognize speaker's voice correctly among other speakers' "noise". In this study, we carried out several experiments in terms of the system and the devices of the classroom. We picked up two kinds of classroom. One is Computer-Assisted Language Learning (CALL) room, a specialized classroom for foreign language learning, where there are wired individual PC and headphone with microphone for each student. The other classroom is a normal classroom, where tablet computers or mobile devices were utilized. Our expectation is that the rate of recognition should be better in CALL classrooms than that of normal classroom with tablet computers, since students use headphones and microphones in a CALL classroom. The results of our study indicated that this hypothesis was true only with sight significance. This paper suggests that it is still difficult to integrate Voice recognition software into normal classroom with local application with tablet PC.
Full Paper
Acoustic design guidelines for dementia care facilities
Hayne, Michael James (1), Fleming, Richard (2)
(1) Floth Sustainable Building Consultants, Australia
(2) University of Wollongong, Australia
ABSTRACT
People with dementia are particularly affected by the acoustic environment. While people with dementia might have normal hearing, they can lose the ability to interpret what they hear accurately. As such, the amount, type and variety of noise a person with dementia is exposed to needs to be carefully regulated, as over or under exposure to noise can cause confusion, illusions, frustration and agitation. This paper explores the role of noise on the ability of people with dementia to interpret and understand their surroundings. Examples are provided of acoustical design and management practices that contribute to increased levels of agitation and aggression among residents who have dementia. Guidelines are provided for the acoustic design of dementia care facilities with the ultimate aim of creating facilities that are calming and engaging for people with dementia in residential care.
Full Paper
A summary of the 2014 FGI and sound & vibration guidelines for healthcare facilities
Van Wyk, Kenric (1), Horan, Daniel (2), Murphy, Kristen (1)
(1) Acoustics By Design, USA
(2) Cavanaugh Tocci Associates, USA
ABSTRACT
The FGI Guidelines are the two-volume standard reference document for healthcare construction. Both volumes (hospitals; residential care) include comprehensive acoustical criteria written in code language that are used by authorities in the United States and 60 other countries, and serve as the sole reference for acoustics in USGBC-LEED for Health Care. The acoustical criteria set "minimum standards" and were developed by the FGI Acoustics Working Group, a ten-year-old standing committee including members of the Acoustical Society of America, INCE-USA, and other professional organizations. This group authors the sole acoustical reference for the Guidelines called Sound & Vibration Design Guidelines for Health Care Facilities (S&V-3.0-2014), publically available on the FGI website and to be published by Springer-Verlag during the first half of 2015. The Guidelines are edited and re-issued every four years by the Facility Guidelines Institute, and jointly published with the American Hospital Association. The Guidelines are revised following an open, formal, Continual Improvement Process that includes a peer- and public-review incorporating the latest research and changes in healthcare laws. This discussion by the national Secretary of the FGI Acoustics Working Group and the Chair of its Education Committee will: address the new code requirements related to acoustics; summarize the myriad changes from the 2010 edition; and describe the public and comment process for the next edition to be released in 2018.
Full Paper
Review of design approaches to acoustics in Australian hospitals
Zoontjens, Luke (1), Cockings, Thomas (1)
(1) SLR Consulting, Australia
ABSTRACT
Surveys of Australian hospital outpatients appear to overlook quietness, one of the lowest areas of satisfaction internationally and an issue which extends beyond individual dissatisfaction to impact actual health outcomes in both current (and soon to be commissioned) hospitals. However, in terms of acoustic design, few Australian hospitals are consistent in their tender requirements and construction provisions, with the exception of reference to several Australian Standards which are arguably due for an update. Consequently, recent research findings challenge the basis of existing guidelines and approaches currently recommended for the acoustical design of these and other healthcare facilities. This paper presents a short review of current guidelines in use and compares these guidelines against the literature state of the art. Recommendations are made as to suitable design positions to be used in the tendering and specification of future healthcare facilities.
Full Paper
Extensions of EN 12354 vibration reduction index expressions by means of FEM calculations
Crispin, Charlotte (1), De Geetere, Lieven (1), Ingelaere, Bart (1)
(1) Belgian Building Research Institute, Belgium
ABSTRACT
In this paper, a comparison is made between the measured and calculated vibration reduction indices (Kij ) and the engineering approximations in EN 12354-1. First, the existing expressions in EN 12354-1 for simple junctions of homogeneous elements are compared with a large data set of measured and calculated Kij spectra. For more complex junctions, not in EN 12354-1, like junctions with cavity walls (H-junctions) and junctions with different surface masses for in-line elements, a large number of FEM calculations have been made, from which new engineering approximations are derived.
Full Paper
Psychoacoustical evaluation of heavyweight floor impact sounds in apartment buildings
Jeon, Jin Yong (1), Oh, Seong Min (1)
(1) Hanyang University, South Korea
ABSTRACT
An auditory experiment was conducted to establish annoyance criteria for floor impact noise in apartment buildings. Heavyweight floor impact sounds were recorded using an impact ball; the impact sound pressure level (SPL) together with the temporal decay rate (DR), which is quantified by the dB drop per second, was analyzed. For the experiment, A-weighted exposure levels of the heavyweight floor impact sounds ranging 34-73 dB were evaluated at 3 dB intervals. Participants used a 7-point verbal scale to evaluate the level of annoyance from floor impact noise. The results show that the annoyance increases with increasing impact SPL and decreasing DR. Consequently, a classification and an acceptable level of floor impact sounds were proposed.
Full Paper
A new metric to quantify and evaluate low frequency impact noise
LoVerde, John J (1), Dong, Wayland (1)
(1) Veneklasen Associates, USA
ABSTRACT
Low frequency footfall noise ("thudding") is a common source of complaints in lightweight (timber) joist- framed multifamily projects. Previous work by the authors has indicated that the low frequency impact sound pressure levels (LFISPL) from a standard ISO tapping machine are highly correlated with occupant reaction. It remains to translate the raw LFISPL data into a useful single number metric that maintains the high correlation with subjective reaction, provides adequate dynamic range to distinguish the performance of different assemblies, and is conveniently scaled. This paper introduces Low-frequency Impact Rating or LIR, a new metric to quantify and evaluate low frequency impact noise.
Full Paper
Determination of vibration acceptability and annoyance design indicators for human response to wooden-floor vibrations
Negreira, Juan (1), Trollé, Arnaud (2), Jarnerö, Kirsi (3), Sjökvist, Lars-Göran (3), Bard, Delphine (1)
(1) Lund University, Sweden
(2) Université de Lyon, France
(3) Technical Research Institute of Sweden, Sweden
ABSTRACT
The vibrational response of wooden floor systems is an issue that needs to be dealt with more adequately. Notably, studies addressing human response to vibrations are needed in order to better estimate what level of vibrations in dwellings can be seen as acceptable. In this investigation, measurements on five different floors were performed in a laboratory environment at two locations in Sweden. Acceleration measurements were carried out while a person either was walking on a particular floor or was seated in a chair placed there, as the test leader was walking on the floor. These participants filled out a questionnaire regarding their perception and experiencing of the vibrations. Independently of the subjective tests, acceleration measurements were also carried out, using a shaker as excitation source, with the aim of determining the dynamic characteristics of the floors. In addition, static load tests were performed using displacement gauges so as to measure the floor deflections. The ultimate aim was to develop indicators of human response to floor vibrations, specifically those regarding vibration acceptability and vibration annoyance, their being drawn based on relationships between the questionnaire responses obtained and the parameter values determined on the basis of the measurements carried out.
Full Paper
Open plan offices - classification scheme based on ISO 3382-3 parameters
Nocke, Christian
Akustikbüro Oldenburg, Germany
ABSTRACT
With the introduction of ISO 3382, part 3 for open plan offices in 2012 new room acoustic parameters have been introduced. For these parameters only little experience in real life projects is available. In contrast to the draft version of IOS 3382-3 in 2009 the final 2012 version of ISO 3382-3 does not suggest a classification scheme on open plan offices. With the revision of German guideline VDI 2569 on "Sound insulation and room acoustic design in offices" a classification scheme based on the ISO 3382-3 parameters is discussed. The result is a classification into three quality levels for single and multi-person offices. The definitions on propagation paths (in ISO 3382-3) as well as other aspects of ISO 3382-3 will be discussed and additional recommendations and clarifications will be presented.
Full Paper
Indoor pass-by noise engineering: a motorbike application case
Bianciardi, Fabio (1), Janssens, Karl (1), Choukri, Mostapha (1), Van Der Auweraer, Herman (1)
(1) LMS International, Belgium
ABSTRACT
Pass-by noise testing is nowadays a well-defined procedure in the development process of motorbikes. Manufacturers facing issues of non-compliance with regulations are looking for techniques to quantify the subsystem noise contributions, enabling the validation of designs for pass-by noise targets, early in the design process. Masking techniques are nowadays often used to separate the noise source contributions. However, since these techniques are time consuming and also have an influence on the operating conditions, motorbike companies are seeking for faster solutions. In this study, a time-domain TPA method was investigated and tested on a Piaggio Beverly 350 in an indoor pass-by noise test. The method consists in the application of time-domain filters, derived from FRF measurements, to microphone measurements close to the noise generating components. The results are time histories of the acoustic loads and partial contributions to the array of target microphones on the two sides of the testing room. The synthesized target response signals are mixed together into an overall pass-by noise level by taking into account the speed profile of the motorbike. The TPA method helps engineers to quantify the noise contributions to the overall pass-by noise level, with a remarkable time saved compared to the masking approach.
Full Paper
Target setting and source contribution for sound quality of a motorcycle
Lu, Ming-Hung (1), Jen, Ming Une (1)
(1) Industrial Technology Research Institute, Taiwan
ABSTRACT
Sound quality is an essential competitive attribute for motorcycles' marketing. In this study, the sound perception of a motorcycle, powered by a 400 cc single-cylinder engine, didn't achieve its "sporty" statement and the associated sound quality refinement engineering was initiated. The first phase of refinement included benchmark, noise source contribution and target setting. This paper focuses on the methods in setting sound target through source contribution and sound synthesization. Noise data were measured in a hemi-anechoic chamber with a rolling road facility. Loudness, sharpness and order spectra were used to provide objective quantification metrics. From the results of subjective and objective evaluation, it was concluded that the motorcycle studied should increase its sound pressure level, loudness and sharpness; it also should magnify the lower integer-order components of the perceived sound and suppress the single-cylinder engine characteristic half-order components. The noise source contribution results validated the exhaust and intake systems should be improved first to fulfill a favorable sound quality. Combining the objective, subjective and source contribution results, this study successfully synthesized a promising and feasible vehicle level sound target. It was then cascaded to get the synthesized intake and exhaust noise targets for next CAE design modification.
Full Paper
Vehicle Chassis Decoupling Control Based on Neural Network Inverse Method
Yang, Jun (1), Zhao, Linfeng (1), Chen, Wuwei (1), Huang, He (1), Xia, Guang (1)
(1) Hefei University of Technology, Hefei China
ABSTRACT
In order to eliminate the interference and coupling among automobile chassis electronic control subsystems, an integrated decoupling control approach based on neural network inverse method was proposed. The integration of active front steering (AFS), direct yaw moment control (DYC) and active suspension (ASS) was studied. According to Inter-actor algorithm, the reversibility of chassis system was analyzed and a BP neural network inverse system of the multivariable chassis system was obtained. Designing a close-loop controller and combining it with neural network inverse system, a compound controller was completed to improve dynamic performance. The simulation results showed that the proposed decoupling control approach could eliminate the interference and couple among automobile chassis electronic control subsystems, and improve the automobile handling and stability performance.
Full Paper
The characteristic identification of disc brake squeal based on ensemble empirical mode decomposition
Yao, Liang (1), Hiroshi, Yamaura (1)
(1) Tokyo Institute of Technology, Japan
ABSTRACT
Disc brake squeal, which is considered as a self-excited vibration induced by friction force, has received much attention over decades due to the high customer requirements of the NVH properties of vehicles. This paper presents a characteristic identifying method for the disc brake squeal by analysing the acoustic brake squeal signal obtained from experiment. The sound of brake squeal was recorded with a sound level meter to obtain the acoustic signal that later is examined by implementing several different signal processing methods. Firstly, the Fast Fourier Transform and the Short-Time Fourier Transform are performed to illustrate the frequency components of the signal and their evolution with time. Later, the acoustic signal is analyzed using ensemble empirical mode decomposition (EEMD) which is improved from empirical mode decomposition (EMD) by adding white noises of finite amplitude to the original acoustic signal to alleviate mode mixing problem occurred in EMD. After the implementation of EEMD, the original signal is decomposed into several intrinsic mode functions (IMFs). Finally, the Hilbert Transform is conducted for revealing the detailed information about the frequency and amplitude features of each calculated IMF.
Full Paper
Instability prediction of brake squeal by nonlinear stability analysis
Zhang, Zhi (1), Oberst, Sebastian (1), Lai, Joseph C S (1)
(1) UNSW Canberra, Australia
ABSTRACT
Prediction of brake squeal as unwanted high frequency noise above 1 kHz remains a challenging problem despite substantial research efforts in the past two decades. Brake squeal, triggered by friction-induced self-excited vibration, can be caused by many different and interacting mechanisms with nonlinear origins in material properties and boundary conditions. Although brake squeal is essentially a nonlinear phenomenon, the standard industrial practice for prediction of brake squeal relies on the linear complex eigenvalue analysis which may under-predict or over-predict the number of unstable vibration modes. Brake squeal can be considered in nonlinear dynamics terms to be caused by a friction-induced self-excitation driven into instability and oscillating in a limit cycle through super-critical Andronov-Hopf bifurcations. In this paper, a nonlinear stability analysis that may be applied to a full brake system is examined using an unforced 4-DOF friction oscillator with cubic nonlinearity. The local bifurcation behaviour of this model is studied using the normal form theory and the nonlinear stability boundary is evaluated. Differences between results of linear and nonlinear analyses are discussed and the limitations of the linear analysis are highlighted. The energy provided by friction and consumed by damping is calculated by multiple scales method to provide a physical explanation for instability generation.
Full Paper
Modelling of Fluid-Structure Interactions in the Hydraulic Circuit of Passive Interconnected Suspensions
Zhao, Jing (1), Zhang, Nong (1), Ji, Jin Chen (1)
(1) University of Sydney, Australia
ABSTRACT
The pressure changes in the liquid-filled fluid circuits of Hydraulically Interconnected Suspensions (HIS) often lead to vibration of the whole pipeline and associated structures and hence become a source of structural noise, which degrades ride comfort.
This paper presents the numerical and experimental investigation into the vibration of this kind of hydraulic circuit. The one-dimensional wave theory is employed to formulate the equations of motions that govern the dynamics of the fluid-structural system. Axial and lateral vibrations as well as the effects of shear deformation on the lateral vibration of the pipe are considered. The dynamic interaction between fluid and pipe is modelled by considering Poisson and junction coupling.
The Transfer Matrix Method (TMM) is applied to determine the steady state response of the fluid-structural system, which consists of various pipe sections, hose sections, damper valves, accumulators, supports and joints.
Laboratory experiments are performed on a liquid-filled hydraulic circuit with pulse trigger. The measured steady-state responses of the fluid circuit are compared with those obtained from the numerical simulations of the developed hydraulic circuit model. It is found that the developed model of the hydraulic systems including the coupling with boundaries has a reasonable accuracy in the frequency range of interest.
Full Paper
Tyre tread pattern noise optimization by a coupled source-human perception model
Bekke, Dirk A (1), Wijnant, Ysbrand H (2), De Boer, Andre (2), Bezemer-Krijnen, Marieke (2)
(1) Apollo Tyres Global R&D, The Netherlands
(2) University of Twente, The Netherlands
ABSTRACT
The current tyre design process uses many experimental evaluations and it may take therefore more than 2 years to develop a tyre. The use of simulation tools improves and speeds up this process. Research has shown that the human perception of tyre tread pattern noise is mainly determined by the noise characteristics: level, tonalness and modulation (also called drumming). In this paper a new source model and human perception model is described. The source modelling approach predicts the correct trends of the three tyre tread pattern noise characteristics. From the noise characteristics dedicated Sound Quality Metrics are defined: for level the Standard Deviation (STD), for tonalness the Order Prominence (OP) and for modulation the Multi- Order Modulation (MOM). Using these Sound Quality Metrics the human perception model is obtained by regression analysis, predicting the human perception of tyre tread pattern noise correctly (R2=0.94). The coupled source - human perception model enables a very fast optimization of a complete tyre tread pattern design to human comfort.
Full Paper
An investigation of the relationship between texture and tyre/road noise for different types of road surfaces and passenger car tyres
Berge, Truls (1), Viggen, Erlend Magnus (1)
(1) SINTEF ICT, Norway
ABSTRACT
The texture of the road surface has a major influence on the generation of tyre/road noise. For dense surfaces this may be the most important factor besides the tyre characteristics themselves. Throughout several projects, SINTEF has performed measurements of the tyre/road noise of a wide range of passenger car tyres on different types of road surfaces. These road surfaces are both normally used road surfaces in Norway and road surfaces on test areas. In this paper, some results from the analysis of the relationship between the texture levels and the tyre/road noise levels are presented. In previous investigations it has been found that there is a positive correlation between texture levels at longer wavelengths (like 20-200 mm) and the noise levels, while there is a negative correlation between texture levels at shorter wavelengths (below 8 mm) and the noise levels. In our analysis, the former is confirmed and the latter is found true for some data sets, but not for others. The analysis also shows that the noise from different tyres has a similar relationship with texture, even if the overall noise levels differ.
Full Paper
A study of the tyre cavity resonance and its mitigation using modal analysis method
Chanpong, Napasin (1), Mohamed, Zamri (1), Wei, Haiqiao (2), Watkins, Simon (1), Wang, Xu (1)
(1) RMIT University, Australia
(2) Tianjin University, China
ABSTRACT
This paper will focus on determining characteristics of tyre cavity resonance noise and its mitigation method. There are many factors that affect the noise transmitted to vehicle cabin, this includes coupling mode of structure and tyre air cavity which will be investigated in this paper. The results from experimental modal analysis will be compared with those from finite element modal analysis. These investigations would lead to understanding and reduction of tyre cavity resonance noise. Tyre samples were tested for their material properties using tensile tests and wheel assembly was tested for its dynamic properties through roving impact hammer tests. The frequency response data of roving impact hammer tests on a wheel tyre assembly was processed using MEScope software for identifying its mode shape. The results have shown the significant vibration response amplitude peak between 200-250 Hz is related to the tyre cavity resonance noise.
Full Paper
Characterisation of low-noise tyres for the roads of Hong Kong
Hung, Wing-tat (1), Leung, Randolph Chi-kin (2), Lam, Yat Ken (2)
(1) CEE, HKPolyU, Hong Kong
(2) Hong Kong Polytechnic University, Hong Kong
ABSTRACT
This study on low noise tyres started with a survey on commonly used tyres on 941 light duty vehicles. Subsequently, most common brands of tyre with a carefully selected size and tread block patterns were selected for testing on one commonly laid road surface, namely wearing course (WC), and one low noise road surface, namely polymer modified friction course (PMFC). Over 30 new and old tyres with varying properties of rubber hardness, depth and sizes were tested; tyre/road noise, air and road surface temperature, tyre pressure and vibration data were recorded. In order to identify the tyre properties on tyre/road noise, over 500 runs on the roads were made. It was found that the bi-directional & asynchronous (Michelin) was the quietest and the symmetrical tyre pattern (SRTT) was the noisiest on WC. The asymmetric pattern (Yokohama C.drive) became noisiest on PMFC. The change of driving speed from 50 to 70 km/h changed the noise order of bi-directional tyre (Yokohama A.drive) and the directional tyre (Dunlop Direzza). Tyre/road noise increased as the tyre rubber hardness increased owing to aging. The effects of the tyre tread depth and the tyre size on the level of noise are uncertain and minor.
Full Paper
Temperature influence on tyre/road noise of selected tyres
Mioduszewski, Piotr (1), Taryma, Stanisław (1), Woźniak, Ryszard (1)
(1) Gdansk University of Technology, Poland
ABSTRACT
Air and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation.
Tyre/road noise measurements using CPX method were performed to establish correlation between noise emission and ambient temperature for a set of ten selected tyres (characterized by a wide range of noise levels and including the two ISO reference tyres) on a SMA8 dense pavement within the recommended air temperature range from 5oC to 30oC with a step of about 5oC. Both air and road temperatures were taken into consideration. The results of this experiment were presented and discussed in the paper. A good correlation between air and road surface temperature was outlined. A linear relationship between noise emission and temperature was observed for eight tested tyres. The derived temperature correction factor was varied from -0.067 dB/oC to -0.145 dB/oC with an average of -0.107 dB/oC (-0.09 dB/oC for the two ISO reference tyres). There was no correlation for the remaining two tested tyres.
Full Paper
Influence of Circumferential Tread Pattern Stiffness on Tire Road Noise Generation under Driving Torque
Stalter, Frank (1), Gauterin, Frank (1)
(1) Karlsruhe Institute of Technology KIT, Germany
ABSTRACT
Concerning the sound emission of electric vehicles there are two main challenges: On the one hand, the exterior noise is on a very low noise level and approaching electric vehicles might not be recognized in city traffic. On the other hand, compared to internal combustion engines, electric drives develop a considerably high torque from the standstill which might increases tire road noise of about 10 dB in the near-field. Since combustion engine noise gets eliminated, tire road noise will not be masked anymore during acceleration but instead occurs as a disturbing, dominant acoustic source.
The paper describes first an inner drum test rig which allows the reproducible measurement of tire road noise on real road surfaces at driving and braking torque. Then, test results of special tires with different rubber compounds and pattern designs are presented. The influence of pattern stiffness and tire torque on tire road noise generation is analysed. Additional the inner drum test results were validated by pass-by measurements on different road surfaces. Finally, the effects and mechanisms of the noise phenomena are discussed and tire pattern design concepts for low noise emission under driving torque are derived.
Full Paper
A Simulation Methodology for Tire/Road Vibration Noise analysis
Yintao, Wei (1), Feng, Xijing (1), Xiang, Dabing (1), Chen, Yalong (1)
(1) Tsinghua University, China
ABSTRACT
A new methodology for simulating tire/road vibration noise is presented in this paper, which is is based on the Mixed Lagrange-Euler Method and Pseudo Excitation Method(PEM). A non- rotational acceleration field is constructed by mapping the acceleration of the Lagrange mesh onto the Euler mesh. Using this acceleration field as the acoustic source, the rolling noise can be predicted numerically using the Boundary Element Method (BEM) and Finite Element Method (FEM). In addition, a Pseudo Excitation Method(PEM) is proposed to simulate effect of road surface profile on the tire noise., which transfers the road elevation power spectral density(PSD) to the sum of harmonic excitation. A frequency domain analysis can be conducted to obtain the dynamical response of the tire on the real road and a sound emission analysis can be performed to get the sound field excited by road profile. In this way the tire/road vibration noise can be modeled completely.
Full Paper
Study on the effect of alignment style on shafting-shell coupled system radiated noise caused by propeller force
Cao, Yipeng (1), Zhang, Runze (1), Yang, Guodong (1)
(1) Harbin Engineering University, China
ABSTRACT
For the underwater structure, the propeller excitation force play an important role which can induce structure vibration and radiated noise in low frequency. Because of the arrangement of shafting, it is difficult to control the vibration of shafting-shell system. The effect of shafting alignment style on shafting-shell coupled system radiated noise is studied in this paper. The 2D Reynolds equation is calculated by finite difference method. The fluid film pressure distribution of each bearing is calculated. Load increment method is used to calculate the fluid film stiffness and finite element method is adopted to calculate the bearing support stiffness. On the basis of stiffness value, the propeller, shafting and shell coupled system is built by finite element method. The characteristic of shell underwater radiated noise caused by propeller force is studied. The alignment style of shafting is changed. The effect of alignment style on shafting-shell coupled system radiated pressure is calculated.
Full Paper
Underwater noise generated by merchants ships in coastal waters of the Gulf of Gdansk
Listewnik, Karol
Polish Naval Academy, Poland
ABSTRACT
Currently, there has been a growing interest in monitoring underwater sound as pollution on the environment. The aim of the study was to gather experience in the measurement of commercial vessels and information about the changes in frequency and sound level for typical commercial vessels during normal operation at the selected point of shipping line. The paper presents description and chosen results of measurements campaign of underwater noise generated by commercial vessels during normal operating conditions. Measurement campaign was carried out in several multi-day cycles in a designated place on the shipping line at a depth of 20 m. The underwater noise measurements were recorded with regard to the current parameters of the ship: draught at the bow and stern, speed and route transition (by AIS) and environmental conditions: sea bathymetry, wind, sea state, sound speed profiles with temperature, density and depth.
Full Paper
Modelling underwater shipping noise in the Great Barrier Reef Marine Park using AIS vessel track data
MacGillivray, Alexander (1), McPherson, Craig (2), McPherson, Geoff (3), Izett, Jonathan (1), Gosselin, Jeremy (1), Li, Zizheng (1), Hannay, David (1)
(1) JASCO Ltd., Canada
(2) JASCO Pty Ltd., Australia
(3) James Cook University, Australia
ABSTRACT
Shipping traffic is the largest contributor of anthropogenic noise in the ocean. Chronic exposure to shipping noise may be a significant habitat-level stressor to marine fauna. While sound measurements can characterise shipping noise at discrete locations and depths, acoustic models can predict anthropogenic sound levels over large regions of the ocean provided the types and locations of all important sound sources are known. We have developed one such model that uses Automated Identification System (AIS) ship tracking data and wind speed data to simulate the time-dependent noise field originating from many ships inside a large number of ships over a wide geographic area. We apply this model to simulate noise from ship traffic in a 25,000 km2 region of the Great Barrier Reef Marine Park, off the coast of Townsville, Qld, using three months of AIS data. Acoustic source levels are assigned to the vessels present based on the respective ship-class information embedded in the AIS records. Frequency-dependent propagation loss functions in four dimensions (three spatial and time) are pre-computed for several zones within the study area, based on local bathymetry, geoacoustic, and water column properties. Modelled shipping noise predictions are compared with acoustic measurements collected at Wheeler Reef, off Townsville from April-July 2013.
Full Paper
Real variability in ship systems' noise and vibration. Design and through-life management implications for underwater noise and habitability
McIntosh, David James
QinetiQ, UK
ABSTRACT
Customers require completed ships to achieve acoustic performance relating to military stealth, standards for crew and passenger habitability and legislation for environmental protection. Design activity derives equipment and system specifications for machines, distributed systems and isolation treatments, since the whole ship performance achievability and sustainability relates directly to component noises and vibrations. The paper examines databases, compiled over many years, during noise rangings and supporting vibration surveys, for several ship classes. The databases allow for objective study of the statistical variability evident in a sample of typical machinery source mechanisms that relate to specific measures of performance. The evidence provides important findings. Critically, very significant variability exists in real underwater noise performance and the related vibrations when compared to median measurements and fixed targets. Technical and cost implications of this observation should be considered by initial ship designs or update programmes, where multiple systems and related mechanisms co-exist. Authorities planning condition based maintenance for system availability and the through-life management of onboard habitability or underwater noise are also encouraged to study the predicted or evidential behaviours using such an approach. Stakeholders in different disciplines should expect mutual benefits. Surveying is recommended, typically using available populations of systems on ships in-service.
Full Paper
Is underwater thermal noise useful?
Readhead, Mark L
DSTO, Australia
ABSTRACT
Traditionally thermal noise has been considered an inconvenient nuisance in underwater acoustic sound pressure measurements. Theory (e.g. Mellen, 1952) shows that the noise spectrum increases with frequency, and provides a lower limit for measurements above 50 kHz. However, Weaver and Lobkis (2001, 2003) showed that by using an ultrasonic detector to correlate thermal fluctuations in a metal block, they could extract details of the block's dimensions, in much the same way as if they had used the detector for active transmission and reception. This paper will examine the theory and previous measurements, and provide further measurements of thermal noise.
Full Paper
Attenuation of low frequency underwater noise using arrays of air-filled resonators
Wochner, Mark S (1), Lee, Kevin M (2), McNeese, Andrew R (2), Wilson, Preston S (2)
(1) AdBm Technologies, USA
(2) University of Texas at Austin, USA
ABSTRACT
This paper investigates the acoustic behavior of underwater air-filled resonators that could potentially be used in an underwater noise abatement system. The resonators are similar to Helmholtz resonators without a neck, consisting of underwater inverted air-filled cavities with combinations of rigid and elastic wall members, and they are intended to be fastened to a framework forming a stationary array surrounding a noise source, such as a pile driving operation, a natural resource production platform, or an air gun array. Previous work has demonstrated the potential of surrounding noise sources with arrays of large stationary encapsulated bubbles that can be designed to attenuate sound levels over any desired frequency band and with levels of reduction up to 50 dB [Lee and Wilson, Proceedings of Meeting on Acoustics 19, 075048 (2013)]. Open water measurements of underwater sound attenuation using resonators were obtained during a set of lake experiments, where a low-frequency electromechanical sound source was surrounded by different arrays of resonators. The results indicate that air-filled resonators are a potential alternative to using encapsulated bubbles for low frequency underwater noise mitigation.
Full Paper
On the Study of Effects of Views to Water Space on Noise Annoyance Perceptions at Homes
Leung, T M (1), Chau, C K (1), Tang, Shiu Keung (1), Pun, L S C (1)
(1) Hong Kong Polytechnic University, Hong Kong
ABSTRACT
Noise annoyance poses various adverse effects on health and well-being of human beings. Earlier studies have shown that greenery views perceived from the apartments can reduce traffic-induced noise annoyances as a result of audio-visual effects. This study intended to explore whether similar noise annoyance moderation effects could be provided by perception of water spaces. Specifically, this study aimed to explore and quantify the effects of different types of water views on noise annoyance. The relationship between restorative capacity of water and noise annoyance was also revealed. Three residential estates in Hong Kong with views to rivers and seas respectively were selected for this study. One thousand four hundred and forty-six respondents were successfully administered via a series of questionnaire surveys, and the noise levels at homes were predicted using CRTN method. Results were analyzed to formulate multivariate ordered logit models linking noise annoyance, views to different types of water spaces and personal characteristics of the respondents. Findings from the study can facilitate urban planners and building designers in planning water spaces near residential estates so as to reduce noise annoyance. Other than the findings arising from this study, the methodology formulated in this study can be applied to study the effect of perception of other types of water spaces.
Full Paper
WithdrawnA
WithdrawnA,
ABSTRACT
WithdrawnA
How the meaning a person gives to tranquility could affect the appraisal of the urban park soundscape
Botteldooren, Dick (1), Filipan, Karlo (1), Boes, Michiel (1), De Coensel, Bert (1)
(1) Ghent University, Belgium
ABSTRACT
It has previously been established that different people attach a different meaning to the concept of "tranquil public space". A majority of persons associate tranquility with social interaction, but others associate tranquility with hearing sounds from nature or even with pure silence. Having these different beliefs and views in mind, hypotheses could be formulated on their effect on the perception and appraisal of soundscapes in urban parks. Firstly, persons associating tranquility with sounds from nature may focus more on hearing these sounds while visiting a park, and might notice them more often as a consequence. Secondly, the meaning given to tranquility also influences one's frame of reference and expectations. Thus, persons associating silence or sounds from nature to tranquility might state more easily that they hear less natural sounds and more mechanical sounds when visiting a park. These hypotheses were tested on survey and measurement data from 8 parks in Antwerp and on computational models of auditory perception. Results show that attention focusing is dominated by the change in frame of reference or expectation. In addition, a weak relationship was found between the park where persons were encountered and their view on the concept of tranquility.
Full Paper
Studies of Combination Effects of Sound on Biology and Cognition- Interdisciplinarity in Action
Mossberg, Frans
Lund University, Sweden
ABSTRACT
The Sound Environment Center at Lund University has since 2005 hosted interdisciplinary research on sound environment issues promoting exchange of ideas between researchers through research projects, interdisciplinary symposiums and publications. The center aims at developing a holistic view to a field that is scientifically fragmented and scattered. Ranging from acoustics, noise abatement and soundscape understanding, to issues of epidemiological mapping of health, biological effects, hearing and voice disorders, music and cognition the center covers a multitude of facets of sound and noise.
The work of the center is connecting to both national and international research networks and partners. Going from research to practice and change, in joint collaborations between acoustics, logopedics and cognitive science the center is exploring how memory, cognition and reception are affected by sound and noise. Current major projects focuses on health and cardiovascular issues and noise, acoustics, voice production, speech intelligibility and understanding, as well as eye-tracking studies of cognitve aspects of noise and sound exposure.
The preliminary outcome of interdisciplinary design has been positive and fruitful leading to deepened network collaborations and continuously new research projects.
Full Paper
Temporal features extraction for the binaural soundscape samples
Wang, Daiwei (1), Deng, Zhiyong (1), Li, Xinxin (1), Liu, Aili (2)
(1) College of Music, Capital Normal University, China
(2) College of Resource Environment and Tourism, Capital Normal University, China
ABSTRACT
Soundscape, earlier proposed by the Canadian composer and ecologist R. Murray Schafer in 1960s, contains a large amount of environmental information and event information for the expression of specific historic areas, the survival status of a particular nation or people, and especially, the native environment has important significance. 22 binaural recorded soundscape samples collected from Guangxi Zhuang Autonomous Region of China and their temporal features, included IACF, IACC, temporal envelope, acoustical dynamic were introduced in this paper. The information of native location, sound event and the above temporal features are also highly corresponded to the keynote, sound signal and soundmark of the soundscape. The preliminary results in this paper can provider an important theoretical and practical significance for the further extraction and analysis for the acoustical parameters of soundscapes.
Full Paper
Noise and Low frequency noise from Wind Turbines
Søndergaard, Bo
Grontmij, Denmark
ABSTRACT
Noise is a key issue when planning wind farms. The presentation will look into details in noise from wind turbines, noise measurements, noise assessment, including the Danish noise limits for low frequency wind turbine noise, and noise propagation. Development of noise and low frequency noise with the size of the turbines will be discussed. Questions like how far does low frequency noise propagate will be addressed.
Full Paper
The impact of building acoustics on speech comprehension and student achievement
Wang, Lily M
University of Nebraska - Lincoln, USA
ABSTRACT
The movement for improved classroom acoustics has primarily been grounded on studies that show how building acoustics (i.e. background noise levels and room reverberation) affect speech intelligibility, as determined by speech recognition tests. What about actual student learning, though? If students do not understand each spoken word in the classroom perfectly, can they still manage to achieve high scholastic success? This presentation will review two recent studies conducted at the University of Nebraska - Lincoln, linking classroom acoustic conditions to student learning outcomes and speech comprehension (rather than simply recognition). In the first, acoustic measurements in two public school districts in the Midwest were correlated to elementary student achievement scores. Results indicate that higher background noise levels, greater than 40 dBA, may lead to unacceptable scholastic performance in language and reading tests. The second study focuses on how room acoustic conditions impact English speech comprehension of native-English-speaking listeners in contrast to English-as-second-language (ESL) listeners, a group which includes 21% of children in the United States K-12 school system. Conclusions are that higher reverberation times and background noise levels do reduce speech comprehension in both groups of listeners, but adverse noise conditions are particularly more detrimental on ESL listeners.
Full Paper
Acoustic metamaterial panel composed of funnel-shaped cell unit having multi-band negative material properties
Cho, Sungjin (1), Kim, Boseung (1), Min, Dongki (1), Kang, Jeonghoon (1), Park, Junhong (1)
(1) Hanyang University, South Korea
ABSTRACT
This paper presents two dimensional sound-proof acoustic metamaterials having tunable multi-band negative effective mass density. The acoustic metamaterial panel was composed of many periodic funnel-shaped cell units into square lattice. Each unit cell operates as multi-band resonators. By tuning unit cell the local reflected acoustic wave was almost out of phase with the incident wave. It leads to the negative effective density and created band gap for absorbing incident sound energy without transmission. Measurement of the transmission loss and negative effective mass density was performed using four microphone methods for characterization of barrier performance.
Full Paper
Tailoring Acoustic Metamaterials to Aeroacoustic Applications
Iemma, Umberto (1), Carley, Michael (2), Pellegrini, Riccardo (1)
(1) Roma Tre University, Italy
(2) University of Bath, UK
ABSTRACT
The advent of metamaterials in acoustics is shaking-up the research community. The theoretical models and the realization technologies developed during the last decade have suddenly made possible applications that were barely conceivable before. Acoustic invisibility, perfect acoustic mirrors and lenses or ideal wave guides are now realizable with devices exploiting the potential of acoustic metamaterials. The present paper aims to investigate the applicability of such technologies in the aeroacoustic domain. The final goal of the research is the disclosure of the tremendous potential of metamaterial technologies in the abatement of civil aviation noise. The acoustic metamaterial theory developed so far is based on the assumption that the compressible medium and the scattering obstacles are at rest. This is clearly a limitation not compatible with aeroacoustic applications, where aerodynamic convection plays a fundamental role in the propagation and scattering patterns. The paper presents an original approach to extend the existing theory to the analysis of moving media and obstacles. Attention is focused on the design of a cloaking device, i.e. a metamaterial cover able to cancel the scattering of the cloaked object. Two formulations are presented, both based on the extension of the classical coordinate transformation approach to consider the existence of the mean flow. Preliminary numerical results are presented to demonstrate the effectiveness of both the approaches.
Full Paper
Noise shielding using active acoustic metamaterials with electronically tunable acoustic impedance
Mokry, Pavel (1), Steiger, Katerina (2), Vaclavik, Jan (1), Psota, Pavel (2), Dolecek, Roman (2), Marton, Pavel (1), Kodejska, Milos (1), Cernik, Martin (1)
(1) Technical University of Liberec, Czech Republic
(2) Regional Center for Special Optics and Optoelectronic Systems TOPTEC, Czech Republic
ABSTRACT
Noise pollution has become one of the most serious problems of our society. Considerable part of unpleasant noise is transmitted into the interior of buildings through large vibrating planar structures - windows with poor noise-isolation properties caused by their low flexural rigidity. In this Paper, we demonstrate and analyze a noise shielding using an active acoustic metamaterial (AAMM) with electronically tunable acoustic impedance. The AAMM consists of a curved glass plate with attached piezoelectric Macro-Fiber Composite (MFC) actuators shunted by negative capacitor (NC) circuits. Using this approach, it is possible to electronically control the effective elasticity of the MFC actuators and, therefore, the flexural rigidity of the composite structure of the AAMM. Key features that control the acoustic impedance of the AAMM have been analyzed on a simplified analytical model. Frequency dependence of the acoustic impedance and the acoustic transmission loss through the AAMM are measured and compared. Vibration modes of the AAMM are optically measured using Digital Holographic Interferometry (DHI).
Full Paper
A simple model of effective elastic properties of materials with inclusions
Skvortsov, Alex (1), MacGillivray, Ian (1)
(1) DSTO, Australia
ABSTRACT
The aim of this study is to develop a simple phenomenological model for the elastic moduli of a composite material formed by localized inclusions embedded in an elastic matrix. It is assumed that the material can be characterised by only two aggregated parameters, viz., volume fraction of inclusions and their resonance frequency within the elastic matrix. The values of these two parameters are assumed to be given (i.e. from experimental measurements) or deduced from other models (also presented in the paper). The shear wave velocity in the elastic matrix is assumed to be much smaller than the velocity of longitudinal waves. A simple analytical expression for the effective longitudinal wave velocity that is uniformly valid for the entire frequency domain is derived (including proximity to the resonance frequency of inclusions) and validated with some paradigmatic results of the mean-field theories.
Full Paper
Random Incidence Transmission Loss of a Metamaterial Barrier System
Varanasi, Srinivas (1), Bolton, J. Stuart (1), Siegmund, Thomas (1)
(1) Purdue University, USA
ABSTRACT
It has been shown previously that a panel comprising a cellular array can yield a normal incidence transmission loss in a specified low frequency range that is significantly larger than that of a homogeneous panel having the same mass per unit area. The cellular metamaterial considered consists of a periodic arrangement of unit plates held in a grid-like frame. However, when the incident sound field is diffuse, the relative advantage of the metamaterial barrier is reduced or eliminated. Here it will be shown through a sequence of experimental measurements that the relative advantage of the metamaterial barrier can be restored by creating a hybrid system consisting of a layer applied to the front surface of the material that causes sound to approach the barrier at normal incidence, and a layer on the rear surface of the material that compensates for the transmission loss minimum that normally follows the peak in a metamaterial barrier transmission loss. In the implementation considered here, the front layer consists of a lattice structure, and the rear layer consists of high performance glass fiber. The role of each of these components will be illustrated using measurements of transmission loss of a 1.2 m square panel system.
Full Paper
Special Noise Character in Noise from Wind Farms
Lenchine, Valeri V (1), Song, Jonathan (1)
(1) SA Environment Protection Authority, Australia
ABSTRACT
Noise produced by wind farms may exhibit a multitude of different noise characters, ranging from amplitude modulation, tonality and low frequency noise. The presence of the noise characters is able to increase the annoyance factor caused by a noise source significantly. A penalty to the noise levels is applied in accordance with some regulations when a noise character is detected. This paper discusses a noise character that can be described as "rumbling" that was detected during a long term monitoring program which was conducted in an area adjacent to a wind farm. The objective assessment of the data and subjective assessment of relevant audio records were performed to analyze the effect. The frequency spectra of the rumbling events indicate connection of the effect with low frequency noise and one of the low frequency components. The character was detected at low noise levels and might not be audible to a typical listener, however it is possible the character may cause an increased annoyance to people who have a higher sensitivity to the lower frequencies. Environmental conditions were also considered when discussing the occurrence of this noise character. The possible mechanism of the rumbling effect is suggested in the paper. The wind farm manufacturers may have to consider potential for low frequency impact of wind turbines and presence of prominent components at the design stage.
Full Paper
Investigating the impacts of wind turbine noise on quality of life in the Australian context: A case study approach.
McBride, David Iain (1), Shepherd, Daniel (2), Thorne, Robert (3)
(1) University of Otago, Dunedin, New Zealand
(2) Auckland University of Technology, New Zealand
(3) Massey University, Wellington, New Zealand
ABSTRACT
The WHO considers noise pollution to be of sufficient threat to public health to justify the publication of guidelines on noise effects and mitigation. 'Community noise' has largely been studied in the context of transportation and general neighbourhood noise, with exposure to wind turbine noise relatively understudied for historical, methodological, and political reasons. There also appears to be a general uncoupling of wind turbine noise from the other sources, which endows upon it an exclusivity that excuses it from the methods, guidelines, and critique used for other noise sources. This study aimed to advance understanding of wind turbine noise impacts by adopting a case study approach based on detailed information from 25 individuals, Australian adults residing rurally and within 1000-3500m of three or more wind turbines. Participants were selected on the basis of health concerns evidenced through statutory declarations or submissions to hearings. The 25 respondents compeleted a face-to-face survey measuring health-related quality of life (HRQOL) questionnaire as developed by the World Health Organisation (WHO), the 'WHOQOL-BREF'. The results were compared to normative population data and showed clinically significant reduction in HRQOL.
Full Paper
Outcome of systematic research on wind turbine noise in Japan Part 1
Tachibana, Hideki
University of Tokyo, Japan
ABSTRACT
In Japan, serious complaints about wind turbine noise have arisen from nearby residents since the commencement of large-scale construction of wind generation plants in about 2000. Regarding this new type of environmental noise problem, scientific knowledge is insufficient and no standard methods for measuring and assessing the noise have been established in Japan. To improve this situation, a research project entitled "Research on the evaluation of human impact of low frequency noise from wind turbine generators" has been conducted over the three years from fiscal year 2010, funded by a grant from the Ministry of the Environment, Japan. This project consisted of three main subjects: (1) physical research on wind turbine noise by field measurement, (2) a social survey on the response of nearby residents, and (3) auditory experiments on the human response to noises containing low frequency components. In this paper, the outcome of the research project is reviewed and standard methods for measuring and assessing the wind turbine noise are discussed.
Full Paper
Outcome of systematic research on wind turbine noise in Japan Part 2
Tachibana, Hideki
University of Tokyo, Japan
ABSTRACT
In Japan, serious complaints about wind turbine noise have arisen from nearby residents since the commencement of large-scale construction of wind generation plants in about 2000. Regarding this new type of environmental noise problem, scientific knowledge is insufficient and no standard methods for measuring and assessing the noise have been established in Japan. To improve this situation, a research project entitled "Research on the evaluation of human impact of low frequency noise from wind turbine generators" has been conducted over the three years from fiscal year 2010, funded by a grant from the Ministry of the Environment, Japan. This project consisted of three main subjects: (1) physical research on wind turbine noise by field measurement, (2) a social survey on the response of nearby residents, and (3) auditory experiments on the human response to noises containing low frequency components. In this paper, the outcome of the research project is reviewed and standard methods for measuring and assessing the wind turbine noise are discussed.
Full Paper
AFLoNext - A European Contribution to Airframe Noise Control
Bauer, Michael (1), Büscher, Alexander (2), Pott-Pollenske, Michael (3)
(1) Airbus Group Innovations, Germany
(2) Airbus Operations GmbH, Germany
(3) DLR, Germany
ABSTRACT
FLoNext is a project of four years duration, funded by the European Commission within the Seventh Framework Programme. The project's main objectives are proving and maturing highly promising flow control and noise reduction technologies for novel aircraft configurations, to achieve a big step forward towards improved aircraft's performance and thus reducing the environmental footprint. The project consortium is composed by 40 European partners from 15 countries. One of the six technology streams, which are forming the scientific concept of AFLoNext, is concerned about the mitigation of airframe noise during approach and landing, generated on flap and undercarriage and through mutual interaction. Following the success of previous achievements on European level, accomplished in projects such as TIMPAN, SILENCER and OPENAIR, low noise technologies for the reduction of landing gear/flap interaction and flap side edge noise are going to be further developed in wind tunnel testing with a common goal: The proof under real operational conditions in flight test at the end of the project.This paper is to give an overview on the intended approach in AFLoNext and the expected results related to aircraft acoustics and impact on aerodynamic performance.
Full Paper
European aviation noise research network (X-NOISE)
Collin, Dominique
Snecma, France
ABSTRACT
The X-NOISE Coordination Action, through its network structure and comprehensive workplan involving experts groups, scientific workshops, international cooperation seminars and a common information system, addresses the noise challenges faced by Aviation. As such, the project scope significantly contributes to the objective of reducing Aircraft Noise by 10 dB per operation as set by the ACARE 2020 Vision, while addressing key factors associated with Airport Noise issues. A dedicated Aviation Noise Research Network has then been established, developing its activities along a 3-Pillar approach. (1) Definition, coordination and assessment of a European research strategy aimed at meeting the ACARE noise targets. (2) Dissemination and communication of the European research effort scientific and technological achievements as well as issues and priorities for the future. (3) Improved integration of European research community activities in the field of air transport related noise research.
Full Paper
OPtimisation for low Environmental Noise impact AIRcraft - OPENAIR
Kors, Eugene (1), Collin, Dominique (1)
(1) Snecma, France
ABSTRACT
This template provides instructions to authors of papers to be included in the Proceedings of INTER-NOISE 2014, which will only be published on a USB memory stick. These instructions are in the format to be used for ALL papers, which shall be submitted ONLY as a Portable Document Format (PDF) file. An abstract is required at the start of all papers and shall contain at least 100 words, but not more than 200 words. The abstract shall not include equations, images, numbered references, or footnotes. Abstracts will be printed in the Conference Abstract Book to help attendees plan their days at the Conference. Authors must upload the Abstract as well as the full paper manuscript for the complete paper via the Conference Website. A maximum of three keywords shall be added below the abstract to provide easy access to related papers in the Proceedings. At least one classification number from the I-INCE Classification of Subjects shall appear on the first page.OPENAIR is currently the main Level 2 European project working on aircraft noise reduction. As such, it is a key element of the European aircraft noise research roadmap as developed by the X-NOISE Coordination Action which aims to reduce Aircraft Noise by 10 dB per operation as set by the ACARE 2020 Vision.Over the years, a significant effort has been conducted in the field of source noise reduction technologies, marking a first step towards the achievement of the ACARE targets through the Silence(R) project.As part of the European 7th Framework Program, OPENAIR started on 1st April 2009 as a program on aircraft noise reduction with a total budget of 30 million Euros, 60% funded by the European Commission. OPENAIR aims to deliver a 2.5 dB noise reduction for both engine- and airframe noise sources, beyond the SILENCE(R) achievements. To do so, OPENAIR focuses on the validation of new technologies at TRL5, such as electronically assisted solutions, designs exploiting improved Computational Aero-Acoustics, new affordable absorbing materials and airframe noise solutions. In order to keep an unbiased view on results, OPENAIR uses the Aircraft Noise Technology Evaluation process ANTE. A summary of the OPENAIR research topics will be provided.
Full Paper
Fundamental indirect noise generation by interactions between entropy, vorticity and acoustic waves in the context of aero engine applications
Ullrich, Wolfram Christoph (1), Schulze, Moritz (1), Sattelmayer, Thomas (1)
(1) Technische Universität München, Germany
ABSTRACT
In aero engines indirect noise is released by the acceleration of entropy and vorticity waves in the turbine, which are in turn created mainly further upstream in the combustor by unsteady combustion. Recent studies show that these interactions contribute substantially to the total emitted core noise. Consequently a detailed knowledge of the sources of entropy and vorticity waves and their interactions with mean flow and acoustics is essential for the efficient development of technologies to reduce indirect noise. In this study, a generic convergent-divergent nozzle configuration is considered as a simplified model of the transonic turbine vane flow to study entropy noise as well as the acoustic scattering behavior. A two step numerical approach is applied consisting of RANS mean flow simulations and succeeding acoustic simulations in frequency domain based on linearized Navier-Stokes equations. Source terms for both waves are deduced from linearized entropy and vorticity equation and evaluated spatially. Important interactions between entropy, vorticity and acoustic waves and the mean flow are highlighted and confirmed by an energy analysis. This analysis can be applied to real aero engine combustors and turbines and enables to quickly identify the impact of the different source mechanisms on indirect noise.
Full Paper
The evolution of noise policy and noise management in England during the life of the UK\'s Institute of Acoustics
Grimwood, Colin (1), Turner, Stephen (2)
(1) CJGEM, UK
(2) Defra, UK
ABSTRACT
The UK's Institute of Acoustics is 40 years old this year. One year before it was founded, the first UK Government guidance document on Planning and Noise was published. That year also saw the advent of the Land Compensation Act which allowed the Noise Insulation Regulations to be laid which provided a means for compensating those affected by noise from new roads. In the same year as the IOA was founded, the Control of Pollution Act was published consolidating the statutory noise nuisance regime and the following year saw the first version of BS 5228 - the code of practice on construction noise and the Noise Insulation Regulations revised. This paper will examine the evolution of noise policy and noise management in England during the lifetime of the IOA including the publication, during early 2014 of new Planning Practice Guidance on Noise.
Full Paper
Progress on environmental noise policies from 2008-2013 in Asia and the world
Schwela, Dietrich H (1), Finegold, Lawrence S (2), Gjestland, Truls (3)
(1) Stockholm Environment Institute, University of York, UK
(2) Finegold & So, Consultants, USA
(3) SINTEF, Norway
ABSTRACT
This paper provides a review of international progress on environmental noise mitigation policies and strategies, best practices and guidelines for environmental noise management. A considerable amount of relevant documents in many countries on these topics were published in the last five years. Much of this progress was made in the European Union and the World Health Organization, although other areas of the world demonstrated a continuing commitment to improvement on these issues, especially in the United States, Japan and Vietnam. These topics are particularly important because they embody the transfer into policies and legislation of expert work on the effects of noise exposure. In addition they address the vital area of the benefits of noise abatement. The latter focus area includes topics such as economic costs of environmental noise abatement and the benefits of adequate and affordable environmental noise mitigation policies in terms of avoided health and other costs, which is crucial for governments to implement strategies and policies for environmental noise management.
Full Paper
Challenges in Planning against Road Traffic Noise in Hong Kong
Wu, Marco (1), Ng, Isaac (1), Szeto, Wing Kwok (1), Yeung, Maurice (1)
(1) Environmental Protection Department, Hong Kong
ABSTRACT
Hong Kong is one of the most densely populated metropolitan cities in the world in which road traffic noise is the major environmental noise problem. Given the scarcity of land and distinctive compact cityscape of Hong Kong with major roads running near high-rise residential buildings, traffic noise impact has become a huge challenge to overcome in the course of increasing housing supply to meet the demand of the society. With the space availability and other technical concerns, at-sources mitigation measures, e.g. roadside noise barrier, may not always be the most suitable ways to reduce noise. This paper will give an account on how the traffic noise problems to new residential development in Hong Kong are minimized with illustration of practical examples on effective noise mitigation measures provided at the housing development. Also from the planning procedures angle on how the noise mitigation measures are eventually implemented and materialized. The government's effort in putting forward innovative noise mitigation measures in resolving traffic noise problem in residential development, by ways of launching a web-based database for sharing successfully implemented noise mitigation designs and participating in studies of innovative building envelop designs, will also be discussed.
Full Paper
A Metric Matrix Establishment for Cases Studies on the Effectiveness of the Key Environmental Protection Policies for Transportation Pollution Control
Zhang, Jiping (1), Schomer, Paul D (2), Buret, Marc (3), Zhang, Lei (1), Wu, Dian (1), Boyle, James (2)
(1) Zhejiang Research & Design Institute of Environmental Protection, China
(2) Schomer and Associates, Inc., USA
(3) VicRoads, Australia
ABSTRACT
In a study of the Effectiveness of the Key Environmental Protection Policies for Road Traffic Noise Control, the authors discussed 20 international case studies of road traffic and noise management. Although the key international environmental policies for road traffic noise control in developed countries are very technologically, economically, legally, and sociologically mature, these policies do not always result in compatible land use: roadways and highways are still built too close to existing residential areas, and vice versa. In China these issues are exacerbated due to its rapid urban growth and industrial expansion. In this paper, the authors expand their study to include non-noise policies (air pollution, public participation in the planning process, and other important factors) but the noise & vibration are the first impact metrics (e.g. airport, railway, shipping), and suggest a multi-dimensional matrix for such cases studies. At last, an airport case in China is employed to show the sharpened metric matrix emphasizing the compatible land use, because the noise metric dominates to the other ones in airport transportation construction demonstrating the matrix effectiveness. And the future work would be expanded to all transportation types cases.
Full Paper
A low-budget road traffic noise model for individual building evaluation - a case study in Western Australia
Felder, Martin (1), Burgess, Marion (2), Arnold, Jörg (3)
(1) Gebäudeanayse Martin Felder, Switzerland
(2) UNSW Canberra, Australia
(3) Bauhaus-University Weimar, Germany
ABSTRACT
The primary function of the project was developed to a nationwide traffic noise immission model, using as a case study a major city at the west coast of Australia (Perth WA). In this framework the relevant acoustic input parameters were prepared and verified by measurements during the process on site. The concept originates from the consideration, that a wide range of technologies and necessary information about the model treatment becomes available nowadays by internet. Much of this information is provided free-of-charge. This project used geoinformation for the terrain and the internet for details of the buildings. Some noise measurements were taken on site, to compare the measured traffic noise to the software based traffic noise immission model. In addition, traffic counts were also done to verify the traffic volumes. The project describes the ability, to create a traffic noise model in a very simple way, by means of a concrete application, namely traffic noise impact for a city area of Perth Western Australia.
Full Paper
Lessons from round 2 noise mapping in England
Hepworth, Peter (1), Shilton, Simon (2), Jones, Nigel (3), Burdett, Matthew (3)
(1) Hepworth Acoustics Ltd, England
(2) Acustica Ltd, England
(3) Extrium Ltd, England
ABSTRACT
The second round of noise mapping required under the EU Environmental Noise Directive has been completed. Lessons learnt during the initial round of noise mapping led to some differences in approach to the second round of mapping. Some of the changes have been contractual/organisational and have been made to facilitate greater efficiency in the production of noise maps. Other changes have been implemented to produce a higher level of comparability between different noise maps. This paper considers the differences in approach for Round 1 and Round 2 road and railway noise maps produced for the English government. The reasons for the changes are discussed and the outcomes that resulted from the changes are reported.
Full Paper
A web-based approach for the evaluation of acoustic performance of development designs and assessment of performance of mitigation elements
Hoar, Christopher F J (1), Wong, Kin Man (1), Noor, Noor Azlan Mohammed (2)
(1) NGIS, Hong Kong
(2) Universal Quantum Forces Sdn Bhd, Malaysia
ABSTRACT
Maximising the community's investment in efficient transportation networks is the cornerstone of sensitive development, helping businesses and families thrive. However, meeting the legislative requirements around noise and air pollution issues has significantly increased the workload for national, state and local governments, authorities and industry. Web-based spatial and 3D visualization technology can be used to assist planners, engineers, architects and environmental practitioners to rapidly evaluate the acoustic performance of different development design options and noise mitigation strategies. The ODEN platform discussed in this paper provides an easy to use web-based interface through which a number of noise and air quality issues can be examined and addressed. These include assessment of the acoustic environmental baseline, performance of design options, comparison of mitigation strategies and quantification of impact on population. The system dramatically reduces the time and resources traditionally required to perform such analyses allowing planners, engineers and architects to more effectively deliver projects with an improved acoustic environment.
Full Paper
Fast traffic noise mapping of cities using the Graphics Processing Unit of a personal computer
Salomons, Erik M (1), Zhou, Han (1), Lohman, Walter J A (1)
(1) TNO, The Netherlands
ABSTRACT
Traffic noise mapping of cities requires large computer calculation times. This originates from the large number of point-to-point sound propagation calculations that must be performed. In this article it is demonstrated that noise mapping calculation times can be reduced considerably by the use of parallel computation on the Graphics Processing Unit (GPU) of a personal computer. Comparisons are presented between a GPU implementation and a conventional CPU implementation for various urban areas, from which a GPU speedup factor of 720 is obtained (compared with a single CPU). The complete traffic noise map of Amsterdam is calculated with the GPU implementation in 2 h. Local modifications of the noise map, for example to investigate the effect of a new building or a road, are calculated in a time of the order of a minute.
Full Paper
Statistical Method for an Assessment of Actions against Noise and Air Pollution in Order to compare the total Improvement in an Investigation Area
Zacharias, Frank-Christian (1), Kunka, Rainer (1), Hoar, Christopher F J (2)
(1) Thüringer Landesanstalt für Umwelt und Geologie Jena, Germany
(2) NGIS China Ltd., Hong Kong
ABSTRACT
In accordance with the German regulation VBEB, LIMA provides intuitive methods for the evaluation of different planned actions. Noise and air pollution maps used alone are lacking in that they do not show any statistical evaluation of the quality of the actions. Actually, while the reduction of immissions is relevant, the reduction in numbers of exposed inhabitants after vs before any action is the most important evaluation criteria. In the following, we define the adapted statistical method for air pollution impact evaluation. All façades longer than 5m can be broken down into sub facades. For each part of the façade, a receiver point is calculated. LIMA determines the positions of the receiver points automatically. For noise mapping, we recommend 5 m or 10 m grid size, for air pollution mapping grid size can be fixed from 2 m up to 10 m. From the regular grid results, LIMA fetches by a sophisticated interpolation nicely fitted proper values to the necessary receiver points; this method is proved since years. The user is free to decide whether using the exact number of inhabitants for each building or using a statistical distribution of inhabitants proportional to volume of a building derived from the whole number of inhabitants in the investigation area.
Full Paper
Dispersion diagrams of a water-loaded cylindrical shell obtained from the structural and acoustic responses of the sensor array along the shell
Jung, B K (1), Ryue, J (2), Hong, C S (3), Jeong, Wei Bong (1), Shin, K K (4)
(1) Pusan National University, South Korea
(2) University of Ulsan, South Korea
(3) Ulsan College, South Korea
(4) Agency for Defence Development, South Korea
ABSTRACT
In order to analyze the vibration and the sound radiation from the waveguide structures, it is important to understand the dispersion relations of the waves sustained in the waveguides. By using the sensor arrays mounted on the surface of the waveguides, these dispersion characteristics would be constructed from the structural and acoustic responses at the sensor locations. In this study, the waveguide finite and boundary element method is adopted to predict the dispersion curves for a water-loaded cylindrical shell. The structural responses and near-field acoustic responses of the shell are used to create the dispersion diagrams and the results are compared. Also the effect of the sensor spacing is examined for the two different spans. It was found from this study that the respective dispersion curves constructed from the structural and acoustic signals are considerably different. Also it was seen that the spatial aliasing takes place in the dispersion diagram as the sensor span grows.
Full Paper
Acoustic forcing of flexural waves and acoustic fields for a thin plate in a fluid
McMahon, Darryl
DSTO, Australia
ABSTRACT
Consistency with conservation of energy for coupled acoustic fields and plate flexural waves, discussed in another paper for this conference, is used to derive the amplitude and phase of flexural and acoustic waves for an infinite thin plate - fluid system excited by an incident acoustic plane wave. The acoustic interaction of the plate - fluid system is defined by 1. specula reflection from the plate surface, 2.transmission through the plate material and 3. plate flexural waves taking into account fluid loading. This reproduces the well-known peak in plate flexural wave amplitudes above the coincidence frequency where the trace wavenumber of the incident acoustic plane wave along the plate equals the plate - vacuum flexural wavenumber. This is essentially a resonance with the resonant frequency that varies with the direction of the incident plane wave. The width of the resonance is governed by fluid loading which manifests as radiation damping of the flexural waves. It is found that flexural waves affect the acoustic reflectivity of the plate through coherent interference of the acoustic field from flexural waves with the specula reflected field, but only if there is a nonzero phase shift in specula reflection. Energy conservation considerations predict that a plate becomes acoustically soft close to the resonance condition. A simple formula for the approximate resonance width is also derived.
Full Paper
Acoustic and flexural wave energy conservation for a thin plate in a fluid
McMahon, Darryl
DSTO, Australia
ABSTRACT
Although the equations of flexural wave motion for a thin plate in a vacuum and a fluid are well known, it is not easy to find a discussion of energy conservation for plate flexural waves, particularly "leaky" waves where a plate and fluid can exchange energy. Nor are formulae easily found for acoustic and flexural wave kinetic energy density, potential energy density and energy density flux including the effect of leaky waves. This paper derives formulae for acoustic and flexural energy densities and energy density fluxes, and finds the energy conservation equation for the coupled thin plate - fluid system
Full Paper
Separation of non-stationary sound fields using single layer pressure-velocity measurements
Bi, Chuan-Xing (1), Geng, Lin (1), Zhang, Xiao-Zheng (1)
(1) Hefei University of Technology, China
ABSTRACT
This paper presents a sound field separation technique using single layer pressure-velocity measurements to extract the non-stationary signal generated by a target source in the presence of disturbing sources. In the technique, the time-independent pressure and particle velocity signals on one measurement plane are first measured; then the pressure signal generated by the target source alone can be extracted by a simple superposition of the measured pressure and the convolution between the measured particle velocity and the corresponding impulse response function. An experiment involving three speakers driven by a non-stationary signal was investigated, where a pressure-velocity probe was used repeatedly to measure the time-independent pressure and particle velocity signals on the measurement surface and a trigger was used to keep the measured signals the same at each measurement. The experimental results demonstrate that the proposed technique is effective in extracting the desired non-stationary sound field generated by the target source alone from the mixed one both in time and space domains.
Full Paper
Comparison of patch acoustic holography methods for confined space
Havránek, Zdeněk (1), Beneš, Petr (1), Klusáček, Stanislav (1)
(1) Brno University of Technology, Czech Republic
ABSTRACT
Localization and characterization of noise and vibration sources through measurement of sound fields radiated from vibrating structures plays an important role in vibration diagnostics. Sound pressure field measured in closed distance to the source with a microphone array is then inversely processed with the suitable near-field acoustic holography method to obtain the estimation of sound field very near the identified source surface. Several restrictions apply when measurement is performed in non-anechoic conditions and with the array smaller than the examined source. In these cases patch holography methods with sound field separation technique should be used. The Equivalent Source Method (ESM), Statistically Optimized Near-field Acoustical Holography (SONAH) and iteratively enhanced Fourier transformation based procedure are examples of such methods. In this paper an extensive comparison of these source identification methods has been carried out while other disturbing sources affect the acquired data. Experimental evaluation of the methods has been performed in ideal anechoic conditions and further in disturbing environment. Real measurement data has been obtained with double layer planar rectangular microphone array with MEMS transducers and the results of principal source identification accuracy for all methods have been presented. Some practical aspects of applicability of each method are also discussed.
Full Paper
Research on eigenfrequency shifts due to cracks in cylindrical structures and the application in non-destructive testing
Stache, Martin (1), Guettler, Marcus (1), Marburg, Steffen (1)
(1) Universität der Bundeswehr München, Germany
ABSTRACT
This paper presents numerical and experimental studies on modal behavior of cylindrical, beam-like lightly damped structures having circumferential cracks with variable position, width and depth. In the numerical investigation utilizing Finite-Elements a discretization strategy is worked out that enables a three-dimensional crack representation. The experimental setup uses a Laser Scanning Vibrometer in the frequency range between 0 - 40 kHz. The major challenges to achieve adequate precision of the experimental data exist in the realization of a broadband impulse excitation and support conditions for repeatable measurement conditions. Numerically as experimentally the first 15 mode shape pairs with the corresponding eigenfrequencies are identified. The model updating is performed for the elastic parameters and appropriate boundary conditions to minimize the deviation between measured and calculated eigenfrequencies. The acquired data serves for the implementation of a damage identification procedure in which the geometrical crack properties are identified. The deviation between real and determined crack positions is lower than 0.3 % for crack cross-section ratios less than 7 %.
Full Paper
Approximate model of sound source in consideration of evanescent waves in far-field acoustical holography
Wang, Ziteng (1), Yang, Diange (1), Miao, Feng (1), Wang, Rujia (1), Wen, Junjie (1), Lian, Xiaomin (1)
(1) Tsinghua University, Beijing, China
ABSTRACT
Far-field acoustical holography methods reconstruct the sound fields mainly based on the simple point source model because of the loss of abundant information compared with near-field acoustical holography (NAH). It brings problems that the reconstructed sound sources are different from the actual measured sound sources especially because of the evanescent waves which attenuate rapidly in the near field. In the recent study, we establish the approximation formulation of evanescent wave propagation which suggests that evanescent wave can be considered as the interference of dipole model and quadrupole model with different weighting factors distributed on the incident wave-front. Without the evanescent wave component, the constructed sound sources are actually the components that are effective in the far-field and we proposed the concept of "far-field effective sound source" to show its physical meanings. With simulations and actual experiments with known speakers, the approximation method of sound source model is validated and the far-field acoustical holography has been improved to achieve more accurate quantitative reconstruction results. The study explored the evanescent wave which is hard to capture and for engineering practice, this research can give more accurate reconstruction as well as the approximation.
Full Paper
Vibration rendering on a thin plate by actuator array on the boundary
Woo, Jung-Han (1), Ih, Jeong-Guon (1)
(1) KAIST, Korea
ABSTRACT
Generation of localized vibration on the display panel in the mobile electronic devices is needed for transferring the tactile sensation to the users. When the actuators cannot be positioned at the central part of the panel due to the interference with electronic components, the only choice for the actuator locations is the edge of the panel. To generate a rendered distribution and pattern of the vibration, eigenfunction expansion and superposition can be used as the basic principle. The target vibration field consists of the hot and cold zones. In the hot zone, high amplitude vibration should be felt by the user, and, in the cold zone, the vibration amplitude should be tranquil not to incur any tactile sensation. A general inverse method to determine the proper weighting for each actuator in the array is pursued. Experiments are conducted on a thin rectangular panel and employing small moving-coil actuators. Performance indices for evaluating the control results are suggested based on the threshold and difference limen of tactile feeling. Performances of vibration localization varying the location of hot zone and the number of involved modes are evaluated, and the measured and rendered vibration targets match very well.
Full Paper
Influence of design and leakages of the window-wall connection on the sound insulation.
Ferk, Heinz (1), Buchegger, Blasius (1), Meissnitzer, Marlon (1)
(1) TU Graz, Austria
ABSTRACT
Sound insulation performance of enclosures like lightweight exterior wall systems depends on the one hand on the sound insulation of the exterior wall design, on the other hand on the sound insulation of windows and doors and finally on the design of the connections between. An investigation done under the laboratory conditions shows, that the influence of the connection design of the window element to the wall can reduce the resulting sound insulation remarkable, especially if there are higher requirements for the sound insulation against exterior noise. The effect of leakages on reducing sound insulation also depends as expected on the type of material that is used for thermal insulation and air tightness and posssible leackages. Moreover also the position of leakages influences the result of the sound insulation - in some cases the wedges that are used to get the window in the right position are incorrectly processed and so sometimes have to be removed before finishing the connection and mounting of the window sills, with the consequence of a bad sound insulation performance. A handy tool was developed, based on a modified sound intensity method, that can help to find such leackages quickly. Finally the different methods in ISO EN 10140-1 for the estimating of the sound insulation of joints were discussed. Investigation shows, that it is necessary to be careful in designing such connections and also in choosing the right measurement or evaluation method to get reliable results for an estimation of the sound insulation performance of connections.
Full Paper
A model based on loudness level to describe airborne sound insulation
Neubauer, Reinhard (1), Kang, Jian (1)
(1) University of Sheffield, UK
ABSTRACT
Sound transmission between units is one of the biggest complaints among apartment building residents today. Since living noise is an increasing problem particularly between dwellings there is a need for a method of assessing airborne sound insulation between rooms. In many practical cases, however, the objective measures of the airborne sound insulation using procedures in standards are not in agreement with the subjective assessment. This paper describes a calculation scheme based on loudness level linked with specific fluctuation strength, yielding a weighted normalized loudness level difference Lnor,w. By analysing the difference between standard airborne sound insulation values and the introduced weighted normalized loudness level difference, it is revealed that the sound pressure level that is transmitted through a partition contains important details concerning subjective assessments. It is shown, that a simple level difference does not exhibit the effect of a given signal to the frequency-dependent airborne sound insulation curve, while using Lnor,w, a significant effect can be observed, in terms of both computed and measured results.
Full Paper
Improvement of sound insulation performance at low frequencies by several fibrous absorbers in lightweight double leaf partition
Sugie, Satoshi (1), Yoshimura, Junichi (1), Iwase, Teruo (2)
(1) Kobayasi Institute of Physical Research, Japan
(2) Niigata University, Japan
ABSTRACT
Sound insulation performance is generally increased by installing a fibrous absorber such as glass wool into cavity of double leaf partition. It usually increases further as the thickness and density of fibrous absorber increase. However, installing the absorber decreases occasionally the sound insulation. In this study, we have measured the sound insulation performance by use of test facility in which the fibrous absorber in the cavity could be replaced without removing boards from studs. From the results, we have clarified the relationship between the parameters, such as thickness and density, of fibrous absorber and the sound insulation performance at low frequencies. The performance is reduced at frequency bands not greater than the mass-air-mass resonance frequency as installing glass wool into the cavity. It is also presented that the performance does not absolutely increase with increasing the bulk density in the frequency range from 125 Hz to 250 Hz. The proper value of the bulk density is about 24 kg/m3 for improvement of the sound insulation.
Full Paper
Parametric study of direct airborne insulation of wood stud walls in midrise construction
Zeitler, Berndt (1), Schoenwald, Stefan (2), King, Frances (1)
(1) National Research Council, Canada
(2) Empa Swiss Federal Laboratories for Materials Science and Technology, Switzerland
ABSTRACT
There has been a proposal in Canada to increase the maximum allowable height of wood framed construction in the National Building Code of Canada (NBCC) from 4 stories to 6 stories. Design of taller buildings will lead to a change in the details of the walls that have to withstand the higher axial and lateral loads. However, also requirements of other building physics disciplines, one of those being the sound insulation, still have to be met. In the study presented here various assemblies that meet the higher load requirements are compared for direct airborne sound insulation. Parameters that were modified include: sheathing membranes, stud arrangement, stud depth, and resilient channels. Some of the wall design variants that work well structurally have very poor sound insulation properties and most of them require the use of resilient channels to obtain somewhat acceptable sound insulation properties. These and more results will be presented here.
Full Paper
A coherent image source method for sound prediction in long spaces with a sound absorbent ceiling
Min, Hequn (1), Chen, Yan (2), Qiu, Xiaojun (2)
(1) Southeast University, Nanjing, China
(2) Nanjing University, China
ABSTRACT
Sound absorbing boundaries can attenuate noise propagation in a long space, but they may lead the sound field hard to be accurately predicted. This paper presents a coherent image source model for sound field in long spaces with a sound absorbing ceiling. In this model, the reflections on the absorbent boundary are separated from those on reflective ones during applying refection coefficients. The model is compared with the classic wave theory, the existing coherent ray-based model and a scale-model experiment. The results show that the proposed model has considerate accuracy and distinct advantage over the existing model for sound prediction in long spaces with an absorbent ceiling.
Full Paper
A trial on calculating the equivalent reflection coefficient by acoustic distance measurement method based on phase interference in the actual sound actual field
Nakasako, Noboru (1), Neki, Yuma (1), Nakayama, Masato (2), Shinohara, Toshihiro (1), Uebo, Tetsuji (3)
(1) Kinki University, Japan
(2) Ritsumeikan University, Japan
(3) WADECO Co., Japan
ABSTRACT
Since the distance to target is very important information, we have proposed an acoustic distance measurement (ADM) method using a standing wave, which is generated by interference between transmitted and reflected waves. The proposed method is very simple in that the distance between the microphone and the target is estimated as the peak position of the range spectrum (i.e., the absolute value of the Fourier transform with respect to the power spectrum of the observed wave). The ADM method can be used to measure distance under the assumption that the transmitted and reflected waves are plane waves, even if the target is placed in a very close range and the reflection coefficient of the target is unknown. The ratio of the magnitude of the reflected wave to that of the transmitted wave (which is referred to as the equivalent reflection coefficient) can be estimated for the special case of a single target. The equivalent reflection coefficient contains the reflection coefficient and the distance decay. The present paper describes a new method for calculating the equivalent reflection coefficient using the ADM method based on phase interference in the actual sound field. We also examine the validity and effectiveness of the proposed method through a computer simulation and by applying the proposed method to an actual sound field.
Full Paper
Absorption modeling with ensemble averaged impedance for wave-based room acoustics simulations
Otsuru, Toru (1), Tomiku, Reiji (1), Okuzono, Takeshi (2)
(1) Oita University, Japan
(2) Kobe University, Japan
ABSTRACT
With the rapid progress of computers, wave-based room acoustics simulations like finite element method have come to be applicable onto many practical problems on acoustics. Generally, such methods can calcu- late sound fields quite accurately provided their boundary modelings are given appropriately. Although the absorption on the boundary can be modeled efficiently by using surface impedance, the impedance database is not accumulated yet. It is due to the difficulty in the practical measurement of surface impedance of materi- als at field conditions. To overcome the difficulty, the authors proposed a way to measure surface impedance by using ensemble averaging technique. In this paper, the basic concept of the authors' measurement method of surface impedance is summarized first. Then, an application of the measurement technique onto a realistic sound field in a cafe-restaurant is shown, and comparisons with the other methods are given to prove the effectiveness of the technique.
Full Paper
A technique based on the equivalent source method for measuring the surface impedance and reflection coefficient of a locally reacting material
Zhang, Yong-Bin (1), Lin, Wang-Lin (1), Bi, Chuan-Xing (1)
(1) Hefei Univesity of Technology, China
ABSTRACT
A technique based on equivalent source method (ESM) is developed in this paper for measuring the surface impedance and reflection coefficient of a test material. The technique requires the measurement of complex pressures on two parallel planes between the sound source and the test material. If the sound source has rotational symmetry, the measurement on two parallel lines is sufficient. The sound pressure and normal component of particle velocity on the surface of the test material can then be calculated by using the ESM. The technique is similar to that proposed by Tamura in which the spatial Fourier transform rather than the ESM is used. Numerical examples are given to compare the proposed technique with the Tamura method, and the results show that a smaller measurement aperture is required and the measurement noises are easier to be controlled when using the proposed technique.
Full Paper
Vehicle noise functional performance indicators using tire sound intensity
Donavan, Paul (1), Janello, Carrie (1)
(1) Illingworth & Rodkin, Inc., USA
ABSTRACT
Tire noise plays an important role in the noise performance of light vehicles for both interior and exterior noise. Tire noise sound intensity can be considered as a functional performance indicator for both types of noise. Databases of vehicle interior noise and exterior pass-by noise combined with the corresponding on-board sound intensity (OBSI) results were assembled to examine the relationships between these types of data. Relationships or objective "filters" were developed for relating OBSI to interior noise quantified in terms of A-weighted sound pressure level, loudness in sones, speech interference level, and percent articulation. Relationships between OBSI and interior structure-borne road noise were also examined. For exterior noise, a filter shape relating controlled pass-by measurements to OBSI data were developed for assessing community noise due to different pavements. This filter can also be used to quantify the increased exterior noise produced by tires under acceleration with applied torque. The principles described can be used in the vehicle noise development process for interior noise and for diagnosing the contribution of tires to regulatory pass-by noise, such as defined in the ISO 365 test procedure.
Full Paper
Verification of contribution separation technique for vehicle interior noise using only response signals
Hirano, Tomohiro (1), Yoshida, Junji (1)
(1) Osaka Institute of Technology, Japan
ABSTRACT
In this study, a contribution separation technique using only response signals were considered for an analysis of vehicle interior noise. Independent component analysis (ICA) was applied for the technique. To verify and consider the applicability of the method in contribution separation, vehicle engine, road, and wind noise sources were combined artificially to simulate vehicle interior noise and applied ICA to these signals for contribution separation. The result shows the contribution could not be obtained correctly by the permutation problem in which the correspondence relationship between calculated and actual contributions is not kept along frequency. A solution technique was then proposed to solve the problem using the characteristics of sound source. As a result, the technique with the method could calculate accurate sound source contributions using only response signals.
Full Paper
Development of a prototype system to evaluate of contribution rate of each noise source in road traffic noise
Houzu, Hiroyuki (1), Sakamoto, Ichiro (1), Nishi, Takahiro (1), Ishihama, Masao (2), Sawatari, Katsumi (3)
(1) National Traffic Safety and Environment Laboratory, Japan
(2) Kanagawa Institute of Technology, Japan
(3) ONO SOKKI CO.,LTD., Japan
ABSTRACT
In Japan, the achievement of environmental standards for noise is evaluated by long-term average sound level. Therefore, it is quite difficult to identify the factors of exceeding the regulatory limit. This study aims to develop a system that enables to conduct a separate measurement of each noise source and an evaluation of each source. By the evaluation of contribution rate of each noise source in roadside noise, it is possible to define priorities for countermeasures to deal with. As the first step of the system development, this paper introduces the development of prototype system, reporting on the configuration of the system and the results of verification tests.
Full Paper
Mechanism of Noise Generation on Outer Rotor Motor
Ikeda, Kazumasa (1), Semura, Junichi (1), Ohzawa, Tsukasa (1)
(1) DENSO CORPORATION, Japan
ABSTRACT
A rotor and a stator of an outer rotor motor often resonate with electromagnetic force working between them. Sometimes resonating rotor and stator cause irritating magnetic noise. When they make noises with their resonance, noise from the stator shows its resonance frequency. However, noise from the rotor shows different frequency from its resonance frequency. To clarify the mechanism of the phenomenon, surface vibration of the rotor during rotation was measured by using cylindrical microphone array that covered the entire rotor and was calculated by using advanced non-stationary conformal mapping technology by Equivalent Source Method (ESM) approach. As a result, it was found that the rotor is resonating with rotation and the amplitude of air vibration is modulated on the surface of the rotor.
Full Paper
Parameter quantification for evaluation of vehicle\'s impulsive BSR noise
Lee, Sinyeob (1), Kwak, Yun-sang (1), Kim, Boseung (1), Lee, Jongho (1), Park, Junhong (1)
(1) Hanyang University, South Korea
ABSTRACT
In vehicles, consumer complains against BSR (buzz, squeak, rattle) noises are increasing. The BSR noises includes continuous or impulsive sounds depending on the generation mechanism. The evaluation method for rating the annoyance of BSR noises is required after taking these irregularly and periodicity. For continuous sounds, conventional Fourier transfer provides sufficient information on the spectral characteristics. However, the spectral information for impact sounds is difficult to be identified from Fourier transforms. In this study, Prony's method is applied to evaluate the spectral components (frequencies and decay ratio) of impact noises. The sinusoidal and exponential models fits a sum of damped complex exponentials. Through the auditory test, the noise level and attenuation ratio were identified as important factors influence annoyance. This attenuation term increased the annoyance of BSR sounds.
Full Paper
The Dutch Road Noise Mitigation Program
Faber, Nico
AnteaGroup consultancy, The Netherlands
ABSTRACT
In July 2012 a new law on noise pollution along major roads entered into force in the Netherlands. This law contains three important elements of new noise legislation:a) the introduction of noise production limits;b) the stimulation of source related noise measures;c) the reduction of situations with high noise exposure.The first two elements deal with the prevention of new high noise levels occurring after introduction of the law. The third element concerns the reduction of noise for existing situations that already experience high levels of road noise from major roads in the Netherlands. To deal with the third element the Dutch National Road Authority developed the Dutch "Road Noise Mitigation Program" with a total budget of 275 million Euros. This program consists of three projects in which noise mitigation measures (noise reducing pavements, noise barriers, noise insulation of houses) will be taken along all major roads in The Netherlands. This paper deals with the first pilot project MJPG 1 of the program and discusses the first's results. In this project the Dutch cost benefit analysis method is used as a decision tool for designing noise measures.
Full Paper
Value for Money in Road Traffic Noise Abatement
Milford, Ingunn (1), Aasebo, Sigve Jarl (2), Strommer, Kjell (3)
(1) Multiconsult, Norway
(2) Visy, Norway
(3) Transport Administration, Sweden
ABSTRACT
Road traffic noise is a significant environmental problem. The purpose of this work by CEDR Project Group Road Noise 2, has been to provide support to National Road Authorities (NRAs) when developing strategies and plans for future noise abatement in order to reduce noise annoyance. To provide a recommendation on which strategy would be most beneficial to society in general, this project has focused on reduction in noise annoyance and the associated cost of implementing various noise abatement measures. There are almost 100 million inhabitants in Europe annoyed by road traffic noise. With an investment of EUR 6 billion over a 20 year cycle in a range of different possible noise mitigation measures, it is calculated that the cost of reducing noise annoyance varies from EUR 16 to EUR 4200 per person per year. The findings clearly show that noise reduction at source (quieter vehicles) is much more cost-effective than treating noise at the receiver.
Full Paper
The danish national road noise strategy
Pedersen, Frank (1), Kristensen, Brian (1)
(1) EPA, Denmark
ABSTRACT
The Danish National Road Noise Strategy (2003) incorporates ten initiatives to reinforce the road authorities' efforts to reduce noise. The strategy address the annoyance and health impacts of traffic noise taking into account efficiency and costs of the noise mitigation measures. The socio-economic analysis of the initiatives shows that there are good opportunities to organize efforts providing economic surpluses. As nine out of ten dwellings affected by noise are situated adjacent to municipal roads, the strategy emphasizes helping the municipalities in their efforts to reduce noise. Nevertheless most of the initiatives to control noise problems before and after 2003 have been carried out along the national roads. As a follow-up to the strategy, a 'recipe book' for financial noise partnerships between municipalities and homeowners has been developed, so that this form of co-financing can become more widespread. In spite of the efforts of the government and the municipalities to reduce the road traffic noise, the latest evaluation of the strategy (2010) concludes that: The health effects are unchanged and the number of dwellings exposed to noise is not reduced. This emphasizes the importance of continued efforts to implement the strategy combined with the strategic EU noise mapping and action plans.
Full Paper
The Swiss way to silent roads
Walker, Urs
Federal Office for the Environment, Switzerland
ABSTRACT
The objective of Switzerland's noise abatement policy is to protect the health of the population and create a high quality of life. In a society in which space for housing development is scarce and there is constant population and traffic growth, as well as increasing individualization, this is a major challenge.
The latest calculations on noise pollution in Switzerland show that during daytime one in five persons, and at night one in six persons, are still exposed to harmful or disturbing road traffic noise. The associated decline of property values and health impacts generate massive costs. A study on long-term megatrends illustrates that the volume of traffic will continue to increase. Therefore forward-looking measures need to be taken today in order to prevent adverse health effects and preserve quietness as a significant location factor for housing, business and recreation. To achieve this goal, it will be essential to focus on measures that eliminate noise directly at source such as the use of low-noise tires and low-noise road surfaces, the lowering of speed limits and optimized driving behavior.
Full Paper
Performance of time domain and time-frequency domain adaptive beamformers with moving sound sources
Bao, Chaoying
DSTO, Australia
ABSTRACT
The need to extract a single audio signal of interest from a multi-source and noisy environment is common across many disciplines. Adaptive beamforming, due to its superior interference rejection and noise suppression, is a preferred processing technique for obtaining high quality audio in noisy environments. In a previous study, we have examined the performance of two classes of adaptive beamforming, namely, time domain and time-frequency domain adaptive beamforming, under the conditions that the sound sources were stationary and the signal model was accurate. In this paper, we extend the study to the situations where the sources are moving and certain amount of signal mismatch is allowed. Four different types of adaptive beamformers are considered. The robust Capon beamformer is used for time-frequency domain beamforming. The tapped delay line (TDL) structure is adopted for time domain adaptive beamforming. Three different adaptive algorithms are used for obtaining the optimal TDL filters. These are the sample matrix inversion method, the recursive least squares method with sliding window, and the block constrained least mean square method with diagonal loading. In the paper, the performances of those four adaptive beamformers are evaluated in terms of fidelity of the beamformer output, robustness of the system, and the computational complexity of the algorithm. It has been found that the robust Capon beamformer provides better performance than the time domain beamformers.
Full Paper
Application of the virtual time-reversal technique to transient sources localization in complex immersed struc
Leissing, Thomas (1), Audoly, Christian (1), Guyader, Jean-Louis (2), Guyader, Guillaume (2), Buisson, Quentin (2), Morange, Jean-Louis (3)
(1) DCNS Research, France
(2) SONORHC, France
(3) DCNS, France
ABSTRACT
Transient sonar detection systems have been developed over the last decades, and hence transient noise emissions from ship have become a matter of concern for acoustic discretion. One step towards the mitigation of transient noise emissions from ships consists in the accurate localization and identification of the noise sources. We use in this paper the virtual time-reversal method to localize vibratory transient noise sources. The localization system is implemented and tested in a representative naval structure. The test structure considered here is a semi-cylindrical ribbed shell partially immersed in water, equipped with some machinery items (pumps, engines, etc.). Due to the size of the structure and its complexity, the virtual model is constructed using point to point transfer function measurements. This transfer function database is then used to reemit reversed signal and to identify the transient source location. Various experiments are performed to demonstrate and analyze the performances of the localization system with both vibratory and acoustic excitations. The robustness of the method towards various parameters such as the measurement points meshing and the frequency band considered is detailed.
Full Paper
Advanced signal processing methods for the analysis of transient radiated noise from submarines
Leissing, Thomas (1), Audoly, Christian (1), Lachambre, Hélène (2), Stempfel, Guillaume (2)
(1) DCNS Research, France
(2) Genesis, France
ABSTRACT
Acoustic discretion is a key performance for many naval vessels such as submarines, in order to prevent underwater detection by adverse sonar systems. In the past decades, acoustic discretion of submarines has been greatly improved, as far as stationary noise is concerned. With the development of new sonar systems, with a capability to detect transient noises, it is now important to treat transient radiated noise as well. As an example, events such as the maneuver of a periscope mast can produce transient underwater noise, in the form of sequence of shocks and other type of noise. The first step toward the evaluation of the risk associated with a transient noise emission is the characterization of these signals. In that context, DCNS has tested some advanced signal processing tools from Genesis: LEA (Logiciel d'Expertise Acoustique), with its new Xtract module dedicated to the automatic separation of the different signal components. Some tests have been performed on signal samples. Several examples involving manual signal edition, automatic denoising and automatic separation of transient and tonal components of a signal are presented. For example, it can be shown that the suppression of background noise allows a better assessment of the spectral analysis of the signal of interest. Moreover, the different signal components, e.g. shocks and tonal components can be separated and treated separately. It is shown that the tools provide a very powerful chain for the treatment of complex signals. Eventually, the use of these tools will allow a better understanding of the transient underwater noise phenomena, allowing defining noise mitigation solutions.
Full Paper
Cross correlation matched field localization for unknown emitted signal waveform using two-hydrophone
Yao, Shuai (1), Li, Kun (1), Fang, Shiliang (1)
(1) 1Southeast University, Nanjing, China
ABSTRACT
Source localization is a crucial issue in underwater acoustics. Traditional matched field processing (MFP) use large vertical arrays to locate an underwater acoustic target. However, the use of the large arrays not only increases equipment and computational cost but also some problems such as element failures and array title degrades the localization performance. In this paper, the matched field localization method of using two-hydrophone is proposed for underwater acoustic pulse signals with unknown emitted signal waveform. Firstly, using the received signal of hydrophones and the ocean channel which can be calculated from an acoustic propagation model, the emitted signal for every grid location over search region can be estimated by using the least squares solution in the time domain. And then, the estimated signal is convolved with the ocean channel pulse for various trial source locations to generate the replica signal. Finally, matched field localization of using two-hydrophone for underwater acoustic pulse signals of unknown emitted signal can be estimated by comparing the difference between the cross correlation of the received signal and the cross correlation of the replica signal to construct the localization error function yielding the ambiguity surface of localization function. Theoretical analysis and numerical simulation demonstrate the effectiveness of the proposed matched field localization and the localization performance were analyzed under different signal to noise ratio (SNR) cases by simulation trial.
Full Paper
Combined effects of low frequency vertical vibration and noise on whole-body vibration sensation
Hiroshi, Matsuda (1), Nobuo, Machida (1)
(1) Nihon University, Japan
ABSTRACT
The operators of vehicles and construction work machines experience a variety of vibration and noise stimulation from the surrounding environment. It has been reported that vibration and sound stimuli, such as vibration music therapy and background music, have the psychological and physiological effects of mitigating tiredness and tension. The purpose of this study is to determine the effect of musical sound and noise on whole-body vibration sensation such as changes in sensation strength or uncomfortable sensation of vibrations. We studied low frequency vertical vibration generated in vibration environments including vehicles. We hypothesized that uncomfortable sensation of vibration could be reduced by adding sound to the vibration environment and comforting musical sounds to the sound stimulation. The vibration sensation when the subjects were simultaneously exposed to vibration and sound stimulation was measured by using a psychological method. From the experimental results, it was found that the vibration sensation strength has a maximum at a vibration frequency of 8 Hz. Also, the tendency of the vibration sensation to increase and decrease in response to the uncomfortable sensation of vibration was different with musical sound and noise.
Full Paper
Vibration properties of hand-arm system while holding a grip
Kuwada, Masashi (1), Yoshimura, Takuya (1), Tsurumi, Yasuaki (2), Yamada, Daisuke (2)
(1) Tokyo Metropolitan University, Japan
(2) Toyota Central R&D Labs
ABSTRACT
Recently, many vibration tools such as concrete breakers are used in the construction site. Workers holding them may suffer from vibration disorder such as white finger. They also feel uncomfortable from them. Many studies of vibration disorder have been carried out. However, there have been few studies for evaluating the comfort. Furthermore, dynamic properties of hand-arm vibration system by vibration exposure have not been reported. Thus, the purpose of this study is to investigate the vibration properties of hand-arm system when holding a grip. In this study, a motion capture system is used to measure the responses of the hand-arm; markers are attached to the subject's arm while holding a grip. The vibration is transmitted through the grip, and the transmissibilities of hand-arm system are measured. We investigate the vibration properties of hand-arm system by conducting curve fit to the measured FRFs. The subject's seated postures and the direction of the grip are changed to see the difference and common characteristics depending on these factors. In the result, we extract four natural modes of hand-arm system. The dependencies of vibration properties to the subject's conditions are also clarified.
Full Paper
Assessment of noise-induced annoyance by tones in noise from building mechanical systems
Lee, Joonhee (1), Wang, Lily M (1)
(1) University of Nebraska-Lincoln, USA
ABSTRACT
Prominent tones in noise generated by mechanical equipment in buildings can cause complaints from occupants in buildings. The ISO 1996-2 and ANSI S1.13 standards describe methodologies and metrics to quantify tonality perception, but the influence of tones in noise on human annoyance and performance is not fully understood yet. This paper investigates annoyance responses of humans while exposed to background noise with tonal components. Twenty participants completed digit span tasks while exposed to noise signals with differing levels of tones and overall loudness. Subjects were also asked to rate their annoyance after completing tasks under each noise signal. The subjective testing was carried out in the indoor acoustic testing chamber at the University of Nebraska. A dose-response model is investigated to predict the upper limits of acceptability for tonalness using assorted noise metrics.
Full Paper
Effects of room acoustics on comprehension of foreign-accented speech by native and non-native English-speaking listeners
Peng, Zhao (1), Hanna, Kristin E (1), Boyd, Brenna N (1), Wang, Lily M (1)
(1) University of Nebraska-Lincoln, USA
ABSTRACT
In a previous study by the authors, reverberation time (RT) and background noise level (BNL) were both found to have negative effects on native and non-native English-speaking listeners in comprehending English speech produced by native American-English-speaking talkers. Comprehension scores were adjusted for listeners' baseline English proficiency levels. In the present study, instead of native English-speaking talkers, two native Mandarin Chinese talkers (one male, one female) with similar English spoken proficiency were recruited to produce the same speech materials used in the previous study. A similar methodology was adopted to conduct speech comprehension tests on three groups of listeners: 1) native American-English, 2) native Mandarin Chinese and 3) other non-native English. The listeners' performance on foreign-accented speech comprehension is investigated under 15 acoustic conditions, created from five levels of RT (0.4 to 1.2 seconds) and three levels of BNL (RC-30, 40 and 50). Does a talker having a foreign accent change the results amongst the different listener groups in comprehending English speech under adverse acoustic conditions? Comparisons are made with the previous study, which showed that the negative impacts of RT and BNL varied between native and non-native listener groups.
Full Paper
Curve Squeal: Causes, Treatments and Results
Hanson, David (1), Jiang, Jiandong (1), Dowdell, Bruce (1), Dwight, Richard (2)
(1) Transport for New South Wales, Australia
(2) University of Wollongong, Australia
ABSTRACT
Curve squeal is a major impact from rail operations on tight curves through residential areas. TfNSW has embarked on an intensive study into curve squeal and this paper presents an overview of that study. We have taken a holistic approach by considering each of the key contributors to wheel squeal: rolling stock, the wheel/rail interface, and the trackform. This paper will report on the results of trials, measurements and research into each of these areas, including (1) measurement and analysis methods for identifying/classifying curve squeal. This includes how squeal is identified from wayside noise measurements, a means of determining which wheel is squealing and which wheel/rail contact area is involved. (2) Which rolling stock is causing squeal and why. This includes a discussion of wagon steering behaviour based on measurements from wayside systems, the difference in performance between wagon classes and designs, and what this means for squeal noise generation. (3) Management of the wheel/rail interface for mitigating curve squeal. This includes a discussion of the importance of rail profile and friction management and provides results from on-track testing.
Full Paper
Bearing defect size estimation for extended raceway defects
Petersen, Dick (1), Howard, Carl (1)
(1) University of Adelaide, Australia
ABSTRACT
A method is presented for estimating the size of bearing raceway defects that are larger than the angular spacing between balls. Previous defect size estimation techniques cannot be used for such defects since they are limited to defects that are smaller than the ball angular spacing. The reason for this is that two defects that differ in size by the ball angular spacing produce the same time difference between the defect entrance and exit events in the vibration response, and it is this time difference that is used to estimate the defect size in previous techniques. Thus, to distinguish between such defects, a third feature of the vibration response is required. It is hypothesised and validated through simulations that the third distinguishing feature is the characteristic frequencies of the low frequency event. This event occurs when a ball gradually de- and restresses upon entering and exiting the defect and corresponds to a varying stiffness excitation of the rigid body modes of the bearing assembly. It is shown that two defects that differ in size by the ball angular spacing produce different rigid body modes because such defects generate different bearing stiffness variations. This results in low frequency events with different characteristic frequencies since these frequencies correspond to the natural frequencies of the rigid body modes that are excited as balls enter and exit the defect.
Full Paper
Acoustic rail grinding - measures of long term effectiveness: Epping to Chatswood Rail Link case study
Vegh, Serge (1), Kochanowski, Radek (2), Croft, Briony (3)
(1) Transport for NSW, Australia
(2) Sydney Trains, Australia
(3) SLR Consulting, Australia
ABSTRACT
The Epping to Chatswood Rail Link (ECRL) commenced operation in February 2009 with approximately 11.1 million gross tonnes of electric multiple unit rolling stock using each of the two tunnels annually. However, during acceptance testing of the ECRL an in-car noise issue was identified which required a reduction of approximately 12 dB. An acoustic rail grinding strategy was then developed and implemented. Grinding on the Sydney rail network has typically been conducted at passby speeds of 10 km/h that leave a longitudinal signature on the rail head with a wavelength of approximately 40 mm, and this in turn leads to tonal noise at approximately 450 Hz. In comparison, the ECRL grinding strategy saw higher speed grinding passbys of 25-30 km/h, with finer stones. This shifted the wavelength of the grinding signature to approximately 100-150 mm and reduced the tonal peaks in the roughness spectrum. This strategy contributed 3 to 4 dB of the overall noise reduction in a cost and time effective manner allowing the ECRL to commence revenue operations. This paper assesses the sustainability and maintainability of this acoustic grinding strategy, and compares the roughness of the freshly ground track to the roughness after approximately five and a half years of operation (shortly before the next scheduled rail grind).
Full Paper
Comparison of Kilde and NORD2000 rail noise prediction methodologies
De Lisle, Simon (1), Burgemeister, Kym (1)
(1) Arup Acoustics, Australia
ABSTRACT
In Australia, predictions of rail noise are most commonly conducted using the Kilde Rep 130 methodology, which has been twice superseded. The most recent version of the Nordic methodology is NORD2000. This paper compares the practical results of the Kilde and NORD2000 methodologies in a range of simple scenarios which have been selected to isolate specific effects, such as source directivity, meteorological effects, shielding losses and reflections. A test case representing complex real-world conditions has also been studied. Significant differences have been observed in the results of the two methodologies, with NORD2000 generally predicting larger propagation losses. Determining which methodology provides more accurate predictions would require comprehensive measurements in tightly controlled conditions. However, it appears that Kilde uses a more conservative approach, to provide 'margin for error' due to its simplistic calculations.
Full Paper
A simplified approach for evaluating noise impact from high-speed lines
Zhang, Xuetao
SP Technical Research Institute of Sweden, Sweden
ABSTRACT
Sweden is now considering new railway lines typically adapted to high speeds up to 320 km/h. Noise impact from high-speed lines and noise mitigation measures where required becomes urgent to be investigated. As the current calculation model for railway noise used in Sweden is not applicable for the purpose, the Swedish Transport Administration decides to prepare a new noise assessment method for high-speed lines. This new noise assessment method is not necessary to be comprehensive because noise evaluation along high-speed lines is mainly oriented.In this paper a simplified source module is described. The simplification has three folds of meanings: (1) only dominant noise sources, rolling noise and aerodynamic noise, are considered; (2) a classification of train types is made based on noise emission strength, not on the physical parameters; (3) the effect of noise measures (such as rail/wheel dampers, sleeper pads or mats, wheel skirts, etc.) is integrated into a single parameter, additional noise reduction (given either in total level or in spectrum). Moreover, the effect of noise barriers along a high-speed line is left to be handled by the sound propagation module.
Full Paper
Development of a new loudness model in consideration of audio-visual interaction
Aizawa, Kai (1), Kamogawa, Takashi (2), Arimitsu, Akihiko (2), Toi, Takeshi (2)
(1) Graduate school of Chuo University, Japan
(2) Chuo University, Japan
ABSTRACT
Recently, several researchers have been focusing on loudness perception of sound sources when the sounds are presented with the appearance of what radiates them. They concluded the visual information may increase/decrease the perceived loudness intensity. However, because these works concentrated mostly on subjective evaluation of actual sounds, there is a demand for an objective loudness model in consideration of the audio-visual interaction. Due to this reason, this paper focuses on its development. First of all, a new equal loudness curve considering the color effect is proposed for a limited frequency band based on experimental results of audio-visual stimuli consisting of sinusoidal sounds and color patches. Secondly, this function is applied to the loudness calculation to correct the effect of colors, whereas, the other computation processes are the same as a conventional loudness model of ISO532B. This is because it is considered that the mechanism of sound perception is not affected by colors but by our ear structures. Finally, several audio-visual stimuli are evaluated and the result is compared to result analyzed by the new loudness model using the corresponding conditions and the model accuracy is discussed.
Full Paper
Noise evaluation based on loudness-perception characteristics of older adults
Kurakata, Kenji (1), Mizunami, Tazu (1)
(1) AIST, Japan
ABSTRACT
The frequency-weighting A used for noise measurement was determined based on hearing characteristics expressed as equal-loudness-level contours. The time-averaged, A-weighted sound level (LAeq) of a sound corresponds well with the perceived loudness. However, good correspondence between LAeq and the perceived loudness is confined to cases in which listeners are young people with normal hearing. This study used a psychoacoustic experiment to investigate loudness of various sounds perceived by older people aged over 60. Analyses of results revealed that sound levels weighted by listeners' hearing characteristics matched the judged loudness better than LAeq values did. This report describes the development of a noise evaluation method that can evaluate noises for senior citizens more accurately than the conventional method using A-weighting.
Full Paper
Loudness Using a Threshold Correction Factor
Novak, Colin (1), Ule, Helen (2), Gaspar, Robert (1)
(1) University of Windsor, Canada
(2) Akoustik Engineering Limited, Canada
ABSTRACT
Experimental studies have shown that for short gaps (2 to 5 ms) loudness and threshold are higher than for uninterrupted noise. Other studies have also shown that the present integration models for loudness do not adequately account for short duration phenomena. Studies have instead shown that the multiple look approach is the applicable method for these short-term circumstances. However, present technologies (i.e. FFT) are not adequate to deal with short duration sounds across the entire frequency spectra. A compromised approach is taken here to account for the threshold phenomena in the presence of gaps while using an integration model. This approach is referred to as a threshold correction factor.
Full Paper
Measurement of attention to auditory signal in noisy environment
Sato, Hiroshi
National Institute of Advanced Industrial Science and Technology, Japan
ABSTRACT
When people find or localize a target sound in noisy environment, he/she employ his/her attention to the sound. If we can measure degree of attentions to a sound in daily life situation, the results can be used to control and/or design sound environment as well as auditory sign. However, it is difficult to measure auditory attention especially in real life situation. The intention of this study is to develop a tool to be used in real public space for evaluating performance of acoustic guide signal to present target directions. The challenge of this study is to measure the degree of attention to a sound with gaze measurement and presenting the relation between S/N and gazing detection.
Full Paper
Improvements in calculating the loudness of time varying sounds
Sottek, Roland
HEAD acoustics GmbH, Germany
ABSTRACT
Recently, a new ISO standard for loudness of arbitrary sounds ISO 532-1 (1) was proposed for the revision of ISO 532:1975 section 2 (method B) (2). It is based on DIN 45631/A1:2010 (3), which includes the widely used standard DIN 45631:1991 (4) for stationary sounds as a special case. ISO 532-1 eliminates uncertainties of existing standards by strictly defining the complete procedure of loudness calculation starting with the waveform of the time signal and ending with specific and total loudness vs. time functions.
The strict definition of the complete procedure is a step forward to comparability of calculated loudness results, and fully conforms to DIN 45631/A1:2010 for the sake of continuity.However, although the results of this algorithm are in accordance with the results of many listening tests, there are still phenomena that are not covered by this method. For example, the calculated loudness of sweep signals shows fluctuations, whereas the perceived loudness does not. This is due to the implemented filter bank based on fixed, contiguous third-octave filters. As a possible solution a loudness calculation method is presented that is based on a hearing model (Sottek) using an aurally adequate filter bank of highly-overlapping asymmetric filters (5). In addition, the nonlinearity between specific loudness and sound pressure has been reconsidered in this model according to results of many listening tests (6).
Full Paper
Thermophones using carbon nanotubes and alternative nanostructures for high power sound generation and noise cancellation
Aliev, Ali E
University of Texas at Dallas, USA
ABSTRACT
There is a large promise for thermophones in high power sonar arrays, flexible loudspeakers and noise cancellation devices. The freestanding aerogel-like carbon nanotube sheet as a thermoacoustic (TA) heat source demonstrates so far the best performance. However, the limited accessibility of large size free standing carbon nanotube sheets and other even more exotic materials published recently, hampers the field. I present here new alternative materials for TA heat source with high energy conversion efficiency, additional functionalities, environmentally friendly and cost effective production technologies. I discuss the TA performance of alternative nanoscale materials and compare their spectral and power dependencies of sound pressure in air. The study presented here focuses on engineering of thermal gradients in the vicinity of nanostructures and subsequent heat dissipation processes from the interior of encapsulated thermoacoustic projectors. Applications of TA projectors for high power SONAR arrays, sound cancellation, and optimal thermal design, regarding enhanced energy conversion efficiency, are discussed.
Full Paper
Acoustic absorption behaviour of carbon nanotube arrays
Ayub, Md (1), Zander, Anthony C (1), Howard, Carl (1), Cazzolato, Benjamin S (1), Shanov, Vesselin N (2), Alvarez, Noe T (2), Huang, David M (3)
(1) School of Mechanical Engineering, University of Adelaide, Australia
(2) Department of Biomedical, Chemical and Environmental Engineering, University of Cincinnati, Cincinnati, OH 45221, USA
(3) School of Chemistry and Physics, University of Adelaide, Australia
ABSTRACT
Advances in nanotechnology have provided acoustic researchers with a number of new materials with nano-fibres and nano-pores that can potentially be implemented as an acoustic porous absorber. This paper investigates the acoustic absorption behaviour of carbon nanotube (CNT) arrays, in order to quantify the acoustic characteristics and absorption performance of nanoscopic fibres in comparison with conventional porous materials. Tests were conducted using an impedance tube to measure the normal incidence acoustic absorption coefficient of vertically aligned carbon nanotube (CNT) arrays. Results show that a forest of 3 mm CNT arrays can provide as much as 10% acoustic absorption capability within the frequency range 125 Hz - 4 kHz. It was found that CNT arrays, in some cases, may provide better acoustic absorption than conventional porous materials of equivalent thickness and mass. The outcomes of this investigation highlight the potential of nanoscopic fibres for use as light-weight acoustic absorbers.
Full Paper
Improving sound absorption bandwidth of micro-perforated panel by adding porous materials
Li, Dengke (1), Chang, Daoqing (1), Liu, Bilong (1), Tian, Jing (1)
(1) Key Laboratory of Noise and Vibration Research, Institute of Acoustics, Chinese Academy of Sciences, 100190, Beijing, P.R.China
ABSTRACT
Micro-perforated panel (MPP) has been widely used in acoustic treatments due to its wideband sound absorption coefficient. When the MPP is applied to absorb low frequency noise, more space is required, while at the same time sound absorption bandwidth becomes narrow. In this paper, a combined absorption structure containing the MPP, airspace and porous materials is proposed to improve the sound absorption bandwidth of MPP. The absorption coefficients of combined absorption structures were calculated and as well were measured in the impedance tube. The measured and predicted results are well agreed in the frequency of interest. When the porous materials are put in front of the MPP and there is an air layer between them, the sound absorption is much better in comparison with that of the porous materials are located behind the MPP.
Full Paper
Wind turbine noise measurements - How are results influenced by different methods of deriving wind speed?
Broneske, Sylvia
Hayes McKenzie Partnership, UK
ABSTRACT
With the increasing number of operational wind farms/turbines, the requirement for noise measurements required to demonstrate compliance with planning conditions is increasing as well. The British ETSU-R-97 noise limits are often set relative to measured or standardised 10 m height wind speeds and therefore the assessment of noise from wind turbines requires simultaneous noise and wind speed/direction measurements. For financial reasons, smaller and single turbine sites are often not equipped with a meteorological mast. If no independent hub height wind measurements are available, wind speed is either taken from nacelle anemometers or derived from power measurements combined with the power curve for the respective wind turbine type. Noise measurements referenced to nacelle anemometer data will be compared with the same measurements but correlated with derived power curve wind speed, and measured wind data from separate met mast or other remote sensing devices. The influence of incorrect filtering of wind data for shadow effects (mast and/or nearby wind turbines) on the noise assessment may be presented, depending on how much time is available. The advantages and disadvantages of the various methods will be discussed.
Full Paper
Wind turbine sound - metric and guidelines
Larsson, Conny (1), Öhlund, Olof (1)
(1) Uppsala University, Sweden
ABSTRACT
The meteorological conditions vary over the globe but also change over the day and the year and vary a lot depending on the terrain for a certain location. The meteorological parameters govern both the wind turbine emission sound levels and the sound propagation conditions and therefore gives rise to different sound immission levels. Long-time measurements of meteorological effects on sound propagation from wind turbines over forest areas have been performed at two sites in Sweden for more than two years. One site is located in the southern part with flat terrain and the other site is located in the northern part of Sweden with more hilly terrain. The aim of the project is to improve the knowledge of sound propagation from wind turbines and especially over varying terrain and weather conditions. Control measurements of wind turbine immission sound levels will be needed to see that they fulfill the noise regulations. It is therefore of most importance to be able to make representative measurements. Discussions about under what meteorological conditions the immission measurements have to be carried out, the sound metric and the impact of the guidelines are presented in this paper.
Full Paper
Correlation of amplitude modulation to inflow characteristics
Madsen, Helge Aagaard (1), Bertagnolio, Franck (1), Fischer, Andreas (1), Bak, Christian (1)
(1) Technical University of Denmark, Denmark
ABSTRACT
Amplitude modulation (AM) of noise from wind turbines and its more extreme version named "other amplitude modulation" OAM have been investigated intensively during the last few years due to the additional annoyance impact this type of noise has compared to broad band noise. In a recent published research by RenewableUK the hypothesis has been that one of the causes of OAM is transient stall on the blade due to non uniform inflow such as shear. Part of the RenewableUK research work was a contribution by DTU on analysis of data from the DANAERO MW experiment from 2009. In the DANAERO experiment a new 38.8m test blade for a 2MW NM80 turbine was manufactured and equipped with a massive instrumentation comprising flush mounted surface microphones, pressure taps and five hole pitot tubes. The correlation of the spectra from the surface microphones and the measured inflow angle (IA) confirmed the strong increase in the noise source for high IA. As only few 10min data sets were measured in the DANAERO project a data set with measured inflow angle from 2003 on the same turbine has been used to explore the statistical properties of AM and OAM based on assumed correlation to IA.
Full Paper
An investigation of Different Secondary Noise Wind Screen Designs for Wind Turbine Noise Applications
Novak, Colin (1), Sjöström, Anders (2), Ule, Helen (3), Bard, Delphine (2), Sandberg, Göran (2)
(1) University of Windsor, Canada
(2) Lund University, Sweden
(3) Akoustik Engineering Limited, Canada
ABSTRACT
The use of diaphragm type microphones with the typical foam windscreen ball for outdoor noise measurement applications are mostly restricted to wind speeds below 4 to 6 m/s. This is due to the extra noise induced into the microphone, particularly at low and infrasonic frequencies, as a result of the wind excitation on the diaphragm. For wind turbine noise measurement applications, it is often necessary to measure the turbine noise under the typical operating conditions with wind speeds up to 12 m/s. This introduces a problem in the measurement system, as the normal microphone setup and windscreen are not adequate at these elevated wind speeds. Secondary windscreens, such as for example that prescribed by IEC 64100-11, "Acoustic noise measurement techniques" imparts their own problems including ridged body motion of the windscreen structure due to turbulence. Also, ground plane secondary windscreen measures the noise at ground level, instead of at ear level. This study investigates the use of several secondary windscreens with microphones capable of measuring at infrasonic frequencies for measuring wind turbine noise at elevated wind speeds. The result was that no windscreen provided a full solution to the problem. Specific recommendations for additional windscreen design and investigation are included.
Full Paper
COSMA - A European Approach on Aircraft Noise Annoyance Research
Bauer, Michael (1), Collin, Dominique (2), Iemma, Umberto (3), Janssens, Karl (4), Márki, Ferenc (5), Müller, Uwe (6)
(1) Airbus Group Innovations, Germany
(2) SNECMA SA, France
(3) Universita Degli Studi ROMA TRE, Italy
(4) LMS International N.V., Belgium
(5) Budapesti Muszaki es Gazdasagtudomanyi Egyetem, Hungary
(6) Institute for Aerospace Medicine, Germany
ABSTRACT
COSMA - Community Orientated Solutions to Minimize Aircraft Noise Annoyance - was a European approach within the 7th Framework Programme of the European Commission.Aircraft noise engineering is focused more or less on the reduction of the noise emission for single aircraft components, and separately treating the noise abatement procedures during take-off and landing. COSMA's aim was to combine both under the aspect of noise annoyance: To develop basic engineering criteria for an annoyance friendly aircraft design and managing flight operation routines in order to reduce the noise related annoyance within airport communities. The project had to create the link between the aircraft/sound engineering domain, and the noise effects domain. To achieve this goal, extensive field studies around European airports, combined with psychometric studies in laboratories have built the basis for describing the optimal aircraft sound characteristics which anticipates a lower annoyance. Specific sound synthesis methods, combined with the optimization of procedures for flight operations were used to create low noise annoyance practices, including future aircraft concepts.The authors give an overview about the final status of the project's achievements in the major project areas: Annoyance related examinations, sound engineering, and optimization.
Full Paper
Multi-objective optimization of takeoff and landing procedures: level abatement vs quality improvement of aircraft noise
Iemma, Umberto (1), Burghignoli, Lorenzo (1), Centracchio, Francesco (1), Galluzzi, Valerio (1)
(1) Roma Tre University, Italy
ABSTRACT
The present paper deals with an original multi-objective optimization approach to the mitigation of the acoustic impact of commercial aircraft. The method is based on the coupling of the classical noise level reduction approach and an innovative sound-quality assessment method, developed during the EC-funded projects SEFA (Sound Engineering For Aircraft, FP6, 2004-2007) and COSMA (Community Noise Solutions to Minimise aircraft noise Annoyance, FP7, 2009-2012). Indeed, the increase of air traffic and the rapid expansion of urban areas around airports are making the aviation community noise a key aspect of the sustainable development of the transportation system. As a consequence, the scientific and industrial research community is focusing the attention on the development of innovative aircraft configurations, aimed at a substantial reduction of the acoustic impact of aircraft. Unfortunately, such a new concepts will be ready for operation only in the long-term, thus making extremely urgent the identification of alternative strategies to mitigate the impact on the residential community. The present work addresses the problem by integrating into the multi-objective, multi-disciplinary optimization framework developed and validated in COSMA, the sound-matching criterion developed within SEFA, with a noise-level based indicator minimization. Specifically, the two merit factors to be minimized are the norm of the difference between the noise produced by the configuration under analysis and a target sound, and the EPNL (effective perceived noise level) at a certification point. The target sounds are obtained by synthesis, using sound engineering techniques aimed at the sound quality improvement, on the basis of the results of the psychometric tests campaigns performed in SEFA and COSMA. The simultaneous reduction of the two objective functions is achieved through a multi-objective optimization problem adopting global evolution methods, as implemented within the MDO environment FRIDA (FRamework for Innovative Design in Aeronautics). Results will be presented for procedure optimization in terms of Pareto fronts, for two types of aircraft in both take off and landing conditions.
Full Paper
IDEALVENT: Characterization of installation effects in aircraft Environmental Control Systems
Schram, Christophe (1), Kucukcoskun, Korcan (1), Christophe, Julien (1), Van De Wyer, Nicolas (1)
(1) von Karman Institute for Fluid Dynamics, Belgium
ABSTRACT
Environmental Control System (ECS) are used in order to provide equipment cooling and good thermal comfort for passengers in commercial aircrafts. They are also responsible for significant acoustic annoyance affecting both passengers in the cabin and personnel servicing the aircraft on the ramp. The IDEALVENT project is tackling these issues by proposing a combination of detailed experimental work and advanced simulation techniques to better model, predict and mitigate ECS noise. A specific focus is placed on installation effects, which are addressed through a modular experimental rig permitting various combinations between a blower unit, downstream obstacles and upstream inflow distortions. The preliminary results of the project have permitted highlighting the importance and nature of the aerodynamic and acoustic installation effects that occur in such configurations. This paper is focused on acoustic measurements that have been performed using in-duct microphone arrays. These arrays have been designed to decompose the active and passive components of the blower scattering matrix into a modal basis including up to the first radial mode of the duct.
Full Paper
NINHA: Noise Impact of aircraft with Novel engine configurations in mid- to High Altitude operations
Van Oosten, Nico (1), Collin, Dominique (2)
(1) Anotec Engineering, Spain
(2) Snecma, France
ABSTRACT
The potential introduction of aircraft fitted with advanced counter-rotating open rotor (CROR) engine power plants should contribute significantly to the reduction of fuel burn and gaseous emissions. In the 1980s, prototypes of the first generation of open rotor engines were developed and tested. One of the findings was that the noise generated by these engines, even in the en-route flight phase, could be considered significant, thus hazarding public acceptance. Since then significant effort has been dedicated to improving the CROR aero-acoustic design; the new generation of CROR engines currently envisaged will be much quieter than its predecessors.
Full Paper
Control of noise from public entertainment activities in Hong Kong
Kwok, Kwun Ting (1), Cheng, Kin Wui (1)
(1) Environmental Protection Department, Hong Kong
ABSTRACT
Hong Kong is a vibrant and hyper-dense metropolitan city with over 7 million people being housed in a total area of around 1,100 square kilometers. In such a dynamic city, there is a huge demand of entertainment venues from the community for various kinds of entertainment. Due to the land sparsity, availability of appropriate venues is limited. Outdoor places for other uses, such as stadiums, parks, promenades and streets etc., are frequently used for holding public entertainment events, in particular, during various festivals. However, these open-air places are usually located in close proximity to residential premises. Noise from frequent public entertainment activities had aroused great concern from local residents. This paper describes the current framework and noise control criteria adopted in Hong Kong for controlling noise from open-air public entertainment activities with a view to striking a balance between the quest for quieter environment and the community's aspiration for enjoyment of public entertainment activities.
Full Paper
New techniques to determine specific noise for increasing the effectiveness of continuous unattended noise monitoring systems
Manvell, Douglas (1), Stollery, Phil (2)
(1) Brüel & Kjaer Sound & Vibration A/S, Denmark
(2) Brüel & Kjaer Sound & Vibration A/S, UK
ABSTRACT
Continuous, unattended noise monitoring systems can immediately alert you should noise levels exceed defined criteria. Once alerted to an exceedance, operators can act to return levels to compliance. This approach has two significant limitations. Firstly the operator can only take action after the breach has occurred and therefore systems are only able to inform owners about problems that have occurred in the past, rather than allowing them to maintain compliance. Secondly the noise limit exceedances might not be due to specific noise from the operator but from unrelated, residual noise in the often complex noise climates around the site. Compliance breaches are frequently triggered by aircraft overflights, road traffic or community sources. Modern monitoring systems enable users to view noise characteristics and listen to the noise breach to determine the source and take action if it is relevant. However, this approach can create significant false positives each taking up operator time to address. This paper describes how airport noise management systems have addressed this problem by combining data from other systems. It also shows how different techniques are required in urban & industrial noise management, giving examples of techniques that allow operators to take action before a compliance breach occurs.
Full Paper
Live music and the \'agent of change\' principle
McArdle, Sean (1), Lee, Gillian (2), Hui, Elizabeth (2)
(1) Rigby Cooke Lawyers, Australia
(2) Marshall Day Acoustics, Australia
ABSTRACT
The gentrification of Melbourne's inner suburbs since the late 90s has resulted in increasing tension between inner city residential development and well-established music venues. Fuelled by strong community support for live music, the Victorian government recently announced a suite of reforms to implement the 'agent of change' principle to protect live music venues from residential encroachment. In advance of pending law reform activities, this paper examines the key issues relevant to development of noise policy to complement the agent of change principle. The paper describes the current regulatory framework in Victoria for music noise, identifies risks associated with potential policy approaches and provides high level discussion concerning stakeholder viewpoints as relevant to the issue.
Full Paper
Continuous noise monitoring network design: an end user perspective
Sparke, Clayton James
Advitech Pty Ltd., Australia
ABSTRACT
Continuous Noise Monitoring (CNM) systems are commonly utilised to assist in the remote assessment of noise impacts associated with industrial complexes. In Australia, these systems have benefited significantly from rapid innovation in technology and wireless communication networks in the last 20 years, and now collect vast quantities of data that may be used in near real time or stored for later processing. In some sectors, the speed of this innovation and rapid uptake of new technology has outpaced the development of training and education tools that adequately equip end users with the ability to transform this data into useful information. A survey of Environmental and Community managers was undertaken to explore how CNM Systems are used to assist in the management of environmental noise impacts in the NSW mining sector. The survey sought to understand the various objectives of continuous noise monitoring, identify constraints and opportunities, and provide for self-assessment of end user competencies. The outcomes of this study contribute to narrowing of the knowledge gap between users and suppliers of environmental management technology, and furnish stakeholders with information to improve the utility of CNM Networks.
Full Paper
Residential acoustic amenity in \'vibrant\' mixed use areas
Wheatley, Glenn Robert
Renzo Tonin & Associates, Australia
ABSTRACT
The 'compact city' is a focus of many sustainable urban development models around the world. With higher density mixed-use development a central element, developments that were previously separated to reduce potential conflict (such as from noise) are now being brought closer together. This research investigated noise impacts between commercial and residential uses, in the context of New South Wales (NSW) planning policy, where fine-grain and vibrant mixed-use development is promoted. A single site case study, which included resident and business operator surveys, was used to gather information on expectations and experiences with regard to noise impact. The case study was supplemented by a policy and academic literature review. The results of the research suggest that NSW planning policy does not adequately address the expectations of residents and business operators in mixed-use areas regarding noise impact, or the objectives of their strategic planning policies concerning the creation of vibrant mixed-use sites. It is concluded that strategic planning objectives for the promotion of vibrant/active mixed-use areas, particularly those with late night trading premises, should only be set if suitable design responses are available, as the development of incompatible uses may ultimately restrict development or reduce the quality of life for inhabitants in urban areas.
Full Paper
Study on aero-acoustic structural interactions in fan-ducted system
Chiang, Yan Kei (1), Choy, Yat Sze (1), Cheng, Li (1), Tang, Shiu Keung (1)
(1) Hong Kong Polytechnic University, Hong Kong
ABSTRACT
Mitigation of sound radiation from subsonic axial fan in the fan-ducted system at low frequencies remains a technical challenge. Traditional dissipative approach such as absorption material often requires sufficiently long attenuation path for desirable noise reduction performance. More advanced passive control technology such as membrane housing which relies on vibro-acoustic coupling mechanism works effectively on the attenuation of the first and second blade passage frequency in case of steady flow. However, the performance of such device which is composed of thin membrane may be affected by unsteady flow field. This study examined the interaction between vortex unsteady motion, a tensioned membrane housing of finite length and axial fan with dipole nature using the matched asymptotic expansion technique and potential theory. A two-dimensional numerical model is established to explore the sound radiation of each components and the performance of the membrane housing for controlling sound radiation from axial fan in the present of vortex inside uniform mean flow. The results show that there is higher chance of sound amplification when a vortex stream is closer to the light membrane under weak mean flow speed. Under the condition of weak mean flow speed, the sound radiation from the membrane is also amplified when the cavity height is shallower. The result is beneficial for the design of the device of membrane housing.
Full Paper
Transfer-matrix-based approach for an eigenvalue problem of a coupled rectangular cavity
Iwamoto, Hiroyuki (1), Tanaka, Nobuo (2)
(1) Seikei University, Japan
(2) Tokyo Metropolitan University, Japan
ABSTRACT
This study concerns an eigenvalue problem of a vibro-acoustic coupling system. In the conventional method, the dynamics of a vibro-acoustic coupling system is calculated with modal coupling methodology which uses eigenfunctions of a rigid-walled cavity. Therefore, particle velocity on the surface of a panel is always calculated as zero, while it should be coincident with the velocity of the panel. To overcome the problem, this paper presents a new methodology for deriving accurate eigen-pairs of a vibro-acoustic coupling system. First, a transfer matrix is introduced which can describe the characteristics of the sound field. This is followed by the derivation of the sound pressure on the coupled rectangular panel. Then, the vibrational velocity of the panel is derived with the sound pressure being used as the input. Furthermore, the eigenvalue problem is formulated based on the equations of vibration and sound field. Finally, the numerical simulation is carried out, demonstrating the validity of the proposed method.
Full Paper
Modal contributions to the acoustic responses of fluid-loaded shells
Qu, Yegao (1), Hua, Hongxing (1), Peters, Herwig (2), Kessissoglou, Nicole (2)
(1) Shanghai Jiao Tong University, China
(2) UNSW Australia, Australia
ABSTRACT
This work compares results from analytical and numerical techniques to predict the modal contributions to the radiated sound power and far-field sound pressure for structures submerged in a heavy fluid medium. A fluid-loaded cylindrical shell with hemispherical end caps is examined. The cylinder is excited by either axial or transverse forces acting at one end, to predominantly excite the lowest order cylinder circumferential modes. A modified variational method combined with a spectral boundary element method is used to develop an analytical model of the coupled hemispherical and cylindrical shells under heavy fluid loading conditions. The displacement components and the sound pressure are expanded in the form of a double mixed series using Fourier series and Chebyshev orthogonal polynomials. A fully coupled finite element/boundary element model of the same coupled hemispherical-cylindrical shell is also developed. A numerical technique for modal decomposition of the acoustic responses of the structure using the fluid-loaded structural modes is implemented. The individual contributions of the cylinder circumferential modes to the sound power and directivity of the radiated sound pressure are observed. The techniques presented here provide greater physical insight into structure-borne radiated noise from fluid-loaded shells.
Full Paper
Sound transmission between rooms coupled through partition with elastically restrained edges
Zhang, Yufei (1), Du, Jingtao (1), Liu, Yang (1), Yang, Tiejun (1), Liu, Zhigang (1)
(1) Harbin Engineering University, China
ABSTRACT
Sound transmission between rooms is often encountered for the acoustic design and noise control engineers. A clear understanding on the acoustical behavior of rectangular cavities connected by flexible panel structure can be of the fundamental significance. In this paper, sound transmission between rooms through the flexible partition with its edges elastically restrained is investigated. Both the translational and rotational springs are assumed along each panel edge to simulate the structural boundary conditions. The energy variational formulations in conjunction with Rayleigh-Ritz procedure are employed for this structural-acoustic coupling system modeling with the improved Fourier series constructed as the admissible functions, in which the supplementary terms are introduced to overcome potential discontinuities associated with the spatial derivatives of the conventional Fourier series on the panel-cavity interface as well as the panel elastic edge supports. Numerical examples are then presented to demonstrate the reliability and effectiveness of the current model through the comparison with the predicted data obtained by Finite Element Analysis using NASTRAN. Effect of the position and boundary restraining condition of flexible partition on the sound transmission characteristics of coupled rooms is analyzed in detail. Finally, some useful and interesting findings from this work are given in the conclusion section.
Full Paper
A shape classification for the acoustic radiator using its sound field
Kim, Koo-Hwan (1), Kim, Yang-Hann (1)
(1) KAIST, South Korea
ABSTRACT
A method for classifying the shapes of sound radiator is presented. It assumes that sound field can be measured by a linear array. A sound field, due to the radiator vibrating with uniform velocity, can be determined by its shape, size, and orientations. Measured data also can be varying from the array's position. To classify the shape of radiators from these measured data, sound field data has to be converted into a measurement positions invariant feature. We show that the directivity factor has these invariability and it can categorize the unknown shape of radiator according to several pre-defined candidate shape. In this paper, suggested method is applied to classify the several regular polygons.
Full Paper
A moving sound source localization method based on TDOA
Miao, Feng (1), Yang, Diange (1), Wang, Rujia (1), Wen, Junjie (1), Wang, Ziteng (1), Lian, Xiaomin (1)
(1) Tsinghua University, China
ABSTRACT
The Time Difference of Arrival (TDOA) method has been widely used for sound source localization. However, because of the Doppler-effect, the TDOA method cannot be directly used for locating moving sound sources. This paper develops a moving sound source localization method based on TDOA, combining with Doppler-effect elimination and source plane scanning. This method is suitable for locating sound sources moving in a plane, with a measurable velocity. In this method, the sound source plane is meshed into grids. Choose one grid point as the assumed sound source location, eliminate the Doppler-effect from the measured sound pressure signals, and then locate the sound source using TDOA method. The deviation between the localization result and the chosen grid point is recorded. Do this progress by scanning all the grids on the plane. The grid point which minimizes the deviation through the plane is taken as the sound source location estimation. Simulations show that this method can accurately locate high speed sound sources even with background noise, using short sections of signals received by a four-microphone array.
Full Paper
Withdrawn8
Withdrawn8,
ABSTRACT
Withdrawn8
High-resolution nearfield acoustic holography based on iterative weighted equivalent source method
Xu, Liang (1), Bi, Chuan-Xing (1), Zhang, Xiao-Zheng (1), Zheng, Chang-jun (1)
(1) Hefei University of Technology, China
ABSTRACT
Because of the ill-posed nature of equivalent source method (ESM)-based nearfield acoustic holography (NAH), regularization methods based on the minimum L2-norm criterion such as the Tikhonov regularization are usually employed to stabilize its reconstruction procedure. However, the minimum L2-norm constraint sometimes makes the reconstruction result too smooth and thus degrades the spatial resolution of NAH, because this kind of constraint tends to disperse the acoustic field energy on the hologram surface to all the equivalent sources. To deal with this problem, an iterative weighted ESM (IWESM) is proposed, in which an iterative weighted regularization procedure is developed to solve the strengths of equivalent sources. The IWESM can reduce the dispersion of acoustic field energy on the hologram surface to those equivalent sources that contribute little to the acoustic field, and get more reasonable solution of source strengths. The validity of the IWESM is proven by a numerical simulation, and the result shows that comparing with ESM-based NAH, the proposed method can significantly improve the spatial resolution of reconstruction results.
Full Paper
Laboratory data examining impact and airborne sound attenuation in heavy timber loft style construction.
Byrick, Wilson Robert
Pliteq Inc., Canada
ABSTRACT
An increasingly popular trend in urban neighborhoods is to convert old factory or industrial spaces into "loft" style condominiums. The structure in these old factory spaces tends to be comprised of heavy timber floor-ceiling systems. A floor-ceiling system, representative of what is found in the field, was constructed in the laboratory to complete impact insulation and airborne sound testing in accordance with ASTM E492 and ASTM E90 respectively. The baseline assembly was constructed of 300mm x 300mm (12"x12") wood beams spaced 100 mm (48" OC), 57mm x 133 mm (nom 3"x6") wood planks, and 19 mm x 149 mm (nom 1"x6") wood planks laid perpendicular to the layer below. No ceiling was used, as part of the commercial desire for this type of space is the exposed wood ceiling. The baseline assembly tested to IIC 24 and STC 29.Various floor toppings were tested and the resulting IIC and STC data is presented in the paper.
Full Paper
Challenges for acoustic calculation models in \"Silent Timber Build\", Part 2
Kouyoumji, Jean-Luc (1), Bard, Delphine Gérard (2), Borello, Gérard (3), Guigou, Catherine (4)
(1) FCBA, France
(2) Lund university, Sweden
(3) InterAC, France
(4) CSTB, France
ABSTRACT
The project "Silent Timber Build" will develop new prediction tools for timber structures. There are several challenges that have to be overcome to provide a full prediction tool. The differences in weight, stiffness and density for wooden structures compared to traditional, heavy and more homogeneous structural material have repercussions on how the sound propagates throughout the structures, affecting the sound and vibration insulation performance and also theories to be used in prediction models. The project will use Finite element simulations (FEM) and Statistical Energy Analysis (SEA) approaches to predict acoustical behavior of light weight timber constructions. This article, following another article Part 1, will focus on medium and high frequency range calculations. Statistical methods will be used in the medium and high frequency, where the acoustic performance of wooden building components (walls and floors) is generally limited by the presence of structural links and couplings. Statistical Energy Analysis (SEA) has proven to be an efficient approach, providing robust vibroacoustic models in this frequency region. The extension of statistical methods towards the low frequencies has to be evaluated, especially regarding time responses of impact noise on floor systems. For full-scale building, Virtual SEA method will be used as well as analytic SEA approach in frequencies low enough in order to optimize the overlap to FEM.
Full Paper
Laboratory facilities for sound transmission measurements - validation by measurement and simulation methods
Meissnitzer, Marlon (1), Buchegger, Blasius (1), Ferk, Heinz (1)
(1) TU Graz, Austria
ABSTRACT
Test facilities for sound transmission measurements have to be designed according specific international standards. The experience, e.g. of past round robin tests showed, that in spite of the specifications within these standards some differences in the sound transmission measurement occur within different facilities. Some of these differences are related to possible varieties of the room configuration, others may be caused by different mounting conditions of the test specimens, but there are also some effects that are not fully investigated and descripted within these standards. This paper deals with the validation of such test facilities by measurement and simulation. The combination of these techniques can be helpful to find the right measures for a good diffusity, avoid unwanted resonances and find the right places for diffusors, microphone and loudspeaker positions in a virtual way before realization. Thus, a step by step validation, combining simulation and measurement can help to get the necessary knowledge for a qualified room and equipment design, as it is shown by an example.
Full Paper
Effects of sample construction, sample size and niche depth on measured sound transmission loss
Wareing, Robin R (1), Davy, John Laurence (2), Pearse, John R (1)
(1) University of Canterbury, UK
(2) RMIT University, Australia
ABSTRACT
Sound transmission loss measurements, performed using a small test facility (1.5 m2 sample size) are compared with results from full wall sample (11.6 m2). The effects of sample construction, sample size and niche depth are investigated. Significant changes in the measured sound transmission losses were observed between the samples measured. The variation between the two sample sizes was found to be heavily influenced by the construction of the sample. The variation between the sizes was further confounded by the niches present in both sample arrangements. Individually the contributing factors could be explained using existing theories but the interaction of the different factors was more difficult to predict. The behaviours observed were investigated, including the variations in the pressure at the surface of each panel and the pressure variations throughout the room. The pressure variations within the room were not a major contributor to the variations in transmission loss, whereas the variations across the surface had a small effect on the transmission loss. Finally the appropriateness of using the small transmission loss rig for comparative testing of samples was evaluated. The small test rig was found to be useful for tests in which the construction of the test sample was consistent.
Full Paper
The uncertainty in sound insulation of an industrially prefabricated lightweight timber construction
Öqvist, Rikard
Tyréns AB, Sweden
ABSTRACT
The variations in sound insulation are often large for lightweight constructions. A large number of measurements is therefore necessary to reliably evaluate the acoustical properties of a lightweight construction. The Swedish company Lindbäcks Bygg has since the '90s developed a timber system based on industrially prefabricated volumes. This paper presents a statistical evaluation of all measurements of impact and airborne sound insulation made on the system between 2011 and 2014. The objective was to quantify the variations in impact and airborne sound insulation in both weighted terms and 1/3 octave bands, and investigate the relationship between workmanship and acoustical properties. The study consists of a large number of vertical measurements between nominally identical room pairs. The measurements were grouped according to date, room size, floor level and assembly team. The variations were larger for impact than for airborne sound insulation. The impact sound level was higher in large rooms, which may have been caused by the method of joining several volumes. The sound insulation was somewhat better on higher floors. No significant differences could be identified between the different assembly teams. To improve the system, the impact sound insulation should be in focus.
Full Paper
Digital sound system modelling and design
Davis, Lauren (1), Mackenzie, Neil (1)
(1) Aurecon, Australia
ABSTRACT
As part of a staged redevelopment of the Adelaide Convention Centre, a new Plenary Hall is to be constructed with a capacity of 3150 seats. The Hall can be subdivided and includes an operable theatre in the round within each sub-division. This paper outlines the acoustic performance criteria for the complex operation modes of the Plenary Hall. It provides a review of the sound system design philosophy and electro-acoustic modelling technique used to predict the acoustic performance of the sound system. It also provides an outline of evolving networking technologies used to provide a flexible digital audio network using a standard data network infrastructure.
Full Paper
The prediction of the complex characteristic acoustic impedance of porous materials
Larner, David James (1), Davy, John Laurence (1)
(1) RMIT University, Australia
ABSTRACT
Modeling the complex characteristic acoustic impedance and complex wavenumber of porous materials allows the prediction of the complex specific acoustic impedance of a system consisting of porous absorbers and air cavities in front of a rigid surface. By using the transfer matrix method, the complex characteristic acoustic impedance and complex wavenumber of a porous material can be predicted by using the measured complex specific acoustic impedance of two different systems of the porous material and an air cavity, performed in a two-microphone impedance tube. Depending on the method, the material can be measured with either a rigidly terminated back plate at the back of the material, or a rigidly terminated air cavity at the back. This paper looks at why predictions using the single and double thickness method break down for thinner, less dense materials.
Full Paper
An explicit time-domain finite-element method for room acoustics simulation
Okuzono, Takeshi (1), Otsuru, Toru (2), Sakagami, Kimihiro (1)
(1) Kobe University, Japan
(2) Oita University, Japan
ABSTRACT
The time-domain finite-element method (TD-FEM) is a reliable numerical method for room acoustics sim- ulation. With the recent progress in computer technology, the use of FEM at high frequencies has become a realistic option. However, efficient simulation at high frequencies is still cited as a challenging task. One of the key to realize such simulation is to reduce the discretization error called dispersion error. In this paper, the applicability of an explicit TD-FEM with a dispersion reduction technique called modified integration rule on room acoustics simulation at high frequencies is tested. First, an explicit scheme with frequency-independent impedance boundary condition is derived for addressing boundaries with finite impedance. Then, the accu- racy and efficiency of the explicit TD-FEM is demonstrated in comparison with an implicit TD-FEM for sound field analysis inside a cubic cavity with rigid boundaries at the frequencies up to 8 kHz. Finally, the accuracy of the explicit TD-FEM is examined for sound field analyses with finite impedance boundaries. Results showed that the explicit method offered the same accurate results as the implicit method with less computational time, whereas the implicit method was more efficient in term of memory requirement.
Full Paper
A BEM study of the influence of musicians on onstage sound field measures in auditoria
Panton, Lilyan (1), Holloway, Damien (1)
(1) University of Tasmania, Australia
ABSTRACT
Many recent studies have sought to assess the acoustical experience of musicians playing in ensembles through development of acoustic measures undertaken on stage in auditoria. It is generally proposed that such measures be undertaken in the presence of stage furniture to better replicate the real conditions onstage with an ensemble present. However, conditions are arguably not necessarily realistic because furniture is customarily removed within 2m radii of the source and receiver to avoid disturbing reflections, and because it is seldom practical to make the measurements with the musicians present. Furthermore, consistency of conditions is also potentially an issue. This paper uses BEM (boundary element method), validated against published full and model scale data, to investigate the differences between sound fields on a stage with an orchestra present and on a bare stage. Sensitivity to perturbations of the stage configuration is also investigated. The results of this study show that for a chamber orchestra, set up on stage, for 250 Hz and above the sound field on an occupied stage differs significantly from an empty stage.
Full Paper
Evaluation of the acoustic performance of a theatrical space set up in a restored Latomia in Ragusa Iblea
Patania, Francesco (1), Gagliano, Antonio (1), Nocera, Francesco (1), Cicero, Andrea (1)
(1) University of Catania, Italy
ABSTRACT
Sicily has many artistic and architectural treasures, wonderful historical buildings, monasteries, abbeys and convents that are often restored and used as government buildings, university buildings, theatre and collective spaces for exhibitions. They often have elliptic or irregular shapes and characteristic values of absorption and diffusivity coefficient of wall surfaces that cause serious acoustical problems such as standing waves, flutter echo, sound focusing and intensive late reflections (greater than 100 ms). Moreover, long and flat parallel walls cause undesirable flutter echo which decreases speech intelligibility seriously and diminishes the effectiveness of early arriving sound energy. The paper presents the results of an acoustic study on outstanding Latomia of Gonfalone located in Ragusa Iblea that was restored and is used as marvelous theatrical space. Firstly, the Authors carried out an acoustic measurement campaign to evaluate the main acoustic indices and parameters and set the current acoustic quality. After that, they applied acoustic computer simulations on the Latomia in order to compare the measured data coming from the survey measurements and the data coming from the code. In this way, it has been possible to test the reliability and accuracy of the code and to evaluate on the spatial distribution patterns of speech intelligibility and other acoustic indices defined in ISO 3382. Finally, they have determined the suitable interventions of acoustic correction to improve the acoustic quality of the theatrical space.
Full Paper
Soundscape Transects: Case Studies from New York City and O\'ahu
Carter, J Parkman
Rensselaer Polytechnic Institute, USA
ABSTRACT
A new method of linking both the aural and visual conditions of a soundscape is used to create transect maps across complex sonic environments. Two case study transects from New York City will be demonstrated: one comparing highway noise penetration in two adjacent but very different northern Manhattan parks, and the other spanning the width of the island of Manhattan at 75th Street encompassing the Hudson Riverfront park, the Upper West Side neighborhood, Central Park, the Upper East Side neighborhood, and the East River walkway. Another series of soundscape transect case studies from Hawaii's island of O'ahu demonstrates the impact of traffic noise at elevations ranging from sea level to over 800 meters (2,700 feet) high, captured along a variety of ridges across the island. In all of these case studies, having the directional audio information embedded in the extensive photographic field provides salient representations of the specific characteristics of the soundscapes under study.
Full Paper
Towards a quantitative tool to assess the soundscape
Welch, David (1), Shepherd, Daniel (2), Dirks, Kim N (1), Tan, Mei Yen (1)
(1) University of Auckland, New Zealand
(2) Auckland University of Technology, New Zealand
ABSTRACT
The aim was to develop a quantitative questionnaire that could easily be administered to assess people's perceptions of the current Soundscape. In a preliminary phase, a group of people identifying themselves as good writers were recruited and played recordings of natural, traffic, and human Soundscapes. As these were playing, participants were asked to write their impressions and responses to each for approximately twenty minutes. Qualitative analysis was used to extract themes from the writing. These themes were identified by key words and scalar (6-point) items were developed to form a short, 19-item questionnaire. This was then administered to 228 people in Auckland city centre, New Zealand. Respondents were able to use the questionnaire, and analyses showed that the items were not independent of each other. Factor analysis revealed patterns of responding, and comparisons between people reporting different levels of Noise Sensitivity and Noise Annoyance revealed that these were associated with the perception of the Soundscape as measured by our questionnaire. The questionnaire appears to be a useful tool, and further research will improve upon it.
Full Paper
Measuring a Soundscape of the captive Southern White Rhinoceros (Ceratotherium simum simum)
Wiseman, Susan (1), Wilson, Preston S (2), Sepulveda, Frank (3)
(1) Texas State University-San Marcos, USA
(2) University of Texas at Austin, USA
(3) Baylor University, USA
ABSTRACT
Many creatures, including the myopic rhinoceros, depend upon hearing and smell to determine their environment. Nature is dominated by biophonic and geophonic sounds quickly absorbed by soil and vegetation. Anthrophonic urban soundscapes exhibit vastly different physical and semantic characteristics: reflections from hard geometric surfaces, multi-path propagation and reverberation, and often increased sound pressure levels compared to nature, in addition to much anthropogenic noise not found in nature. Noise damages humans physiologically, including reproductively, and likely damages other mammals. Rhinos vocalize sonically and infrasonically but audiograms are unavailable. They generally breed poorly in urban zoos, where infrasonic noise tends to be chronic. Biological and social factors have been studied but little attention if any has been paid to soundscape. To comprehensively describe the rhinos' acoustic environment at Fossil Rim Wildlife Center, one of the few U.S. facilities to successfully breed white rhinos in recent years, its broadband sound metrics were studied throughout a week of normal park activities. Further analysis will seek particular parameters known to be injurious to humans, plus those already known to invoke response in animals. Later, a variety of other facilities could be recorded to seek correlations between their soundscapes and the health and well-being of the creatures within their care.
Full Paper
Outcome based optimisation of road traffic noise mitigation
Kean, Simon
NSW Roads and Maritime Services, Australia
ABSTRACT
New South Wales, Australia has shifted to an outcomes based approach to delivering traffic noise solutions with mandatory principles that must be met. Supporting procedures give guidance to achieving the principles most of the time. Key tasks in meeting desired outcomes are to identify appropriate noise criteria and to design an equitable mix of 'at-source' and 'at-receiver' road traffic noise mitigation. Particular attention has been given to noise barrier optimisation. This paper presents how legacy approaches have been revised to address recent criteria changes and a shift to outcomes based policy. In New South Wales road traffic noise criteria are set by the State Environmental Protection Authority based on how the road functions in a network. These criteria are guidelines rather than mandatory legislation. Road construction proponents such as the State's Roads and Maritime Services are required to meet these criteria where reasonable and feasible. This is in recognition that it may not always be reasonable to mitigate barely perceivable changes in noise level.
Full Paper
Buffer distances for surface roads and elevated highways correlated with pre-existing ambient noise
Zhang, Jiping (1), Buret, Marc (2), Wu, Shuoxian (3), Zhao, Yuezhe (3), Shen, Saiyan (1), Zhang, Xin (1)
(1) Zhejiang Research & Design Institute of Environmental Protection, China
(2) VicRoads, Australia
(3) South China University of Technology , China
ABSTRACT
The guidelines for environmental impact assessment (EIA) in China prescribe a buffer zone - consisting in reserved land or compatible uses -on both sides of noisy roads. However, many EIA reports typically only include predictions and assessment of the traffic noise levels due to the concerned road only. The pre-existing ambient environmental noise levels are then overlooked which may result in under-estimating the resulting noise levels and in buffer distances that are too short. Moreover, in the specific case of viaducts or elevated roads, consideration should be given to extend the concept in the vertical direction as well as the horizontal direction. Based on 3D mathematical modeling by means of proprietary software and typical input traffic data, several road situations are assessed and discussed here. These include surface urban road (e.g. arterial and access roads) and elevated highways passing through different land uses with specific pre-existing noise environments. These examples are used to determine and review the distribution of buffer zones and their boundaries. Results from this review can apply to EIA for road projects and their optimization.
Full Paper
Planar laser induced fluorescence imaging of bubble formation
Fedrizzi, Marcus (1), Soria, Julio (2)
(1) Monash University, Australia
(2) Monash University, Australia; King Abdulaziz University, Saudi Arabia
ABSTRACT
A slowly forming underwater gas bubble will grow, form a neck and detach when the neck collapses, emitting a pulse of sound. During the late stage of the neck collapse the acoustic pulse displays a rarefaction and the acoustic compression begins shortly after detachment. This compression appears to coincide with the formation of an internal jet inside the bubble and an understanding of the behaviour of the bubble internal jet is sought in order to understand the origin of the acoustic emission. In this study time resolved high speed imaging of the bubble detachment process has been undertaken using planar laser induced fluorescence (PLIF) illumination. From these images the internal jet development and evolution are investigated as well as the effect of the jet on the instantaneous bubble volume. The link between the internal jet and the surface waves on the bubble is also investigated for insight on their contribution to bubble sound emission.
Full Paper
Interaction of a pair of horizontally aligned bubbles in gravity field
Jiao, Han (1), Shi, Dongyan (1), Wang, Zhikai (1), Li, Hongqun (1)
(1) Harbin Engineering University, China
ABSTRACT
Both large deformation and strong discontinuity problems exist in the process of bubble-bubble interaction. The lattice Boltzmann method which is based on the microscopic level has naturally comparative advantage to describe tiny changes in multiphase flow system. A three-dimensional lattice Boltzmann (LB) model of two horizontally aligned bubbles is presented to explore the bubble movement, topological transformation and bubbles interaction characteristics. In this model, the viscous effect is easily considered, and surface tension effect is realized by introducing a discrete LB body force term. To provide a reference, the isolated bubble dynamics driven by gravity is simulated firstly, and the surface tension effect is studied. Then the effect of gap distance and interface width on the coalescence of two stable bubbles is discussed. Finally, the interaction of two horizontal bubbles with different size ratio in gravity field is explored carefully. The results not only show the detailed coupling and coalescence process of two rising bubbles, but expose that the relative size ratio plays an important role in the interaction. The opposite phenomenon can be seen. When bubbles are of different size, the coalescence phenomenon will happen, but when they are in the same size, the rejection phenomenon will replace it.
Full Paper
Acoustic imaging of surface ship wakes
Kouzoubov, Alexei (1), Wood, Shane (1), Ellem, Richard (1)
(1) DSTO, Australia
ABSTRACT
Techniques for three-dimensional visualization of a surface ship bubbly wake using a high-frequency narrow beam profiling sonar are reported. Instrumentation, experimental set-up, and data processing are described. An Imagenex profiling sonar is mounted on the side of a boat at about 1 m below the water surface. The narrow pencil beam scans the water through the sectors whose plane is perpendicular to the direction of the boat motion. Two scanning techniques were used. In the first, the wake is scanned from the side with about 50° sectors, with the profiling boat moving slowly along the wake in the direction opposite to that of wake laying ship. In the second technique the boat moves inside the wake and scans it with a 180° sector. Both techniques have their advantages and disadvantages which are discussed in the paper. The GPS coordinates of the profiling boat and angular position of the sonar head are recorded. These data allow building a three-dimensional image of the bubbly wake during post-processing.
Full Paper
Application of lattice Boltzmann method to research bubble interacting with spherical particle
Shi, Dongyan (1), Wang, Zhikai (1), Zhang, Aman (1)
(1) Harbin Engineering University, China
ABSTRACT
During the process of bubbles interacting with particles, the bubble movement velocity, jetting phenomenon, topological deformation, and even properties of flow field may demonstrate novel variation. To investigate these characteristics, the lattice Boltzmann method (LBM) which is based on kinetic theory is adopted to build up the three dimensional coupled model. The gas-liquid interface with large density ratio is described with free-energy based lattice Boltzmann multiphase model, and the fluid-structure boundary is implemented in the form combining LBM and finite difference method (FDM). Except the obvious and traditional phenomenon such as large interface deformation and velocity variation, it has been found that the gravity-driven spherical bubble finally become a bubble ring after the coupling process. Combining the intrinsically microscopic property of LBM, the complex coupling process is researched with deeper study on relative size and fluid properties. The results may not only advance the LBM application in multiphase coupling field, but make a significant insight into the micro-transient phenomena of bubbles interacting with particles.
Full Paper
Road traffic noise, air pollution and cardio-respiratory health in European cohorts: a harmonised approach in the BioSHaRE project
Blangiardo, Marta (1), Cai, Samuel (1), De Hoogh, Kees (1), Gulliver, John (1), Morley, David (1), Doiron, Dany (2), Elliott, Paul (1), Hansell, Anna (1), Hodgson, Susan (1)
(1) Imperial College London, UK
(2) McGill University and Genome Quebec Innovation Centre, Canada
ABSTRACT
Background and aims: Few studies have investigated joint effects of road traffic noise and air pollution on cardiovascular outcomes. This project aims to quantify the joint and separate effects of both exposures on prevalent and incident cardiovascular disease and asthma as part of the EU-funded BioSHaRE project involving five European cohorts (EPIC-Oxford, EPIC-Turin, HUNT, Lifelines, UK Biobank).
Methods: Health outcomes have been ascertained by self-report (prevalence) and medical record (incidence) and retrospectively harmonised across the five cohorts. Residential road traffic noise exposures for each participant are being estimated using a European noise model based on Common Noise Assessment Methods in Europe (CNOSSOS-EU). Cross-sectional epidemiological analyses are in progress, virtually pooled using DataSHIELD methods.
Results: In total, 716,945 men and women are included, mostly >40 years. Initial analysis of EPIC-Oxford and Lifelines showed prevalence of self-reported hypertension to be 26%, high blood lipids 15% and asthma 11% and mean annual 24-hour noise estimates of 56.4 dB(A) (EPIC-Oxford) and 65.8 dB(A) (Lifelines). Correlations between noise estimates and NO2 are generally low (r~0.1 to 0.4).
Conclusions: Pooling of individual level harmonised data from established cohorts offers the large sample sizes needed to investigate effects of road traffic noise and ambient air pollution on cardio-respiratory diseases.
Full Paper
Transferability of the results from laboratory basic research on cognitive impairment by background sound to real life offices
Liebl, Andreas (1), Kittel, Maria (1)
(1) Fraunhofer Institute for Building Physics, Germany
ABSTRACT
The Irrelevant Sound Effect (ISE) is considered to be of great practical importance to real-life work tasks, like in open-plan offices. The knowledge about the physical parameters determining the ISE has also been implemented in national and international standards determining the physical set values for the acoustic design of open-plan offices. However, it may be questioned whether this phenomenon, which stems from basic research in cognitive psychology, can easily be generalized to office environments. Simplifications and means of control applied to laboratory experiments guarantee for reliability and internal validity of the experimental results. However, external validity may be questioned. Details of the real life environment must be properly considered. This paper focusses on the relevance of specific sound conditions. Results are reported which address the relevance of the number, gender and location of speakers for the ISE to arise.
Full Paper
Prediction of virtual sound source elevation improved by including input source spectral shape in the prediction equation
Manor, Ella (1), Martens, William Leigh (1)
(1) University of Sydney, Australia
ABSTRACT
Presented with familiar broadband sound sources, human listeners are expected to base reports of source elevation primarily upon spectral variation due to directional dependence of the head-related transfer function (HRTF). Using four recorded speech sounds as sources, this study tested whether reported elevation of virtual sound sources might be systematically influenced by the spectral shape variation that naturally occurs in human speech. A set of 36 virtual sound stimuli were created by processing those four sound sources with nine binaural HRTFs collected at angles spaced at 10-degree intervals on the frontal plane, ranging from 40 degrees below the horizontal plane to 40 degrees above. Perceived source elevation was reported via a graphical user interface by each of five listeners who showed substantial individual differences in response distribution. Overall the collected reports were not highly correlated with the angles at which HRTFs had been measured; however, after the perceptual data were adjusted by subtracting from each source elevation report the overall mean elevation reported by each listener, these centred elevation angles were well predicted by a regression equation that included two terms. The first term was the elevation angle at which the binaural HRTFs were measured, while the second term captured source spectral bandwidth variations between the four sound sources processed using the nine HRTFs.
Full Paper
Study on elevated light rail induced vibration attenuation along the surrounding ground
Liu, Changqing (1), Zhou, Yude (1), Tu, Ying (1), Xu, Weimin (1)
(1) Shanghai Academy of Environmental Sciences, China
ABSTRACT
In this paper, the elevated light rail induced vibration attenuation along its surrounding ground is studied. A finite element vibration analysis model is established to compute the vibration response of the surrounding ground with different soil conditions, and the effects of soil parameters on the ground surface on vibration attenuation is analyzed. Vibration measurements were conducted at the surrounding ground of elevated light rail with different soil conditions, which verified the feasibility of FEA (finite element analysis). By the combination of FEA and vibration measurement results, a fast prediction method of the ground vibration is put forward. It is concluded that soil parameters have great effect on the attenuation of ground vibration and environmental vibration caused by the elevated rail could be predicted through finite element method. The conclusion is meaningful to the control and prediction of environmental vibration around the elevated light rail.
Full Paper
Force Density Measurements at Sound Transit
Nelson, James (1), Watry, Derek (1), Faner, Patrick (1), Lamb, Isabelle (2), Reed, Tracy (3), Wright, Armin (4)
(1) Wilson, Ihrig & Associates, USA
(2) Jacobs Associates, USA
(3) Sound Transit, USA
(4) USA
ABSTRACT
The environmental assessment of ground vibration caused by rail transportation systems is becoming more detailed as new transit and commuter rail systems approach or encroach on sensitive manufacturing and laboratory research activities. Methods for measuring low frequency vehicle/track forces were developed to improve predictions of vibration in Seattle and identify appropriate vibration control strategies. These methods expand on the methodology of ground vibration prediction used by the U.S. Federal Transit Administration, based on the concept of force density level and line source response. Vehicle/track force density measurements were conducted in tunnels using sinusoidal excitation and statistical tests of significance to improved estimates. The methods were used to overcome the low vibration response of the tunnel structure at low frequencies in over-consolidated soils. The vibration data indicate the effect of track curvature, axle spacing, and profile grinding.
Full Paper
Experimental modal analysis of high-speed railway carriage
Ouyang, Shan (1), Sui, Fusheng (1)
(1) Key Laboratory of Noise and Vibration Research, Institute of Acoustics, Chinese Academy of Sciences, China
ABSTRACT
Experimental modal analysis of high-speed railway carriage Body in White (BIW) with 7 meters long is presented in this paper. The validity of modal testing is verified by comparing mode shapes of the entire carriage with that of beam structures assembled at the bottom floor. Results show that, the demarcation frequency between low frequency vibration and high frequency vibration is 100 Hz. As below 100 Hz, all 6 global modes are included; while above 100 Hz, the mode count within a 1/3 octave frequency bandwidth is higher than 5, which means it could be regarded as high frequency range in statistic energy analysis. Results of modal testing can be provided to modify the finite element model of the carriage structure.
Full Paper
Use of a "Hybrid" Empirical/Finite Element Approach for Predicting Groundborne Vibration from Rail Systems
Saurenman, Hugh (1), Roulo, Eric (2)
(1) ATS Consulting, USA
(2) Roulo Consulting, Inc., USA
ABSTRACT
The finite element method (FEM) is widely used in various engineering fields to model complex structures. Applying FEM to predict groundborne vibration from rail systems has been tested, but always has been limited by difficulty in characterizing soil properties. The empirical method developed in the 1980s (often referred to as the "FTA method") remains the standard approach used in North America to perform detailed predictions of groundborne vibration and to determine the need for vibration mitigation measures. The FTA method is based on in-situ vibration propagation tests and is almost always found to provide more accurate predictions than even the most complex computer models. This paper describes a "hybrid" approach that uses data from vibration propagation testing to refine input parameters for an FEM model. The basic steps are (1) perform a standard vibration propagation test, (2) develop an FEM model of the test configuration using estimated soil properties, (3) "tune" the properties of the FEM model to optimize the correlation with the test results, and (4) modify the FEM model to be a tunnel in place of a borehole. The accuracy of this hybrid approach and other approaches for using FEM models to improve predictions of groundborne vibration will be discussed.
Full Paper
A parametric study on the influence of track irregularities upon train induced ground vibration
Yokoyama, Hidefumi (1), Yashiro, Kazuyuki (2), Kato, Shinjiro (2), Ohta, Takehiro (1)
(1) Railway Technical Research Institute, Japan
(2) JR-Central Consultants, Japan
ABSTRACT
Track irregularity is an important factor of train induced ground vibration, and sometimes causes strong ground vibration. For example, track irregularity due to corrugated rail increased 16 to 31.5 Hz components of ground vibration more than ten decibels on a shallow freight train line tunnel. To estimate the influence of track irregularity, we performed a parametric study using a program for solving coupled vibration of moving-vehicle and structure. We at first confirmed the accuracy of the program by comparing measured and calculated vibration of an in-situ measurement site. In the parametric study, we calculated the acceleration of roadbed caused by sine wave form track irregularity with various wavelength and amplitude. As a result, track irregularity amplitude was found to have certain threshold value. If track irregularity amplitude is larger than the threshold, roadbed acceleration increases as the track irregularity amplitude increases. However, if track irregularity amplitude is smaller than the threshold, roadbed acceleration is almost independent to the amplitude of track irregularity. The threshold amplitude corresponds to the balance point of static axle load and inertial force excited by the track irregularity.
Full Paper
Reconstruction of sound fields with a spherical microphone array
Fernandez-Grande, Efren (1), Tim, Walton (1)
(1) DTU, Technical University of Denmark
ABSTRACT
Spherical microphone arrays are very well suited for sound field measurements in enclosures or interior spaces, and generally in acoustic environments where sound waves impinge on the array from multiple directions. Because of their directional properties, they make it possible to resolve sound waves traveling in any direction. In particular, rigid sphere microphone arrays are robust, and have the favorable property that the scattering introduced by the array can be compensated for - making the array virtually transparent. This study examines a recently proposed sound field reconstruction method based on a point source expansion, i.e. equivalent source method, using a rigid spherical array. The study examines the capability of the method to distinguish between sound waves arriving from different directions (i.e., as a sound field separation method). This is representative of the potential of the method to perform sound field identification and visualization in non-anechoic spaces, and ultimately for general in-situ measurements.
Full Paper
Non-stationary Holography on Arbitrary Source Shapes
Gomes, Jesper (1), Ishii, Yutaka (2), Ginn, Bernard (1)
(1) Brüel & Kjaer SVM, Denmark
(2) Brüel & Kjaer SVM, Japan
ABSTRACT
Laser scanning and accelerometer measurements are often used for analysing vibrations of for instance motors under operation. However, the methods have certain disadvantages: Laser techniques typically scan one point at a time, which limits the methods to be applied only for stationary conditions. Accelerometers can be used for non-stationary conditions, but their physical mounting will to some extend influence the vibration of the source surface and due to cabling they are not practical for rotating objects. Near-field Acoustical Holography (NAH) is a non-contact experimental technique for mapping sound and vibration, and since the sound field is measured at multiple points around the source simultaneously, it can also be applied for non-stationary conditions. In particular, the Equivalent Source Method (ESM) is an attractive holography method, because it does not require neither the source nor the array geometry to be given in separable coordinates (planar, spherical, cylindrical etc.). This paper describes a non-stationary ESM approach for reconstruction of quantities like surface velocity and displacement. A set of measurements has been made with a 60 channel microphone array on a small electrical motor. Vibrations were also measured with a laser vibrometer in order to validate the accuracy of the array calculations.
Full Paper
Exploring the limitations and expectations of sound source localization and visualization techniques.
Heilmann, Gunnar (1), Doebler, Dirk (2), Boeck, Magdalena (1)
(1) gfai tech, Germany
(2) GFAI e.eV. Germany
ABSTRACT
In the late 80's and early 90's institutions like NASA (USA), DLR (Germany), NLR (Netherlands) as well as companies like Boeing (USA) and Airbus (Europe) were leading the academic and technical development of sound source localizations techniques. As companies in today's globalized world operate under pressure of competition and governmental legislation, the visualization of sound sources was and is essential for understanding a product's acoustic behavior and therefore an integral part of product development. To make the world a quieter place, all try to improve it by understanding, reducing and controlling noise. Even 15 years after the initial market introduction of commercial Beamforming systems not everyone trusts and understands their capabilities and limitations. The aim of this paper is to present a variety of applications and results to show their possibilities and increase the understanding of the limits for different technologies for sound source localization and visualization methods. To do so, a vast selection of colorful and practical examples will provide a better understanding of what is feasible. The given examples range from small motors for digital cameras to household appliances, from cars to mining trucks, from small rooms to theatres and stadiums or from bats to elephants.
Full Paper
Detection and direction estimation of a sudden loud sound for the hearing assistive eyeglasses
Kim, Ki-Won (1), Choi, Jung-Woo (1), Kim, Yang-Hann (1)
(1) Korea Advanced Institute of Science and Technology, South Korea
ABSTRACT
An assistive device for the hearing-impaired is proposed to detect and visually display the direction of incidence when a sudden loud sound occurs out of sight. The result is intuitively presented in four angular regions, such as the front, back, left, right regions, through the three procedures; decision of the sound occurrence, reduction of reflections, and direction estimation. Basic concepts of the direction estimation is to use the four directional microphones steering toward corresponding angular regions, and each directional microphone is realized by the array signal processing based on the modified LCMV beamformer. The result is obtained by comparing the beamformer output levels, and leads our attention to corresponding region using LEDs only when a sudden loud sound is detected. The detection is performed using the change of the overall sound pressure level with respect to time as a feature, and its performance and latency are affected by the length of temporal integration. To keep the performance with short latency, an amplitude follower is applied.
Full Paper
Developing beam-forming devices to detect squeak and rattle sources by using FPGA
Kim, Youngkey (1), Kang, Jungoo (1), Lee, Myunghan (2)
(1) SM Instruments, Korea
(2) Hyundai Motors, Korea
ABSTRACT
Industry's high interest on squeak and rattle leads the development of a beam-forming device. Detecting squeak and rattle (SR) noise has been one of the best applications of the beam-forming devices. Localizing the SR noise sources is the most important step of the whole SR noise reduction efforts. In addition, the SR noise mainly consists of high frequency components and the beam-forming has better performance in high frequency range. Successful beam-forming devices for SR noises need to have fast data processing ability in order to detect transient behavior of the SR noise. The paper introduces how digital technologies are used to develop high speed beam-forming device. Since beam-forming process mainly consists of basic mathematical operation, such as addition, delay and multiplication, the process can be implemented in a Field Programmable Gate Array (FPGA) Chip. Because the FPGA has real-time MHz fixed loop rate, the processing loop rate is not the problem anymore. In this paper, two types of beam-forming devices developed by using FPGA are introduced. Application examples show the performance of the devices.
Full Paper
Active Snore Control System Integrated with Apnea Detector
Kuo, Sen M (1), Chang, Cheng-Yuan (1), Pottim, Karunakar (2), Liu, Lichuag (2)
(1) Chung Yuan Christian University.Taiwan
(2) Northern Illinois University. USA
ABSTRACT
This paper presents a snore active noise control (ANC) system to effectively reduce the loud snore for the snorer's bed partner. Real-time experiments are conducted to evaluate the noise reduction performance based on the headboard and pillow setups. This snore ANC system is integrated with a non-obtrusive technique to detect obstructive sleep apnea (OSA) of the snorer. The OSA detection is based on the bispectral analysis of the snore signals picked up by the reference microphone of ANC system.
Full Paper
Active flow control of the exhaust noise from internal combustion piston engine
Leclercq, Damien J J (1), Howard, Carl (1)
(1) University of Adelaide, Australia
ABSTRACT
The concept of reducing piston engine exhaust noise by controlling the flow through the exhaust line has been investigated theoretically and demonstrated experimentally in previous work. While this work demonstrated a successful application to a medium size diesel engine in fixed operational conditions, the issue of back pressure was not addressed. Back pressure can be mitigated by the interposition of a buffer volume, the size of which is a determining factor in system performance, particularly when it is designed to operate over a broad range of engine speed and loading. This paper presents a simplified model of an active flow control exhaust system, which is then applied using a 16 litres, 8 cylinder diesel engine, in order to estimate back pressure, control valve loading and dimension its key components in such a way that back-pressure is maintained below a specified threshold over a broad range of speed and loading.
Full Paper
Development of a voice shutter (Phase 1: A closed type with feed forward control)
Nishimura, Masaharu (1), Tanaka, Toshihiro (1), Shiratori, Koji (1), Sakurama, Kazunori (1), Nishida, Shinichiro (1)
(1) Tottori University, Japan
ABSTRACT
Telephone voice is annoying in public spaces like trains and cafés. The speaking voice was tried to be attenuated by using an active noise control technique. It is called 'Voice Shutter'. Two types of voice shutter, which are open type and closed type, were supposed to be possible. In this paper, a closed type voice shutter with a small vent hole controlled by a feed forward active noise control method was manufactured and tested. In order to develop a small handy type of voice shutter, the distance between the reference microphone and the control speaker should be as short as about 20 mm. The causality law was satisfied by using very high sampling frequency (100kHz) and a high speed signal processor with FPGA. In order to follow the rapid change of voice, partitions with a hole was successfully installed in the voice shutter for the primary path and the secondary path not to be affected by the configuration of a mouth. As the results, the handy scale voice shutter was proved to be feasible.
Full Paper
Applying Active Noise Control Technique for Augmented Reality Headphones
Ranjan, Rishabh (1), Woon Seng, Gan (1), Yong-Kim, Chong (1)
(1) NTU, Singapore
ABSTRACT
With the increased popularity of wearable devices, we are seeing head gears (such as Google glass) that provide augmented visual information. We can also extend augmented information to audible signals to guide users in finding their way, alert user to prominent danger in noisy environment, or simply creating virtual-and-augmented reality gaming platform. In this paper, we outline new approaches in combining real sonic environment and augmented virtual sound source through an open-ear headphones. Microphones are positioned in the headphones to capture the sonic information as well as the signal playback to the headphones. Active noise control (ANC) techniques have conventionally been used for noise cancelling headphones, and this paper shows how we can apply ANC techniques in augmented reality headphones to compensate for the sonic difference between augmented and real sound objects and provide a seamless combination of the two. Some interesting new applications using the augmented reality headphones can be realized with this augmented reality headphones, and open up new possibilities for other interactive applications.
Full Paper
A decoupled hybrid structure for active noise control with uncorrelated narrowband disturbances
Wu, Lifu (1), Qiu, Xiaojun (2), Burnett, Ian S (2), Eva, Cheng (2), Guo, Yecai (3)
(1) Royal Melbourne Institute of Technology, Australia; Nanjing University of Information Science and Technology, China, Royal Melbourne Institute of Technology, Australia
(2) Royal Melbourne Institute of Technology, Australia
(3) Nanjing University of Information Science and Technology, China
ABSTRACT
In real active noise control (ANC) applications, the following situations frequently occur, one is that disturbances only present at the error sensor and have low correlation with reference signal, the other is that there is no enough space or ideal position for locating the reference sensor to satisfy causality condition. Thus the residual noise after feedforward control can be seen as uncorrelated narrowband disturbances in these situations and a hybrid adaptive feedforward and feedback structure is often utilized to cope with this problem. Many efforts have been paid to improve the performance of the hybrid ANC system, nevertheless, few interests are concerned about the combination method between the feedforward and feedback structure. After investigating the conventional combination method of hybrid feedforward and feedback system, this paper introduces an alternate combination method for hybrid ANC system which features that it avoids the coupling between the feedforward and feedback structures and both structures are concatenated to attenuate the ambient noise. Simulations are carried out to validate the effectiveness of the introduced method for ANC with uncorrelated narrowband disturbances.
Full Paper
Using Wind Farm Noise Auralisations for Effective Community Consultation
Butera, Frank (1), Burgemeister, Kym (1), Fisher, Kai (2), Mounter, David (3)
(1) Arup Pty Ltd, Melbourne, Australia
(2) Arup Pty Ltd, Melbourne,
(3) Hydro Tasmania, Hobart, Australia
ABSTRACT
Two of the most common questions that wind farm developers face during community consultation are 'what will the wind farm look like' and 'what noise will it make?' A lot of work has been undertaken recently to develop 'visualisations' or 'photomontages' to answer the first question. However, there has not been an equivalent tool available to enable local communities to understand what a wind farm actually sounds like. Arup and Hydro Tasmania have jointly developed a tool that will accurately and effectively communicate what a wind farm sounds like under different wind conditions and from a range of distances and orientations. This auralisation tool provides a practical and affordable means for the industry to effectively communicate what a wind farm will sound like to the community. This paper looks at how auralisation techniques used in other sectors (such as transport and aviation) have been adapted for the renewable wind energy sector and serve as a valuable tool for increasing transparency, minimising risk and building trust within local communities early in the wind farm development process. It shows how a comprehensive field measurement program at Studland Bay Wind Farm, Tasmania has enabled a wind turbine sound library to be developed for future use in wind farm acoustic models and how calibrated auralisations can be presented at community settings.
Full Paper
The noise characteristics of \'compliant\' wind farms that adversely affect its neighbours
Large, Sarah (1), Stigwood, Mike (1)
(1) MAS Environmental, UK
ABSTRACT
In the UK many wind farms cause complaints of noise despite complying with control limits. Problems relate to reliance on the LA90 index, failure to consider or apply ratings on the context of the sound characteristics and actual human responses due to complex characteristics. In general in the UK low frequency and very low frequency sound effects are either ignored or denied. The complex interrelationship of features within this noise and difficulties in quantifying and qualifying noise impact and inappropriate comparison with other sources of noise renders the effects difficult to investigate or quantify with contradictory outcomes possible using the same data sets. Claim and counterclaim of health and adverse effects complicate the analysis. This paper explores some of the interrelating characteristics of wind farm noise measured and observed in the field that appear to influence complaints made by communities. Cumulative effects occurring in environments normally dominated by natural sounds and both audible and inaudible elements remain alien sounds which are not habituated to. It appears that sensitisation arises. The physical reason for the failure to appropriately identify modulating noise effects and in particular low frequency modulating noise problems are explored.
Full Paper
Initial findings of the UK Cotton Farm Wind Farm long term community noise monitoring project
Stigwood, Mike (1), Stigwood, Duncan (1), Large, Sarah (1)
(1) MAS Environmental, UK
ABSTRACT
This paper provides early results of a long term study of community impact from wind farm noise and uses of the data obtained. A continuously recorded database of noise collected under different meteorological conditions has allowed detailed analysis of particular characteristics such as amplitude modulation and also the reliability of assessment methodologies for predicting and quantifying impact. Surprising outcomes are explored including upwind impact. In 2013 MAS Environmental established a permanent monitoring station to record and publish data online located 600m from the nearest turbine to correlate the impact upon the community and provide an extensive database. This paper maps the evolution of the project. Online data enables a wider study of the effect of meteorological change on noise immission in a flat eastern area of the UK. Anyone can independently observe and listen to the audible elements of the noise that people complain about. This tool aids understanding as well as predicting times of likely adverse impact. The database has enabled testing of proposed controls, particularly in relation to audible amplitude modulation and demonstrated the recent Renewables UK proposed control mechanism fails. Data obtained challenges blade stall research claims as the primary cause of far field AM and wind farm noise prediction methodologies.
Full Paper
The Relevance of the Precautionary Principle to wind farm noise planning
Thorne, Bob
Noise Measurement Services Pty Ltd, Brisbane, Australia
ABSTRACT
Wind farms consist of clusters of industrial wind turbines which, when placed in rural areas, are associated with intrusive and unwanted sound. Wind turbine noise has characteristics sufficiently different from other, more extensively studied, noise sources to suggest that standard industrial noise standards are not appropriate for measurement and assessment purposes. A seven year study is reported and, although limited in population size, it is clear that there are definite adverse health effects related to wind farm noise. Time-aggregated noise metrics have limited utility in assessing individual human health and well-being, and a cluster of metrics are needed to describe and estimate potential effects on individuals and communities. Sleep deprivation is a widely reported occurrence by people in the vicinity of a wind farm. At this time, however, the quantity and quality of research are insufficient to effectively describe the relationship between wind turbine noise and health, and until such time that a definitive relationship is obtained, legislation should apply the precautionary principle and conservative criteria when assessing proposed wind farm developments.
Full Paper
Development of the Microphone-Array Measurement Technique for use in Cryogenic and Pressurized Wind Tunnels
Ahelfeldt, Thomas (1), Spehr, Carsten (1)
(1) DLR, Germany
ABSTRACT
In the development process of aircrafts and rail vehicles, the use of microphone phased arrays to acquire acoustic data on scaled models in conventional wind tunnels has become feasible. Since conventional wind tunnels cannot generally achieve full-scale Reynolds numbers, aerodynamic measurements are performed in cryogenic and/or pressurized wind tunnels which are capable of full-scale/higher Reynolds number flows. The microphone array measurement technique has been further developed for the use in cryogenic (down to 100 K) and pressurized (up to 450 kPa) wind tunnels. The comparison of aeroacoustic results obtained from wind tunnel tests with results from real flight tests shows differences. The differences can be attributed to lack of model-fidelity, installation effects, the Reynolds number and the assumptions made in phased array processing. This work focuses on the effect of the Reynolds number. This paper gives an overview of the efforts at to make microphone array measurement technique available to use in pressurized and cryogenic condition. The aim of this development is to enable acoustic measurements on scaled aircraft models in start and landing configuration at real-flight Reynolds numbers.
Full Paper
Beamforming of aeroacoustic sources in the time domain
Fischer, Jeoffrey (1), Valeau, Vincent (1), Brizzi, Laurent-Emmanuel (1)
(1) Institut P\', University of Poitiers, France
ABSTRACT
A classical array processing technique used for the analysis of aeroacoustic sources is the frequency-domain beamforming technique. The use of this technique requires an assumption on the stationarity of the sources as it works with a time-averaged estimate of the cross-spectral matrix. As a consequence this technique provides an estimation of the average position (in space and time) of an aeroacoustic source. However, some studies, focusing in particular on jet noise, have shown the intermittent nature of some aeroacoustic sources. The aim of this paper is then to show that the time-domain beamforming technique allows assessing the intermittent nature of aeroacoustic sources, and makes possible a space-time tracking of short duration acoustic events occurring in the flow. The method is applied to experimental wind-tunnel measurements. The noise produced by the flow over a forward-facing step is analyzed by using both frequency-domain and time-domain beamforming, and the intermittent structure of such an aeroacoustic source is investigated.
Full Paper
Correlation of parallel car interior and exterior beamforming measurements in a wind tunnel
Neugebauer, Stefan (1), Rösel, Reinhard (1), Döbler, Dirk (1)
(1) GFaI e.V., Germany
ABSTRACT
In aeroacoustics, beamforming measurements have become a standard tool for sound source localization. Additionally, correlation methods are applied to determine the contributions of local wind noise to the measurement. We present a series of synchronized measurements of a car in a wind tunnel, all of them using two beamforming arrays at the same time. One is placed outside the wind stream near the shear layer while the other array is located inside the car's cabin. This setup enables us to localize wind noise transmission into the car's cabin. In the next step, leaks will be ranked by their exterior origins, e.g. side mirror, wheel house etc. by correlating interior and exterior acoustic images. In contrast to this method, we additionally used measurement microphones as reference channels, which is the classic approach up to now. The paper will compare those two methods.
Full Paper
Three-dimensional beamforming of aeroacoustic sources.
Porteous, Ric (1), Prime, Zebb (1), Valeau, Vincent (2), Doolan, Con J (1), Moreau, Danielle (1)
(1) University of Adelaide, Australia
(2) CNRS - Université de Poitiers-ENSMA, France
ABSTRACT
This paper outlines the development and implementation of an alternative beamforming processing technique known as 'multiplicative beamforming'. The technique is well suited to non-planar microphone arrays scanning a three-dimensional (3D) grid. Numerical simulations show that the technique improves 3D spatial localisation by reducing side lobe levels and removing the directional bias of the main lobe of the beamforming output. It can also be used to accurately localise dipole sound sources, which are commonly found in aeroacoustics. The technique has also been applied to experimentally obtained data measured using a non-planar array inside an open-jet anechoic wind tunnel at the University of Adelaide. The experimentally obtained results show good agreement to that of the numerically simulated results.
Full Paper
Beamforming array optimisation and phase averaged sound source mapping on a model wind turbine
Prime, Zebb (1), Doolan, Con J (1), Zajamsek, Branko (1)
(1) University of Adelaide, Australia
ABSTRACT
Beamforming is an array processing technique often used to localise sound sources. This paper details the design and testing of a new planar microphone array in the School of Mechanical Engineering at the University of Adelaide which will be used for localising the noise generation from a model wind turbine. The array microphone locations were found using a constrained bi-objective optimisation to find a good compromise between the array resolution, also known as beamwidth, and the maximum value of spurious lobes, known as the maximum side-lobe level. Aggregate and phase averaged beamforming results of a rotor rig experiment are presented.
Full Paper
Quiet Construction: State-of-the-Art Methods and Mitigation Measures
Cheng, Kin Wui (1), Law, Chi-wing (1), Wong, Cheung-lam (1)
(1) Environmental Protection Department, Hong Kong
ABSTRACT
Alongside with the economic growth, construction activities to cope with the intense demand for infrastructural developments and housing in Hong Kong are at high time in recent years. However, noise from these activities is often a concern to the local communities and it is necessary to strike a balance between the need for meeting tight construction timeframes and the quest for quieter living environment. Typical ways to control noise from construction activities include applying standards for controlling noise at source; site boundaries; and at the receiver such as a residence. No matter which approach is adopted, the use of quieter construction methods, equipment, and effective noise mitigation measures is essential to, both comply with the control requirements and, to certain extent, meet the rising public expectation. This paper will describe the findings from a review on the available state-of-the-art quieter construction methods, equipment and innovative noise mitigation measures. Assessment and analysis of their applicability to Hong Kong situation will be discussed. This paper will also address the issue on promoting wider adoption of these quieter means and enhancing noise awareness through partnership programmes established with the construction trade.
Full Paper
Noise sentinel - a proactive approach to noise management in mining operations at BHP Billiton Worsley Alumina Pty Ltd
Kenny, Silver (1), Manvell, Douglas (2)
(1) BHP Billiton Worsley Alumina Pty Ltd , Australia
(2) Brüel & Kjær Sound & Vibration Measurements A/S, Denmark
ABSTRACT
BHP Billiton Worsley Alumina Pty Ltd (BWAPL) consists of mining operations located near the town of Boddington, a 51km conveyor linking to an alumina refinery located in Worsley and a port load out facility located in Bunbury. BWAPL mining operations expanded in 2012, resulting in mining operations taking place much closer to a number of residential properties in the community and closer to the township of Boddington. Given the proximity of the mining operation to these sensitive receptors, noise was identified early on as a high risk to the operations that needed to be proactively managed to ensure that BWAPL's environmental and social licences to operate were maintained. BWAPL adapted Brüel & Kjær's Noise Sentinel monitoring system to monitor noise generated by mining operations and ensure that the impact on near neighbours was minimised. This was achieved by incorporating alert systems that allowed for proactive management. This paper will cover the compliance parameters required to be measured; the adaptations applied to the software and the key project challenges that were overcome. On the basis of the experiences gained and the positive outcomes achieved through implementing the Noise Sentinel system, BWAPL received a Highly Commended award at the 2013 BHP Billiton Health, Safety, Environment and Community Awards in the Environment category.
Full Paper
Quality Powered Mechanical Equipment System to Reduce Construction Noise in Hong Kong
Law, Chi-wing (1), Wong, Cheung-lam (1)
(1) Environmental Protection Department, Hong Kong
ABSTRACT
Quality Powered Mechanical Equipment (QPME) System is an administrative system in Hong Kong for promoting the use of environmentally friendly construction equipment. It recognizes construction equipment which is newly manufactured, notably quieter, more environmentally friendly and more efficient. The recognition is realized by granting QPME labels for twelve types of equipment that meet the latest European or Japanese requirements. This System is well received and at present, other initiatives such as the "Pay for Safety and Environment" scheme and profit tax concession have been developed concurrently with the QPME system. This paper will describe how the QPME System is operated and evolved since 2005, its benefits to the environment of Hong Kong, and in particular its effectiveness in reducing construction noise in a dynamic city like Hong Kong.
Full Paper
Challenge on Environmental Mitigation Measures on Site Formation Work to Achieve Win-Win-Win Situation for Project Proponent,
Lee, Lawrence (1), Cheung, M K (1), Liu, Alfa (1)
(1) MTR Corporation Limited, Hong Kong
ABSTRACT
The construction of South Island Line (East) is a designated project under the Environmental Impact Assessment Ordinance (EIAO) in Hong Kong. An Environmental Impact Assessment (EIA) tool has been developed for the project and was approved in 2010 during the design stage. An amendment of noise mitigation was further enhanced to suit and optimize their methodology in order to achieve a win-win-win situation for the Project Proponent, the Contractors and the Stakeholders. The EIA defined two main activities for the South Horizons Plant Building works, namely "Slope Stabilization and Rock Slope Excavation". The excavation work was presumed to last for over 2 years by mechanical means involving intensive breaking and drilling with hydraulic breakers and drilling rigs respectively which could potentially generate excessive noise impacts to the nearby high density of residents with nearest 30m away from the work site. This paper gives an overview of challenges on the amendment of EIA which included the technical aspects of blasting operation and noise impact from the proposed alternative construction methodology by using opencast blasting in comparison to the mechanical method presumed, where pros and cons are also examined.
Full Paper
Effective noise objectives for industrial and resource developments - setting, compliance assessment monitoring and audit
Tickell, Colin
Hatch Pty Ltd, Australia
ABSTRACT
As a part of government approval of industrial and resource development projects, limits for noise emissions received in surrounding communities is a required activity. Governments have policies and regulations to set limits which are usually based on either achieving acceptable sound levels for amenity or health, often based on WHO guidelines. Limit conditions based on ambient sound levels become difficult for resource or industrially intensive areas, such as the Hunter Valley in NSW, for both governments and communities if policies are not followed. Monitoring is typically required to demonstrate compliance and specific methods may also be required for this. Demonstrating compliance with limits can be difficult despite extensive permanent monitoring systems. Auditing of the monitoring system and reported results may be rare. This paper reviews typical approaches to setting approval limits in some Australian and Canadian states/provinces and how they are typically monitored to assess for compliance. Limit conditions should be like effective specifications - have a sound level objective, location and conditions for assessment, and method, tolerance and reporting requirements. Some difficulties observed in recent projects are discussed improvements to make both limit conditions and monitoring more effective are suggested.
Full Paper
Noise assessment in the neighbourhood of Italian military airports
Filomena, Vincenzo (1), De Vivo, Luciano (1), Notarnicola, Lorenzo (1), Aversano, Renato (2), Tusciano, Manolo (2)
(1) CIRA, Italy
(2) Italian Air Force, Italy
ABSTRACT
This paper reports the most recent application of the MILNOISE PROCEDURE for the assessment of noise pollution due to training flight operations at Italian military airports. The experimental acoustic characterization of different military aircraft, like C27J, NH500, MB339, AM-X, F-16, EFA, HARRIER, TORNADO, operating in various military airfields, was carried out in the last 10 years. The results of airport acoustic impact on the surrounding environment, with reference to the actual traffic, have been reported in terms of LVA contour plots on 1:25000 scaled maps. In order to minimize the noise impact on inhabited areas surrounding the airfield, both dedicated noise impact evaluation for each aircraft (and for every single noise event such as: take-off, approach, touch & go and flyover) and a specific airport noise assessment with different air traffic scenarios have been carried out. Moreover, a numerical study aimed at evaluating the noise impact of the new F35 military aircraft and at comparing its noise characteristic with present and future military airfield scenarios have been undertaken. All the reported activities have been made in cooperation between CIRA and the Italian Air Force.
Full Paper
Measurement of noise exposure planar distribution in aircraft approach path vicinity
Ishii, Hirokazu (1), Yokota, Takatoshi (2), Makino, Koichi (2), Shinohara, Naoaki (3), Sugawara, Masayuki (4)
(1) Japan Aerospace Exploration Agency, Japan
(2) Kobayasi Institute of Physical Research, Japan
(3) Narita International Airport Promotion Foundation, Japan
(4) Airport Environment Improvement Foundation, Japan
ABSTRACT
Japan Aerospace Exploration Agency is conducting a research project called DREAMS which aims to develop key technologies for future air traffic management systems which will enhance safety, efficiency, user convenience and environmental compatibility of flight operations. One of the research subjects in DREAMS is noise abatement flight technology. Its key element is an aircraft noise prediction model taking into account the effect of meteorological conditions on noise propagation. In order to verify the developed noise prediction model, noise measurement was conducted to obtain the planar distribution of noise exposure below the approach paths. The measurement area was about 4- by 4.4-kilometers and was divided into 110 (11×10) 400- by 400-meter grids. A GPS-synchronized multipoint noise measurement system was placed in every grid. The obtained results proved that the predicted instantaneous noise level and the noise exposure level were in good agreement with the measurement. The average and standard deviation of the noise exposure level prediction error calculated from 2543 data for Boeing 777-300ER were 0.41 dB and 1.50 dB, respectively.
Full Paper
Challenges in Producing an Australian Noise Exposure Forecast
McLeod, Ian (1), Latimore, Mark (1)
(1) Airservices, Australia
ABSTRACT
Commonwealth owned airports are required to produce an Australian Noise Exposure Forecast (ANEF) every 5 years under the Airports ACT 1996. An ANEF is developed using Australian Standard AS2021. In 1999 the Minister for Transport and Regional Services directed Airservices to endorse ANEFs for technical accuracy. This ministerial direction is still current. The interpretation of technical accuracy has changed over the years since 1999. In the past basing a new ANEF on the previous one was an acceptable practice however this is no longer valid. New technology is changing the way aircraft fly. The improved accuracy resulting from modern navigation instruments has allowed (suitably equipped) aircraft to fly with reduced clearances. New flight paths are today being designed to take advantage of these emerging technologies. Though the majority of the current aircraft may not use them, these new flight paths are within the scope of today's ANEFs. In many cases an ANEF will need to predict how ATC will manage operations at close to the airport's physical capacity. A further complication is the tendency of airports to use long range and ultimate capacity ANEFs that try to predict well beyond the normal 20 year ANEF horizon. This paper examines the common issues past and present that Airservices has had to deal with in carrying out its obligations for technical endorsement of ANEFs and ANEIs.
Full Paper
Reliability of aircraft noise evaluation by measurement for comparison with prediction
Shinohara, Naoaki (1), Yamada, Ichiro (2)
(1) Narita International Airport Promotion Foundation, Japan
(2) Aviation Environment Research Center, Japan
ABSTRACT
This paper discusses the reliability of measured airport noise evaluation compared with prediction. In Japan, airport noise mitigation measures are performed based on yearly-average airport noise predictions. It is necessary to realize a high reliability in predictions, which are determined by comparing them with noise measurements in order to confirm their validity. However, various factors including microphone height, SN ratio and SEL calculation procedure and incomplete observations affect the reliability of measured noise evaluation. When evaluating yearly-average aircraft noise using short-term measurements, the reliability changes dependent on the measurement period in addition to the afore mentioned factors. Thus, it is necessary to estimate the long-term average using short-term noise measurements and result of continuous noise monitoring or average aircraft operation number. The sound of airport ground activities such as APU or taxiing can be heard in the surroundings of the airport, but the sound propagation significantly changes dependent on meteorological conditions. In other words, airport ground noise becomes louder and audible only in cases of favorable conditions for sound propagation. But, evaluation of yearly-average sound exposure due to aircraft noise requires average-day sound exposure of the year. So, it is necessary to consider what conditions we should suppose for noise measurement.
Full Paper
Angular and distance dependence of the standard deviation of maximum sound level for aircraft noise
Wall, Martin (1), Liljergren, Mikael (1), Heed, Christer (1), Tari, Alborz (1)
(1) Swedavia, Sweden
ABSTRACT
The current method to calculate number above threshold (NAT) in Sweden does not take into account the natural variation of sound level arising from variations in the sound emission and sound propagation. This leads to unrealistic discontinuities in the calculated noise contours as all movements of a specific aircraft type with a specific procedure are assumed to generate the same maximum sound level. Using long term measurements, the standard deviations of maximum sound levels are analyzed after dividing the airspace around the microphones into sections depending on the elevation angle and distance from aircraft to microphone. The standard deviation in each section is determined by calculating the standard deviation of each aircraft type that passes through that section and combining the aircraft type specific results into one figure. The standard deviation varies from about 1 dB to 3 dB with generally higher values the greater the slant distance and the smaller the elevation angle. The found standard deviations are presented in polar diagrams and are implemented in NAT calculations. The resulting noise contours are not only smoother and without discontinuities, but they are also a better representation of what NAT stands for.
Full Paper
Land-use planning at airports in Germany
Weinandy, Rene (1), Myck, Thomas (1), Thierbach, Roman (1)
(1) Federal Environment Agency, Germany
ABSTRACT
In 2001 the International Civil Aviation Organization (ICAO) initiated the Balanced Approach to Aircraft Noise Management. It consists of four essential elements to reduce aircraft noise. One is land-use planning and management. In Germany, this already starts with planning of an airport in order to find a suitable site. This planning process deals with aircraft operational aspects as well as economical and environmental ones. After the airport has been built, noise protection areas are to be established according to the German Act for Protection against Aircraft Noise. The noise protection area is subdivided into two daytime and one nighttime protection zone. The act oblige the airport operator to pay for constructional soundproofing measures in existing residential buildings located in daytime protection zone 1 and in the nighttime protection zone. Moreover, expenses for installation of ventilation systems in rooms predominantly used for sleeping are to be reimbursed by the airport operator for buildings in the nighttime protection zone. Furthermore, several local regulations which comprise building restrictions in the vicinity of the airport exists which primary have the aim to prevent or reduce noise conflicts. The land-use planning at German airports will be described and evaluated.
Keywords: Airport, Noise, Insulation
Full Paper
Numerical modelling of the vibro-acoustic behavior of a closed vehicle with frequency dependent polymer materials
Bouayed, Kaiss (1), Mordillat, Philippe (2), Mebarek, Lassen (1), Hamdi, Mohamed Ali (3)
(1) ESI Group, France
(2) Renault, France
(3) University of Technology of Compiegne, France
ABSTRACT
In this paper, the vibro-acoustic response of a closed vehicle (Renault B95) is computed using a prototype tool based on the VPS software developed by ESI Group. This prototype tool takes into account the frequency dependence of the modulus of viscoelastic materials represented by the PVB of the windscreen and joints between the vehicle's body and glass surfaces. In a first step, the accelerations at different points of the windscreen and pressures inside the cabin are computed and compared to those obtained by NASTRAN software. In a second step, these results are compared with experiments obtained by Renault using accelerometers and those obtained by the University of Technology of Compiègne using a 3D laser vibrometer. Comparisons show an acceptable agreement between different numerical and experimental results.
Full Paper
Research on vibration and sound radiation characteristics of ship stiffened composite plate structure
Pang, Fu-zhen (1), Song, Hong-bao (1), Miao, Xu-hong (2)
(1) Harbin Engineering University, China
(2) Naval Academy of Armament, China
ABSTRACT
Based on Statistical Energy Analysis method, the vibro-acoustic characteristics of stiffened composite plates are investigated in this paper. First, the vibration theoretical model of the stiffened composite plate is developed by using the Hoff sandwich plate theory. The method to calculate the modal loss factor of stiffened composite plate structure is proposed. Then the influence of damping layer thickness, elastic modulus and constraint layer elastic modulus on the vibro-acoustic characteristics of the stiffened composite plate has been studied. The results show that the above three parameters have a great impact on the structural vibro-acoustic characteristics. On this base, the vibro-acoustic characteristics of the cabin segment in composite are investigated. The influence of different constraint damping structure parameters and laying positions on the ship vibration radiation are analyzed. Results show that the laying location of constrained layer damping (CLD) has a great impact on the acoustic radiation reduction. The constrained layer damping laid in the excitation source place can achieve better acoustic radiation reduction.
Full Paper
Optimal design of unconstrained damping material on a thin panel by using topology optimization
Yamamoto, Takashi (1), Yamada, Takayuki (2), Izui, Kazuhiro (2), Nishiwaki, Shinji (2)
(1) Kogakuin University, Japan
(2) Kyoto University, Japan
ABSTRACT
Damping material is usually applied on the steel panel of a vehicle to reduce vibration level. On the other hand, the weight reduction is also required to improve fuel consumption. Therefore, modal loss factors in- duced by damping material on the steel panel of a vehicle body structure need to be maximized with a given volume. In this paper we propose a practical design method to maximize modal loss factors by optimizing the material distribution of damping material under a prescribed volume constraint. The modal loss factor of an eigensmode can be written as the ratio of the strain energy stored in the damping material over the total strain energy in the system under consideration. In the proposed method, we assume the eigenvectors are almost the same as the eigenvectors when damping material is removed. The modal loss factor can then be expressed by using a corresponding eigenvalue where the mass density of the damping material is ignored whereas the stiffness is taken into account. Several numerical examples are provided to show the optimal distributions of the damping material by using a flat panel. Damping material is distributed in the domain where the strain en- ergy is stored, which agrees well with our experiences. Moreover, by applying a sensitivity filter that utilizes a weighted average of design sensitivities over local area, damping material can be distributed collectively in a single domain to meet practical requirements for manufacturing,
Full Paper
Stochastic porous model of a bone-implant healing process using polynomial chaos expansion
Yang, Ji (1), Faverjon, Béatrice (2), Dureisseix, David (3), Swider, Pascal (4), Kessissoglou, Nicole (1)
(1) UNSW Australia, Australia
(2) UNSW Australia, Australia & Université de Lyon, France
(3) Université de Lyon, France
(4) IMFT UMR 5502 CNRS-INPT-Toulouse 3, France
ABSTRACT
Porous material is used in engineering and biomedical structures, where the solid phase is the frame of the material and dissipation effects occur in the pores of the material. This work proposes a stochastic model of porous material to predict the bone tissue healing process in the early period after the implantation surgery. The bone implant is assumed to be axisymmetric and the healing process is evaluated up to 8 weeks after the implantation, which is validated by the canine experiments. The porous dynamic model is coupled with biochemical equations to take into account the osteoblast cells migration and the growth factors diffusion. Using the polynomial chaos expansion method, the effects of uncertain biochemical factors on the distribution of the new-formed tissue around the bone implant are examined. Compared with Monte Carlo simulations, the stochastic model can obtain high accuracy with greatly improved computational cost. The spatial-temporal model presented here provides a tool to evaluate the highly complex implant healing process and the influences of different biochemical factors.
Full Paper
Optimal Configurations of ACLD/Plate for Bending Vibration Control using INSGA-II
Zhang, Dongdong (1), Zheng, Ling (1), Li, Yinong (1)
(1) Chongqing University, China
ABSTRACT
Active constrained layer damping (ACLD) has been demonstrated as an effective means of vibration and noise control for flexible structure. The overall performance of ACLD system is governed by the performance of the passive and the active controls on which the configurations of ACLD treatments have significant effect. In this paper, a multi-objective optimization model for ACLD treatments is established based on the finite element model of the plate partially covered with ACLD treatments. The improved non-dominated sorting genetic algorithm (INSGA-II) is developed to obtain the optimal configurations of ACLD treatments for vibration control of bending modes of the plate. In the optimization procedure, an integrated multi-objective optimization strategy is proposed, in which the passive and the active controls performance are considered simultaneously. The modal loss factors and the frequency response excited by the unit control voltage are selected as the passive and active control objectives, respectively. The location-numbering of the ACLD patches and the thickness of the viscoelastic materials (VEM) and piezoelectric material (PEM) are served as design variables. The vibration control results show that the better results of vibration control can be achieved in passive and active control when the optimal ACLD treatments are employed.
Full Paper
Removal of shaft speed related components from the response signals of a machine with varying speed prior to Operational Modal Analysis
Coats, Michael David (1), Randall, Robert Bond (1)
(1) UNSW, Australia
ABSTRACT
It is an advantage to remove discrete frequency components from response vibration signals before carrying out operational modal analysis (OMA), because they tend to disrupt the operation of normal OMA algorithms. The removal of such components can be achieved by carrying out order tracking, to remove the effects of speed variations by resampling with a fixed number of samples per period of the frequencies to be removed, so that they are in discrete lines in the order spectrum, and can then in principle be removed by techniques designed for constant speed machines. If the speed variations are greater than 1% or so, the spectrum of the order tracked signals is no longer a frequency spectrum, so modal properties, which are related to frequency, can no longer be obtained by OMA. This paper introduces a method where signals are transformed into the order domain, and after the removal of shaft speed related components are transformed back to the time domain to allow normal OMA to be applied. The method is demonstrated using signals from a gearbox casing excited (via a shaker) with a varying frequency signal containing 22 harmonics corresponding to speed variations of ±15%.
Full Paper
A detailed experimental modal analysis of a clamped circular plate
Matthews, David (1), Sun, Hongmei (2), Saltmarsh, Kyle (2), Wilkes, Daniel Ryan (3), Munyard, Andrew (1), Pan, Jie (2)
(1) DSTO, Australia
(2) UWA, Australia
(3) Curtin Uni., Australia
ABSTRACT
A detailed study has been made of the natural frequencies and modal shapes of a thin steel disc that is clamped at the edges by two steel flanges. The aim was to determine how accurately numerical modeling could be used to predict the results and to investigate the possibility of any new experimental observations even for this simple structure. A mechanical shaker and impact hammer were used to excite the plate to obtain the frequency response function of the structure. The first eight modal shapes at each of the resonant frequencies were then measured using laser scanning vibrometry. These results were compared with theoretical results obtained analytically and numerically using PAFEC. While part of the existing understanding of the plate vibration was confirmed, significant differences were found in the values of the modal frequencies. The experimental data also demonstrated a dependence of the mode shape orientations and splitting of degenerated natural frequencies on the shaker position and properties of the flanges. This paper will report on some interesting effects that need to be considered when doing such measurements and illustrate the risks of using numerical modeling without the use of experimental comparison.
Full Paper
Automotive cabin characterization by acoustic modal analysis
Peeters, Bart (1), El-kafafy, Mahmoud (2), Accardo, Giampiero (1), Bianciardi, Fabio (1), Janssens, Karl (1)
(1) LMS International, Belgium
(2) Vrije Universiteit Brussel, Belgium
ABSTRACT
The interior sound perceived in an automotive cabin is a very important attribute in vehicle engineering. Therefore, there is an industrial interest to be able to predict the interior acoustic behaviour by means of accurate simulation models. In order to understand the modelling challenges and improve the modelling know-how, experimental methods in which an acoustic characterization of the cabin is performed based on measurements play an important role. When performing an interior acoustic study, it is important to relate the acoustics responses to the intrinsic system behaviour of cabin cavity. This can be done by means of acoustic modal analysis, i.e. modal parameter estimation methods decompose the system behaviour into a set of individual resonance phenomena, each characterised by a resonance frequency, damping ratio, and mode shape. This paper will discuss the equipment requirements and advanced modal parameter estimation techniques. Specific acoustic modal analysis challenges are the high modal damping ratios resulting in highly overlapping modes with complex mode shapes and the use of a large number of references (sound sources) distributed around the cabin to get a sufficiently homogeneous sound field. The performance of Maximum Likelihood Estimation will be examined and compared to more traditional approaches.
Full Paper
Regeneration of frequency response functions from poles and zeros: a discussion with implications for cepstrum-based operational modal analysis
Smith, Wade A (1), Randall, Robert Bond (1)
(1) University of New South Wales, Australia
ABSTRACT
Operational modal analysis (OMA) seeks to determine a structure's dynamic characteristics from response-only measurements, which comprise both excitation and transmission path effects. The cepstrum has been used successfully in a number of applications to separate these source and path effects, after which the poles and zeros of the transfer function can be obtained via a curve-fitting process. The contributions from the individual poles and zeros can then be added (in log magnitude) to regenerate the frequency response function (FRF). This paper discusses a number of observations relating to this FRF regeneration process, as well as a number of broader points explaining FRFs from a pole-zero perspective. Among the topics covered in the discussion are: the required distribution of poles and zeros for the successful regeneration of FRFs; node points and weak modes in a pole-zero model; the differences in pole-zero distribution between receptance, mobility and inertance FRF forms; and, how to deal with the very low frequency region when regenerating FRFs. It is hoped that the discussion will assist in the application of cepstrum-based OMA methods and will lead to improved understanding of the FRF regeneration process and of frequency response functions more broadly.
Full Paper
Using frequency and modal analysis to attenuate low frequency waves
Ziaran, Stanislav
Slovak University of Technology, Slovakia
ABSTRACT
The paper analyzes the response of structures and machinery to low frequency vibration (LFV) such as low frequency waves (industrial seismic waves) generated by different machines, technological processes, etc. The principles of the analysis can be applied for different kinds of excitation (stationary - deterministic, random and non stationary - continuous and variable). Some sources, as a result of human activity, for LFV and their subsequent low frequency waves (LFW) were investigated and analyzed. The goal was to determine the Eigen frequencies and Eigen modes of the measured structure and/or machinery not only by identifying sources of vibration but also applying operational modal analysis which is important in designing suitable modal damping. The operational frequency spectrum with Eigen modes of the structure and/or machinery is compared by means of frequency and modal analyses. Through modal damping, levels of low frequency noise may follow, and the transmitted LFV can be the reason why resonance or excitation of the Eigen modes occur. In the conclusions, the measured results of the LFW caused by a vehicles combustion engine is analysed as well as its effect on the cabin of the vehicle. Similarly electromotor resonance is investigated as well. The results of the frequency analysis, and the resulting measurements show the most effective way to attenuate high energy LFW.
Full Paper
Prediction of Acoustic Performance of Composite Steel Floors
Ballagh, Keith Orsbourn (1), Chung, Hyuck (2)
(1) Marshall Day Acoustics, New Zealand
(2) Auckland University of Technology, New Zealand
ABSTRACT
One method of constructing lightweight concrete floors in residential dwellings is to use a trapezoidal profile steel pan as a permanent form for a relatively thin pour of concrete. The resulting structure has enhanced stiffness to weight ratio due to the composite action between the steel and concrete, and the inherent improved stiffness of the profiled cross section. However the floor is strongly orthogonal and the composite action makes the bending stiffness's difficult to calculate. Common models for predicting the sound insulation of panels are not accurate. Heckl has provided a solution for the sound transmission of an orthogonal panel, which requires a double numerical integration, however this is time consuming to solve especially if accuracy at high frequencies is required. The current work reports a successful use of ANSI C-2011 Standard for Composite Floors to calculate the bending stiffness's of the floor in orthogonal directions and implementation of a Gauss- Legendre method for carrying out the double integration.
Full Paper
Flanking sound transmission in an innovative lightweight clay block building system with an integrated insulation used at multifamily houses
Buchegger, Blasius (1), Ferk, Heinz (1), Meissnitzer, Marlon (1)
(1) TU Graz, Austria
ABSTRACT
Accurate calculations in building acoustics depend amongst other on matching values of the vibration reduction index kij in component nodes. The usage of common calculation methods based on the mass-ratio of homogeneous materials may fail in complex wall and ceiling structures, so measurements of the values are necessary. In this paper, a comprehensive experimental determination and analysis of the vibration reduction index according to EN ISO 10848-1 on an innovative lightweight clay block building system with integrated thermal insulation is presented. For this purpose, a mock-up consisting of 3 rooms at 2 floors was created in real-size according to the standardized specifications. Investigation shows, that on the one hand, the increased inner damping due to the integrated thermal insulation and on the other hand, modal phenomena in the low-frequency range can cause problems by determining the necessary vibration level differences. To get reliable results, comprehensive analysis on the masonry are performed. A combination of experimental modal analysis and computer-based FEM-simulation models allows a deep insight into the resonant behavior of the entire wall structures, as well as the individual brick. It is shown that the positioning of the measurement positions possibly can have strong effects on the resulting values.
Full Paper
Approximate formulae for the average one sided specific radiation wave impedance of a finite rectangular panel
Davy, John Laurence (1), Larner, David James (1), Wareing, Robin R (2), Pearse, John R (2)
(1) RMIT University, Australia
(2) University of Canterbury, New Zealand
ABSTRACT
The authors have previously published approximate formulae for the average one sided specific radiation wave impedance of a finite rectangular panel mounted in a rigid infinite baffle. The panel's transverse vibration was due to a (possibly forced) two dimensional bending plane wave propagating in the panel without reflection at the edges of the panel. The average was over all the surface area of the panel and over all possible azimuthal angles of propagation direction. The radiation from waves propagating in different directions was assumed to be uncorrelated. These approximate formulae were derived from the 1982 research of Thomasson whose approximate formulae only covered the high and low frequency regions and not the mid frequency region. This paper presents more accurate versions of some of the approximate formulae. When the bending wave number is larger than the wave number of sound, the real part of the impedance is smaller than that for the case studied by Maidanik and Leppington. This is because correlated reflections are not included the case analyzed in this paper. When the bending wave number is smaller than or equals the wave number of sound, the real part of the impedance is the same for both cases.
Full Paper
A new building acoustical concept for lightweight timber frame constructions
De Geetere, Lieven (1), Ingelaere, Bart (1)
(1) Belgian Building Research Institute, Belgium
ABSTRACT
In this paper, a new building concept for multi-family lightweight timber frame housing is proposed. This concept combines party walls, floors and façade elements ensuring comfort levels equal or better than currently encountered in typical Belgian heavy constructions. Low frequency behaviour and prefabrication potential were the key points in the design process of the new wall and floor types. Nevertheless, structural aspects, fire safety issues and thermal capacity have been taken into account as well. Solutions were found by maximally exploiting the mass-spring-mass mechanism. Finally, a holistic approach was followed to develop a building concept in which the walls, floors and façade elements are connected in an optimized way.
Full Paper
Measurements of junction vibration level differences of timber framed constructions
Homb, Anders
NTNU, Norway
ABSTRACT
Flanking transmission of supporting walls of timber framed constructions limits the sound insulation properties in multi storey buildings. Both transmission from the floor construction to the supporting walls and the transmission from wall to wall and to either floor or ceiling through the junction is a part of this challenge. This article presents a method of how to measure the vibration transmission properties well fitted for in-situ measurements. The method is applied on some common Norwegian solutions and results will be presented and compared with similar results from other investigations. There is also a lot of research going on to improve the calculation of sound insulation in lightweight constructions according to EN-ISO 12354. Beside the method itself it includes studies on necessary input data regarding the vibration index, Kij and vibration level difference. The article will give some contribution regarding the distribution of the vibration level from the in-situ measurements.
Full Paper
The Optimization of a Wooden Floor Design Based on Validated Finite Element Models
Mahn, Jeffrey (1), Hopkins, Carl (2), Filippoupolitis, Marios (2), Schanda, Ulrich (3), Völtl, Raphael (3), Krajči, Luboš (4)
(1) National Research Council Canada
(2) University of Liverpool, UK
(3) Rosenheim University of Applied Sciences, Germany
(4) Soundtherm Ltd. Elgg Switzerland
ABSTRACT
This paper describes a research project to develop a dowelled joist floor design which has a similar thickness to typical concrete floor constrictions in Switzerland but with better environmental life cycle impact and impact sound insulation below 200 Hz. The dynamic properties of the floor designs were evaluated using a systematic process of developing and then elaborating on initially simple finite element models which were validated based on experimentally determined material properties. This approach was successful with close agreement in both the mode frequencies and the MAC values. Results from the finite element analysis are presented as are the results from impact testing of full scale floor designs.
Full Paper
Development and sound absorption of interior adjustable acoustical panels
Chou, Chuan-wen (1), Lai, Rong Ping (2), Chien, Shao-Chun (1), Yeh, Po Hung (1)
(1) National Cheng Kung University, Taiwan
(2) NCKU Research and Development Foundation
ABSTRACT
Used the small scale listening room as the example, changed the interior sound field required to redecoration entire room also demand more construction budget; so it is important to development a product could adjustment the sound field also independent from the interior decoration. First, analysis sound absorption, installation, specification of existing acoustics panels on the marketing. Second, based on sound absorption theory to development acoustics panels what could adjustment the reverberation time. This subject designed an acoustical panel what could change the faceplate and structure for the condition without changing interior decoration to satisfy different interior acoustical demand, also maintain independence, include PP (Perforated Panel) and GMP (Geometry Micro-perforated Panel) as acoustics panel's faceplates. The experiments followed CNS 9056 (Measurement of sound absorption in a reverberation room) to evaluated acoustics panels sound absorption performance for the effect factors between installation modes and faceplates. The results of the measurement in the study were shown two parts. One was the influence of equivalent sound absorption area caused by acoustics panels installation modes, and the other was the influence of equivalent sound absorption area caused by changing the faceplate. Above all, the acoustics panel was suitable to adjust the reverberation time without redecorating entire room, and the adjustable interior sound field would be shown.
Full Paper
Theory and three-dimensional numerical simulation of sound propagation along a long enclosure with side opening
Chu, S H K (1), Tang, Shiu Keung (1)
(1) The Hong Kong Polytechnic University, Hong Kong
ABSTRACT
The sound properties along a long rectangular enclosure with a circular source on the top wall and rectangular opening at the side wall are studied. A mathematical model of average pressure at an opening contributed by the sound source and assuming air piston at the opening is derived in terms of the acoustic mode for a rigid duct. Three-dimensional numerical modelling is conducted to compare the theoretical prediction. The computational domain of interest is a long rectangular block associated with an opening connected to a free field environment. Non-reflecting portion is applied to each end of the domain. Sound pressure variations of discrete propagating mode are investigated. Interactions between the resonance of closed duct and effect of the opening are demonstrated at various frequencies. Comparisons indicate that the theoretical predictions give consistent results with that of numerical models. Precision of the radiation impedance of aperture is found crucial to the accuracy of mathematical model. This study approach including the theory and simulation provides a constructive framework for further examination of related subjects.
Full Paper
Generalized alternative image theory to estimating sound field for complex shapes of indoor spaces
Kong, Byunghak (1), Lee, Kyuho (1), Jang, Seokjong (1), Park, Seo-Ryong (1), Lee, Soogab (1)
(1) Seoul National University, South Korea
ABSTRACT
An alternative image theory that can efficiently simulate sound propagation inside a closed space, especially multiple reflections, is proposed. This method defines image spaces according to configuration of a real space, and image receivers instead of image sources are allocated with respect to their local coordinates. As compared to the original image theory, the alternative theory is more effective to develop propagation paths involved with reflections regardless of condition variables such as the number of reflections and combinations of reflecting surfaces. The positions of image receivers located in an image space corresponds to where sound waves that experiences the specific number of reflections related to the order of the image spaces reach to real receivers. Therefore, the sound field inside the real space is obtained by inverting the entire image spaces into the real space, which implies superposition. Basically, it is applicable to convex spaces, e.g. a rectangular hexahedron. Also, concave spaces and spaces that have partitioned into sub-spaces can be covered by the alternative theory.
Full Paper
Reducing Noise and Optimizing Sound within Working Spaces
Probst, Fabian
DataKustik GmbH, Germany
ABSTRACT
Caused by various studies underlining the negative effects of noise exposure and insufficient sound quality within workspaces, this topic receives a growing public attention. These negative impacts include stress symptoms, cardiovascular problems, communication problems and a reduced productivity. In contrary to environmental noise problems caused by infrastructure (aircraft noise, road noise etc.), the responsibility of noise problems within work spaces is distributed among millions of different companies which all require individual solutions. In order to tackle this problem, the German Ministry of Commerce commissioned a project with the objective to develop a procedure to efficiently assess the acoustical situation within workspaces and as a second step to enable the analysis of different measures for improvement. The modeling of complex machinery, speaker systems or people as a sound source must be enabled in order to meet the given objective. At the same time the process should facilitate the comparison of various measures for noise reduction like screens, absorbing baffle ceilings or different workshop layouts. Furthermore and in order to enable a wide base of usage, this procedure needs to be accurate and at the same time easy to apply. This paper provides an overview of research problems, possible solutions and existing techniques.
Full Paper
Parameters design of a nonlinear membrane absorber applied to an acoustic cavity
Shao, Jianwang (1), Wu, Xian (1)
(1) Tongji University, China
ABSTRACT
The targeted energy transfer (TET) phenomenon has been demonstrated and analyzed between an acoustic medium inside a parallelepiped cavity and a thin viscoelastic membrane that is mounted on one wall of the cavity and that is working as a nonlinear absorber or a nonlinear energy sink (NES). Based on the desired working zone of the NES and the two thresholds of the zone which have been obtained, this paper investigates the parameters analysis of a nonlinear membrane absorber to design the NES. The physical parameters of the membrane and the place of the membrane on the wall of the cavity are studied. It can finally provide us to determine where is the better place for the membrane and which parameter affects mainly the desired working zone for the NES.
Full Paper
Finite element sound field analysis for correction of absorption coefficient in reverberation room
Tomiku, Reiji (1), Otsuru, Toru (1), Okamoto, Noriko (2), Okuzono, Takeshi (3), Azechi, Yoshiki (1), Yoshida, Tsuyoshi (1)
(1) Oita University, Japan
(2) Ariake National College of Technology, Japan
(3) Kobe University, Japan
ABSTRACT
In this study, sound fields for the measurement of sound absorption coefficient by reverberation room method are analyzed by time domain finite element method. This study shows effectiveness of the analysis for investigation on causes of variation in the measurement results and improvement methods of the measurement. To evaluate an actual sound field for the measurement, the ratio of incident sound energy to the test material in those to all boundary of the measurement sound field is calculated from results of the finite element sound fields analysis. First, square sound pressure amplitudes of plane sound wave incident on absorption material are calculated in one-dimensional sound field. Next, the calculation method of the ratio of the measurement sound field is described. Finally, relationship among the ratio, shape of the measurement room, and characteristics of the test material is investigated, and it is shown that the bigger normal incident sound absorption coefficient of test material, the larger the change of the ratio for decay sound field regardless of room shape and surface area of test material.
Full Paper
Study of high frequency noise from electric machines in hybrid and electric vehicles
Bassett, Timothy Whitehead (1), Tate, Simon (1), Maunder, Matt (1)
(1) Ricardo, UK
ABSTRACT
This study investigates the tonal high frequency noise characteristics which are present within the cabin of an electric vehicle. As the human ear responds differently to different frequencies of sound and this response varies with age, both the level and the frequency are considered. In addition, the amount of annoyance these sounds will cause for the occupants is a function of the tonality and the level of the noise compared to other masking noise sources present. Metrics for tonal noise taking account of these factors are evaluated for a vehicle creep load case and compared to subjective results to determine suitability for the evaluation of electric vehicles. The Stevens VI loudness metric is shown to give a good indication of the total tonal noise present in the cabin of an electric vehicle. The tone-to-noise ratio and prominence ratio are used successfully to compare the level of a tone to the masking noise present, although general prominence limits are shown to be unreliable for evaluation of electric vehicle tones. Finally the noise sources present in the vehicle are reviewed along with factors that must be considered for the diagnosis and mitigation of these different tonal noise sources.
Full Paper
Comprehensive Automotive Active Sound Design part 2: Operational Sounds and Brand Sound
Belschner, Torsten (1), Bodden, Markus (1)
(1) neosonic, Germany
ABSTRACT
The basic approach for comprehensive Active Sound Design has been introduced in (1). In addition to the sound generation for electric and combustion vehicles discussed there, hybrid vehicles require specific treatment: on the one hand the transition between electric and combustion drive modes has to be harmonized, on the other hand the characteristics of the different modes have to be maintained. This is achieved by a combination of the signature-based approach and the order-based approach. Besides engine sounds the global approach proposed here also generates and supports operational sounds: it synthesizes feedback sounds aligned to the actual vehicle parameters, thereby optimizing the Sound Quality process in terms of time and costs. The harmonization of all vehicle sounds in combination with the sound signature approach allows the realization of a Brand Sound. Starting from verbal brand descriptors this specific approach transports the Brand Identity into each vehicle. Since such a comprehensive approach has to be implemented into the vehicles specific attention has to be paid to the possibilities of the vehicle adaptations.
Full Paper
Comprehensive Automotive Active Sound Design part 1: electric and combustion vehicles
Bodden, Markus (1), Belschner, Torsten (1)
(1) neosonic, Germany
ABSTRACT
The optimization of vehicle sound does not only require the optimization of each component, but the optimization of the combination of the different sounds in order to achieve a homogenous and effective overall sound. Active Sound Design methods offer new possibilities to achieve this ambitious aim, and furthermore to align the overall sound to the Brand Identity. neosonic has developed the modular comprehensive Active Sound Design system elvis3 (ELaborate Vehicle Integrated Sound Signature System) which integrates all audio aspects of the vehicle into one comprehensive tool chain. One component of the system, elvis3 e-motion, is the world's first system used in series in an electric vehicle to create interior vehicle sound (AMG SLS ED Coupe). With the innovative signature-based approach the AMG sound of the 21st century has been realized. A second component, elvis3 Cesar, implements sophisticated support for vehicles with combustion engines using refined signal processing. These two components will be explained in detail along with the flexible system concept. Advanced system modules and applications are part of the second presentation.
Full Paper
Measurement and analysis of the interior noise
and the transfer path of acoustic phenomena into the driver cabin of a battery electric vehicle
Fischer, Jan (1), Behrendt, Matthias (1), Lieske, Dirk (2), Albers, Albert (1)
(1) Karsruhe Institute of Technology, Germany
(2) Daimler AG, RD/FNP
ABSTRACT
Driving comfort is an important factor for buying decisions. This is especially apparent in battery electric vehicles (BEV) where the acoustic quality is an elementary distinguishing feature, since the masking of an internal combustion engine (ICE) is no longer present. Despite the importance of the acoustic quality, there is a general lack of knowledge of how to measure and interpret the high frequency noise generated by an electric powertrain with respect to the NVH behavior influencing the passengers.In this contribution, the measurement results of the interior noise of a battery electric vehicle are analyzed. Specific methods for determining the torsional vibration of the powertrain as reference value are also presented. Furthermore, a method for measuring and interpreting the transfer path of acoustic phenomena from the drivetrain of a battery electric vehicle into the passenger cabin is presented.The measurements are performed in the context of the IPEK-X-in-the-Loop Framework on a roller test bench in a semi-anechoic chamber.
Full Paper
Vibro-acoustic measurements and techniques for electric automotive applications
Sarrazin, Mathieu (1), Gillijns, Steven (1), Janssens, Karl (1), Van Der Auweraer, Herman (1), Verhaeghe, Kevin (2)
(1) LMS International, Belgium
(2) Inverto, Belgium
ABSTRACT
In this study, noise and vibration measurements were carried out on a multi-phase 12/8 switched reluctance (SR) motor and analyzed with vibro-acoustic techniques. When evaluating the behavior of electric powertrains for automotive applications, it is necessary to perform a vibro-acoustic analysis, particularly in view of the acoustic comfort perceived by the driver and passengers. High frequency tonal noise can be very annoying and even causes long term damage. Therefore, the noise and vibrations must be deliberately optimized. In case of a SR motor, the radial magnetic forces between the stator and rotor are the main excitation source, yielding large deformations of the stator housing and emissions of noise. Measurements and simulation results are compared for different load conditions. The dominant vibration modes are analyzed with modal analysis techniques. The unpleasant tonal noise of the motor is objectively quantified by noise metrics. Finally, the relationship between the current profiles, radial magnetic forces, and mechanical and acoustical vibrations is investigated in order to obtain a better understanding of the mechanisms underlying the vibro-acoustic behavior of the motor.
Full Paper
Vibration Control of In-Wheel SRM for Electric Vehicle Applications
Sun, Wei (1), Li, Yinong (1), Xu, Guangzhong (2), Zhang, Nong (2)
(1) The State Key Laboratory of Mechanical Transmission, Chongqing University, China
(2) School of Elec, Mech and Mechatronic Systems, University of Technology Sydney, Australia
ABSTRACT
The Switched Reluctance Motor (SRM) processes great application potential in In-Wheel Motor (IWM) electric vehicles (EV). However the problem of vibration and noise is always a disadvantage of this kind of motor. By utilizing the analytical Fourier fitting method, a convenience method for modeling In-Wheel Switched Reluctance Motor (IW SRM) is proposed for EV applications. And the negative vibration and noise effect of IW SRM on vehicle is investigated according to the unbalanced residual lateral force. Then corresponding control methods are proposed, modified and compared. The proposed combined vibration feedback control of current chopping with PWM can effectively reduce the SRM residual force and ensure the required vehicle speed, though some small low frequency force response is induced.
Full Paper
Results from first Danish full scale test section with poroelastic road surface
Bendtsen, Hans (1), Stahlfest Holck Skov, Rasmus (1), Andersen, Bent (1), Cesbron, Julien
(1) Danish Road Directorate, Denmark
ABSTRACT
The first Danish test section with poroelastic road surface (PERS) was constructed on August 27th 2013 at the Kalvehave test site in Denmark, as a part of the EU project PERSUADE. The test section is 75 m long and has the width of one driving lane. The yearly daily traffic is 4000 with 10 % heavy vehicles. The speed limit is 80 km/h and the estimated real speed is somewhat lower. The pavement is optimized for low emission of tyre-road noise by using a high built in air void, small aggregates and elastic material. The pavement has a porous structure and is composed of stone and rubber aggregates with a maximum aggregate size of 5 mm and the binder used is polyurethane. The pavement type has been developed and tested in the laboratory. An intensive monitoring program was started at the Kalvehave test site even before the test section was opened for normal traffic. The monitoring program includes measuring noise, acoustical absorption, elasticity, permeability, friction, rolling resistance and visual inspections. Measurements of noise using the SPB road side and the CPX trailer methods have been repeated continuously over the first 9 months of the lifetime of the PERS pavement.
Full Paper
Tyre/road noise reduction by a poroelastic road surface
Ejsmont, Jerzy (1), Swieczko-Zurek, Beata (2), Sandberg, Ulf (2), Mioduszewski, Piotr (1)
(1) Technical University of Gdansk, Poland
(2) Swedish National Road and Transport Research Institute, Sweden
ABSTRACT
Low noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory at TUG, where different tyres were tested on drums covered with PERS, and later field tests were made on a local street in Sweden where VTI had constructed a 25 m long trial section. The field tests were made with a CPX trailer from TUG. Both laboratory and field results showed that tyre/road noise reductions of 9-11 dB were achieved compared to a dense asphalt concrete pavement with maximum aggregate size 11 mm. This is the best result so far in the project. At the same time, this PERS, despite being relatively soft, reduces rolling resistance of passenger car tyres to record-low values, which is important for reducing fuel consumption and CO2 emissions. It is concluded that this type of prefabricated poroelastic road surface offers a very efficient way of reducing tyre/road noise, provided current durability problems can be solved.
Full Paper
Innovative low noise surfaces - comparison of damping and absorption
Freitas, Elisabete Fraga (1), Dias Rodrigues, José (2), Araújo, Jorge (1), Silva, Hugo (1)
(1) University of Minho, Portugal
(2) University of Porto, Portugal
ABSTRACT
While sound absorption is an acoustic related property reasonably well known and currently used to characterize low noise surfaces, damping is a property commonly used in other domains to define the energy dissipation of a material but rarely used to characterize this important mechanism in road pavements. This paper compares noise related properties such as damping and absorption of five road pavement surfaces. Two of which are innovative and therefore expected to be low noise since they have high voids content, incorporate fine grading aggregates and expanded clay. Other two incorporate rubber and waste high-density polyethylene giving them an elastic and stiff behaviour respectively. The fifth is a conventional material, asphalt concrete, used for control. Sound absorption tests and mechanical impedance tests were carried out in 30x30 cm slabs at 20oC. To measure absorption, an impedance tube with an open end was put on the surfaces. To determine damping, the response of a hammer impact measured by an accelerometer on suspended slabs was analysed. Results show that the innovative surfaces have better acoustic related properties while the surface with high-density polyethylene provided the worst results. Furthermore, a strong correlation of damping and air voids was found.
Full Paper
Developing a durable and ultra low noise poroelastic pavement
Goubert, Luc
Belgian Road Research Centre, Belgium
ABSTRACT
Affordable and effective traffic noise mitigation measures are highly wanted, e.g. for the "action plans" which are due for the European Noise Directive in the EU MS. Low noise pavements are an interesting option as they are a "source measure" and relatively cheap compared to other measures. The problem with the conventional low noise pavements is that the obtained noise reduction (typical 2 to 7 dBA) is lower than what can be achieved with noise barriers (typical 7 up to 12 dBA). A poroelastic road surface (PERS), consisting of a significant amount of rubber and bound with an elastic polymer, such as polyurethane, has proven to be capable of reducing the tyre/road noise with 8 to 12 dBA. A limited durability was one of the major obstacles for its use. Since 2009 a consortium of twelve EU partners is working on the development of a useable type of PERS in the EU funded PERSUADE project. All relevant aspects are being considered and for all remaining problems one tried to find a solution. Mixes which at least perform well in the laboratory have been found and these are currently tested on road test tracks. This paper summarizes the current project status.
Full Paper
The best porous asphalt pavement in Sweden so far
Sandberg, Ulf (1), Mioduszewski, Piotr (2)
(1) Swedish National Road and Transport Research Institute, Sweden
(2) Gdansk University of Technology, Poland
ABSTRACT
In 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high initial reduction but due to the widespread use of studded tyres in winter, clogging and ravelling created a loss of around 2 dB per year, with an acoustical lifetime of only 3 years.
However, the improved pavement in Huskvarna has exceeded lifetime and durability expectations by at least 100 %. The first three years noise reduction fell from the initial 7-8 dB by about 1 dB, compared to an SMA 16 pavement, and now in its 4th year the main pavement still performs well.
This paper presents results of noise measurements over a 4-year period on various versions of the DPAC and single-layer porous asphalt which were tried at the site. This includes the effects of grinding, cleaning, and rejuvenation. Measurements were made by TUG using the CPX method and two reference tyres.
Full Paper
Overview of existing Noise Mitigation Systems for reducing Pile-Driving Noise
Bellmann, Michael
itap GmbH, Germany
ABSTRACT
Underwater noise caused by impulse pile-driving during the installation of offshore foundations is potentially harmful to marine life, especially marine mammals. In Germany the regulation authority (BSH) set following limit values: (i) Sound Exposure Level (SEL) = 160 dB (re 1 µ Pa2s) and (ii) Peak Level (LPeak) = 190 dB (re 1 µ Pa) which must be complied with at a distance of 750 m to the construction site. The experience over the last years shows that underwater sound during pile-driving mainly depends on pile diameter (currently up to 6.5 m) and the blow energy used. Measurements show values of up to 180 dB for the SEL and up to 205 dB for the LPeak. Therefore, Noise Mitigation Systems (NMS) are necessary to minimize the underwater noise significantly. Since 2011 NMSs have to be applied during noisy construction work at all OWFs in Germany. The itap measured the underwater noise and evaluated the sound reduction due to the NMS used during nine OWF construction phases and several substations as well as transformer platform installations. Additionally, itap was involved in many funded research projects dealing with the evaluation and enhancement of existing NMS like OFF BW II. Overall, more than 700 piles were installed in the German North and Baltic Sea by using different NMS in different system configurations over the last years. In this paper a general overview of existing and tested noise mitigation systems is given. The main results and general findings regarding the factors that influence noise reduction will be discussed. Finally, it will be discussed if a general State-of-the-Art exists regarding noise reduction and NMS from the acoustical point of view.
Full Paper
The new noise mitigation system \'Hydro Sound Dampers\': history of development with several hydro sound and vibration measurements
Bruns, Benedikt (1), Kuhn, Christian (1), Stein, Philipp (1), Gattermann, Jörg (1), Elmer, Karl-Heinz (2)
(1) Technische Universität Braunschweig, Germany
(2) For some years, a noise prevention concept for the protection of marine animals exists in Germany. Based on that, the underwater sound exposure level SEL due to pile driving at offshore wind farms OWF is required to be less than 160 dB re 1 µPa2s at a distance of 750 m. This value, however, is often exceeded so that the use of a soundproofing system is necessary. The Hydro Sound Damper HSD is a new, versatile method to reduce noise levels during offshore pile driving. To achieve this, elements of different sizes and materials which are fixed to fishing nets are used. The principle of operation and the effectiveness of these HSD elements were investigated in the laboratory and in situ under offshore conditions during different pile installations. During these offshore applications thorough measurements were performed which metered the propagation of the hydro sound and the vibrations of the sea floor at various distances and directions from the source. The evaluation of these data led to very promising results concerning underwater noise reduction. This article describes the theory and implementation of the HSD and focuses on the interpretation of the data from the hydro sound and vibration measurements.
ABSTRACT
For some years, a noise prevention concept for the protection of marine animals exists in Germany. Based on that, the underwater sound exposure level (SEL) due to pile driving at offshore wind farms (OWF) is required to be less than 160 dB re 1 µPa2s at a distance of 750 m. This value, however, is often exceeded so that the use of a soundproofing system is necessary. The Hydro Sound Damper (HSD) is a new, versatile method to reduce noise levels during offshore pile driving. To achieve this, elements of different sizes and materials which are fixed to fishing nets are used. The principle of operation and the effectiveness of these HSD elements were investigated in the laboratory and in situ under offshore conditions during different pile installations. During these offshore applications thorough measurements were performed which metered the propagation of the hydro sound and the vibrations of the sea floor at various distances and directions from the source. The evaluation of these data led to very promising results concerning underwater noise reduction. This article describes the theory and implementation of the HSD and focuses on the interpretation of the data from the hydro sound and vibration measurements.
Full Paper
Analytical model for the sound pressure waveform radiated underwater when an offshore steel pipe pile is driven with an impact hammer
Hall, Marshall V
Marshall Hall Acoustics, Australia
ABSTRACT
An analytical model has been developed for the pressure waveform radiated underwater when an offshore steel pipe pile is struck by a hammer. The model is based on the coupled equations of motion for axial and radial vibration of a thin shell and yields frequency-dependent phase velocity and attenuation of these vibrations. A harmonic solution is obtained for the radiated sound pressure, using Junger and Feit's "Transform formulation of the pressure field of cylindrical radiators", which uses a Fourier Transform over vertical wavenumber. The model is applied to a comprehensively described measurement of a 6-tonne hammer driving a pile 32 m long and 76-cm in diameter. The pressure waveforms at horizontal range 12 m are examined at two mid-water hydrophone depths. The correlations between the model waveforms and the measured waveforms are high. For the main positive and negative peaks, the present model yields an average Peak-SPL of 219 dB re 1 µPa, which is 2 dB higher than the average of the corresponding measurements. Possible causes of this small difference are discussed.
Full Paper
Caltrans compendium of underwater sound data from pile driving - 2014 update
Rodkin, Richard (1), Pommerenck, Keith (1)
(1) Illingworth & Rodkin, Inc., USA
ABSTRACT
In 2009 the California Department of Transportation (Caltrans) published Technical Guidance for Assessment and Mitigation of Hydroacoustic Effects of Pile Driving on Fish (1). The purpose of the technical manual is to provide Caltrans engineers and biologists, and consultants with guidance related to the environmental permitting of pile driving projects in or near water. Appendix I - Compendium of Pile Driving Sound Data provides a summary of measured underwater sound levels for a variety of pile driving situations. The Compendium originally summarized and reported data from 36 projects between years 2000 - 2006. The Compendium was updated in 2012 with addition of 21 projects and updated again in 2014 with the addition of new data from 12 projects. The projects added in 2012 and 2014 included various types of pile driving for coastal and river bridges, harbors and wharfs, additional construction of the San Francisco - Oakland Bay Bridge, and a major structure over water being built for the US Navy. This paper highlights several interesting projects and updates analyses of the data base.
Full Paper
New achievements in underwater noise modelling for offshore pile driving
Trimoreau, Benjamin (1), Smidt Lützen, René (1), Vindahl Kringelum, Jon (2), Shajarati, Amir (2), Skjellerup, Peter (3)
(1) Lloyd\'s Register Consulting, Denmark
(2) DONG Energy Wind Power, Denmark
(3) Geocos, Denmark
ABSTRACT
Underwater noise emission from pile driving within the offshore wind industry is becoming an increasingly important issue. To advance the understanding and ability to predict underwater noise emissions and associated control measures, Lloyd's Register Consulting and DONG Energy Wind Power have initiated model development activities. Two procedures have been applied. First a technique based on empirical data and long range sound transmission models was successfully evaluated. The prediction is based on a semi-empirical source strength which may be re-used for another site, provided the piling setup is similar. Second, a modelling method was then initiated to account for any hammer and pile configurations and gain knowledge on the near-field sound generation. The method combines two techniques: stress-Wave Equation Analysis for Piles (WEAP) and vibro-acoustic Finite Element (FE). WEAP is a well-established geotechnical tool that calculates the stress wave in the hammer-pile system. A customized WEAP is implemented in order to output soil damping and loading function information. The time-domain FE model is then set up accordingly and predicts acoustic pressure data in the vicinity of the pile. Comparisons to measured hydrophone data are very promising and that bodes well for the next modelling steps.
Full Paper
A comparison of numerical methods for the time domain modelling of pile driving noise in the near field
Wilkes, Daniel Ryan (1), Gourlay, Tim (1), Gavrilov, Alexander N (1)
(1) Curtin University, Australia
ABSTRACT
This paper presents a comparison of numerical methods for the modelling of pile driving noise in the near field of the pile. The numerical models considered consist of (1) an axisymmetric time domain finite difference method (FDM), developed by the Centre for Marine Science and Technology in the Matlab programming language, and (2) an axisymmetric time domain finite element method (FEM), which is available as part of the PAFEC-FE commercial software suite. The FDM employs thin-shell theory to model the cylindrical steel pile and the acoustic wave equation to model the water and fluid seabed, while the FEM employs the elastic and acoustic wave equations to model sound propagation in the pile and water/fluid seabed respectively. A one-way coupling of the pile displacements to the fluid pressures is utilised in the FDM to model the acoustic radiation from the pile excitation, while the FEM employs a fully coupled fluid-structure interaction at the solid-fluid interface. Numerical results for both models are presented in the form of pile radial displacement results and pressure results in the near field of the pile. Good agreement is observed between the FDM and FEM models, while the FDM is observed to be at least twice as fast as the FEM for the considered models.
Full Paper
WYSAHIWYG (What You See And Hear Is What You Get): Learning from photocartography in mapping the cross-modal features of the soundscape
Carter, J Parkman (1), Braasch, Jonas (1)
(1) Rensselaer Polytechnic Institute, USA
ABSTRACT
"Measuring" the soundscape is like trying to measure the ocean, the forest, or the city—one dimensional metrics and color-coded maps are inadequate to meaningfully describe the myriad complex conditions, relationships, and effects which comprise the soundscape's impact upon us, and our impact upon it. In order to better understand the subjective experience of the soundscape, we need new methods to capture and represent the multisensory extents of the sonic environment. Much can be learned from the recent revolution in photocartography—which uses various forms of satellite and street view photography to generate interactive online maps. Photocartography is the new WYSIWYG (What You See Is What You Get) interface, and has rapidly proven to be more data-rich and more broadly accessible than conventional symbolic maps. This project proposes an interdisciplinary method to integrate multi-directional Ambisonic audio recordings of an environment with high dynamic range (HDR) spherical panoramic photography in the form of interactive maps and virtual tours. Case studies from both urban and park environments will demonstrate how this cross-modal mapping method can capture and reveal specific soundscape phenomena which elude conventional acoustic measurements.
Full Paper
Aures - The Advanced Environment Noise Monitoring System - Leq(A) or new measurement technology?
Leskinen, Antti (1), Hjort, Roy (2), Saine, Kari (3), Gao, Zengxin (3)
(1) APL Systems Oy, Finland
(2) APL Systems Oy, Finland
(3) Wärtsilä Finland Oy, Finland
ABSTRACT
Noise has become one of the major environmental pollutions in urban areas. To ensure that the environmental noise requirements are fulfilled, the noise emission from industries must stay within allowable limits under normal operating conditions. APL Systems has developed an automatic noise surveillance system "Aures" in close cooperation with Wärtsilä Finland. The system includes Aures 2.0 -units and a server operating the Aures Analyzer -software. The possibility of long-term recording and analysing the surrounding noise in frequency domain has enabled this application to be one of the best available environmental noise surveillance systems in the market. The technology of frequency domain measurement and analysis has made it possible to understand better the components of certain noise source. With this feature, it is also possible to get more reliable measurement data when comparing to calculations. This paper questions present environmental legislation it's compatibility with the present needs of the different stakeholders including industry and public authorities. The paper also discusses presenting noise data in frequency domain instead of overall levels and especially why it should done so.
Full Paper
WithdrawnB
WithdrawnB,
ABSTRACT
WithdrawnB
QUADMAP, three pilots and a methodology
Wolfert, Henk
DCMR EPA, Netherlands
ABSTRACT
QUADMAP a LIFE+ project is running in three European cities, Bilbao, Florence and Rotterdam. The project
aims to develop a methodology for identification, selection and management of quiet urban areas (QUA's).
This because a methodology is still lacking. In the pilot various types of Quiet Urban Areas have been studied. The areas were analyzed by means of noise mapping, noise measurements and field surveys, asking visitors to their perception. An expert judgment was also conducted. Based upon these analyses interventions were proposed for the selected areas in order to improve the current soundscape, and the overall perception and valuation of the visitors of these areas. The aim of designating and protecting Quiet Urban Areas is that areas with a good acoustic quality and relatively low noise levels are beneficial for health because it offers relaxation and reduce stress levels. Some results are already available on the noise levels determined, perception of wellbeing and all kind of elements present in these areas. Interventions have been planned and employed. The QUADMAP pilot projects will comprise an ex-ante evaluation as well, giving more insight on the effects of various interventions such as noise barriers, low noise asphalt and nature features, on both acoustic and perception factors.
Full Paper
Ground-borne vibrations, sounds and secondary airborne sounds from tramways: a psychoacoustic evaluation including health aspects
Cik, Michael (1), Lercher, Peter (2)
(1) University of Technology, Graz, Austria
(2) Medical University Innsbruck, Austria
ABSTRACT
For decades, urban noise and vibration studies were mostly concerned with road traffic and trains. Tramway noise was rarely studied. Since the introduction of new types of tramways in the city of Graz strong complaints were brought up by local residents in certain areas. Typically, the annoyance by tramways results from a complex combination of sounds and vibration exposure depending on ground structure and building conditions. To sufficiently account for this complexity an integrated psychoacoustic approach was applied. In a free field study ground-borne vibrations and sounds as well as secondary airborne sound recordings were carried out for various tramway types. For this purpose a binaural dummy head measurement system for noise and a triaxial accelerometer for vibrations were used to operate in synchrony. In addition to standard sound parameters (SPL), psychoacoustic parameters were analyzed to learn more about the complex psychological and physiological responses associated with the introduction of the new tramway types in Graz. First results indicate differences between the different tramway types in both classical and psychoacoustic indicators. Preliminary analyses show slightly higher levels of loudness and roughness for the new tram pass-bys while mean vibration levels stay below the typical threshold values for the average human subject.
Full Paper
Psychoacoustic experiments on some unwanted interior car sounds
Fastl, Hugo (1), Beidenhauser, Georg (1)
(1) Technische Universität München, Germany
ABSTRACT
Unwanted components of car interior sounds include rattling, creaking, squeaking etc. which ideally should be inaudible. On the other hand, wanted sounds which convey information like the click of a switch should be audible also at typical driving speeds. Therefore, in psychoacoustic experiments the audibility of both unwanted and wanted sounds were studied in silence as well as in background noise typical for premium cars at driving speeds of 50 km/h or 120 km/h. In addition, 1/3-oct-band spectra were measured of all evaluated sounds in view of possible predictions of their audibility. The present pilot study features results of psychoacoustic studies on the audibility of unwanted and wanted interior car sounds and gives guidelines towards related algorithmic predictions. Approaches based on spectral displays like Zwicker's excitation pattern model or loudness patterns seem to be rather promising.
Full Paper
Continuous judgment of sound quality of electric home appliances
Kuwano, Sonoko (1), Namba, Seiichiro (1), Fastl, Hugo (2), Putner, Jakob (2)
(1) Osaka University, Japan
(2) Technische Universitaet Muenchen, Germany
ABSTRACT
The sound quality of machinery noises is multi-dimensional and is often examined using semantic differential. In this case the overall impression of sound quality is judged. However, sound quality may vary according to the temporal stream of sounds. In this study, sound quality of electric home appliances was judged using the continuous judgment by line length. Forty-one kinds of the sound of home electric appliances were connected in random sequences with a slight interval between the sounds. The original sounds and their modified sounds were included in the stimulus of 8 min. The experiment was conducted in Technische Universiät München. Ten German participants joined the experiment. They conducted three sessions in which they judged the instantaneous impression of loudness, sharpness and unpleasantness, respectively. The subjective responses were sampled every 100ms. The values of every 100ms of LAeq, LLz(p), calculated sharpness and comfort index (CI) were measured. As a whole the physical metrics showed good correlation with subjective judgments. On the other hand, when the relation between physical metrics and subjective judgments was examined in a limited portion, different tendency was found. It would be better to examine the sound quality along the temporal stream in detail in order to find the clues to improve the sound quality.
Full Paper
The comparison of psychological evaluation
between military aircraft noise and civil aircraft noise
Morinaga, Makoto (1), Yamamoto, Ippei (1), Tsukioka, Hidebumi (1), Makino, Koichi (2), Kuwano, Sonoko (3), Matsumoto, Mitsuo (4)
(1) Defense Facilities Environment Improvement Association, Japan
(2) Kobayasi Institute of Physical Research, Japan
(3) Osaka University, Japan
(4) Japan Ministry of Defense, Japan
ABSTRACT
It is reported that community response to military aircraft noise is severer than that to civil aircraft noise in some former studies. In the present study, psychological experiments were conducted including the stimuli of military aircraft noise and civil aircraft noise. Participants were not informed whether each noise source was a military or civil aircraft. It was found that perceived noisiness and subjective annoyance to aircraft noises were almost the same between noises from military and civil aircraft when single-event, A-weighted sound exposure levels were equal. This suggests that participants did not distinguish between military and civil aircraft noise. These results imply that overestimation of military aircraft noise is caused by not only acoustic properties but also non-acoustic factors, such as attitude toward military aircraft noise.
Full Paper
ISO 532 - Living and working with alternative loudness standards
Scheuren, Joachim
Müller-BBM, Germany
ABSTRACT
By its very nature, standardization claims to set unique rules and procedures, thus aiming unique, i.e. comparable and reproducible results. Also, to be effective, the standard and the underlying approach need to be broadly accepted by the addressed user community. To come up with such general agreement it is typically required that a "best" approach, covering all relevant applications of interest, has been established. If this does not apply, the existence of alternative standards in parallel may offer a way out.
The revision process of ISO 532 "Acoustics - Methods for calculating loudness" showed that it was not possible to prove and agree on a single "best" approach. Acknowledging the legitimate demand of applicative continuity, the member bodies of ISO TC 43 "Acoustics" therefore decided to maintain the given situation by specifying two alternative approaches again. With reference to existing national standards (DIN 45631/A1 and ANSI S3.4), these are the Zwicker approach in an extended version for time-varying sounds and the Moore/Glasberg approach for stationary sounds at first.
Based on a review of the revision process and a summarizing justification of the resulting decision, the discussion of practical and theoretical consequences of the renewed dualism will outline the chances for broader applications of loudness calculations. However, this dualism also establishes the commitment to thoroughly identify and seize the chance for final unification of the standard.
Full Paper
Overall loudness of short time-varying sounds
Schlittenlacher, Josef (1), Hashimoto, Takeo (2), Kuwano, Sonoko (3), Namba, Seiichiro (3)
(1) TU Darmstadt, Germany
(2) Seikei University, Japan
(3) Osaka University, Japan
ABSTRACT
When predicting the overall loudness of time-varying sounds, it is necessary to use a function which calculates an overall value based on instantaneous loudness. Although N5 and LL(P) correlate for many sounds, their concepts are rather different. N5 is the loudness which is exceeded in five percent of the time, thus it is an ordinal value. LL(P) is the energetic mean of all instantaneous loudness values. For the present set of experiments, sounds with orthogonal conditions were chosen. This means they vary in N5 in a dynamic range of about 30 phon but have constant loudness according to LL(P) or vice versa. Participants judged the overall and instantaneous loudness of the sounds with ten seconds duration by magnitude estimation using line length and continuous judgment. The results show that LL(P) has some advantages compared to N5. In contrast to N5, it correlates highly with the overall loudness for the present set of stimuli.
Full Paper
Measurement of air-conducted and bone-conducted dental drilling sounds
Yamada, Tomomi (1), Kuwano, Sonoko (1), Yasuno, Yoshinobu (2), Kaku, Jiro (2), Ebisu, Shigeyuki (1), Hayashi, Mikako (1)
(1) Osaka University, Japan
(2) Kobayasi Institute of Physical Research, Japan
ABSTRACT
Patients in dental clinics perceive the bone-conducted sound via the teeth in addition to the air-conducted sound from the ear during the drilling of their teeth. In order to reduce the discomfort during treatment, it is necessary to find the characteristics of both the air-conducted and the bone-conducted dental drilling sounds. It was found in our former studies that rich high-frequency components up to 20 kHz are included in the air-conducted dental drilling sound. However the characteristic of the bone-conducted dental drilling sound is not well known. In this study, the air-conducted and the bone-conducted dental drilling sounds up to high frequency range were simultaneously measured by microphones placed near the participants and on the participants' foreheads during drilling dental materials covered on their teeth. Further, the bone-conducted sound was measured during the drilling of the artificial teeth on the measurement model using the twelve kinds of dental drills. As the result, high frequency components up to 20 kHz in the bone-conducted dental drilling sound were observed.
Full Paper
Noise annoyance for a motorway compared to urban roads
Bendtsen, Hans (1), Pedersen, Torben Holm (2), Le Ray, Guillaume (2), Kragh, Jørgen (1)
(1) Danish Road Directorate, Denmark
(2) DELTA SenseLab, Denmark
ABSTRACT
This study summarizes of the noise annoyance from road traffic noise from a motorway (M3) and two urban roads near Copenhagen. The urban roads are characterized by open urban areas with a substantial share of 3-5 storeyed residences (2870 respondents). The areas next to motorway M3 consisted mainly of 1-2 storeyed houses protected by noise barriers of 4 m height along the motorway (1410 respondents). At noise exposure levels, Lden, below approx. 55 dB the dose-response curves were not significantly different. At noise exposures above 55-58 dB the noise from the M3 is perceived as more annoying than the noise of urban roads at the same levels. At the high levels, this difference is equivalent to a difference of approximately 5 dB. The annoyance around the M3 motorway is significantly and substantially above the annoyance found in the European dose-response curves. The M3 study shows that at 50% annoyed the neighbours are so much more annoyed that it equivalent to 6-12 dB higher noise exposures. For the urban roads it was found that at 50% annoyed the annoyance compared the European curves was equivalent to 3-5 dB higher noise exposure.
Full Paper
Using mathematical models to predict annoyance from combined noise sources in the city of Dubai
Elmedhi, Hussein
University of Sharjah, United Arab Emirates
ABSTRACT
Residents of major cities of the United Arab Emirates are exposed to multiple noise sources originating from road traffic, aircraft flyovers and various industrial activities. Predicting the contribution of each of these sources to public annoyance, and hence relating it to health effects on residents of these cities, is not an easy task because of the complex nature of these sources and their subjective contribution to community annoyance. In this paper, we report preliminary results of applying mathematical models to assess annoyance due to combined sources using data obtained from noise level measurements in combination with social surveys conducted near the selected sites. The models are based on the 24-h average sound levels LAeq, 24h and the measured annoyance scores for aircraft, road traffic, and combined noise. Models are based on the assumption that the annoyance caused by combined noise sources can be predicted by the total energy and separate sources make independent contributions to the total annoyance. Our results show that annoyance due to aircraft noise was slightly modified by additional road traffic noise. The results also indicate that road traffic noise exposure and annoyance were more dominant than those of aircraft noise at most sites.
Full Paper
The influence of location of the privileged vehicle siren on the vehicle traffic safety
Gorski, Pawel (1), Zawieska, Wiktor M (1)
(1) Central Institute for Labour Protection - NRI, Poland
ABSTRACT
Audible emergency signals generated by sirens of privileged vehicles should be audible and recognisable by all participants of the traffic. Currently in Poland, A-weighted sound pressure levels of audible emergency signals generated by sirens of privileged vehicles range between 104 and 108 dB. In turn, the A-weighted sound pressure levels measured inside the privileged vehicles may exceed the value of 90dB. Such high sound pressure levels may adversely affect the working conditions of the privileged vehicle crew. A commonly applied solution, aimed at limiting the exposure of the privileged vehicle crew to noise, is fitting the siren in the engine compartment rather than in the vehicle roof lightbar. Changing the location of the siren can reduce the measured sound pressure levels inside the vehicles by about 10 dB. Changing the location of the siren has also a significant impact on the audibility of the emergency signal by the other participants of the road, and thus affects the vehicle traffic safety. It is necessary to initiate a discussion on improving the acoustic comfort of the vehicle crew, and at the same time maintain the informational function of the emergency signals.
Full Paper
Structural equation model of road traffic noise annoyance in Vietnam
Nguyen, Thu Lan (1), Yano, Takashi (1), Yokoshima, Shigenori (2), Morihara, Takashi (3)
(1) Kumamoto University, Japan
(2) Kanagawa Environmental Research Center, Japan
(3) Ishikawa National College of Technology, Japan
ABSTRACT
The exposure-response relationships for road traffic noise annoyance in Vietnam were proposed according to over 4700 responses obtained in Hanoi, Ho Chi Minh, Da Nang, Hue and Thai Nguyen. However, the variation of the exposure-response curves found among the five cities implied that discrepancies could occur between different geographic regions like the north and the south of Vietnam. To assess the effects of acoustic and non-acoustic factors on road traffic noise annoyance in Vietnam, structural equation models were developed by linking the questionnaire items of the socio-acoustic surveys on road traffic noise annoyance conducted in the five cities. The sample sizes were 1174, 1403, 432, 592, and 633 to estimate the models for Hanoi, Ho Chi Minh, Da Nang, Hue and Thai Nguyen, respectively. The final model included three latent factors: activity interference; sensitivity; and satisfaction with living environment. Sensitivity to noise, vibration and heat are determinants of personal sensitivity. Activity interference was measured by awakening in the sleep, rest and listening disturbance. Evaluations on quietness of living areas, preference to the living areas and comfort in the dry season are loaded in satisfaction with living environment. The model provided good model fit and indicated that sensitivity and satisfaction with living environment were the main modifiers of road traffic noise annoyance in Vietnam
Full Paper
Experimental study of traffic noise and human response in an urban area: deviations from standard annoyance predictions
Salomons, Erik M (1), Janssen, Sabine A (1), Verhagen, Henk L M (1), Wessels, Peter W (1)
(1) TNO, The Netherlands
ABSTRACT
Annoyance and sleep disturbance by road and rail traffic noise in an urban area are investigated. Noise levels Lden and Lnight are determined with an engineering noise model that is optimized for the local situation, based on local noise measurements. The noise levels are combined with responses of 71 inhabitants to an annoyance survey to derive local exposure-response relations, using the regression method with censored normal distributions developed by Miedema and coworkers. It is found that the local exposure-response relations deviate considerably from the 'standard' relations derived from international annoyance surveys. Noise events reported by the inhabitants - such as freight trains passing through the area at night - are described to illustrate the local situation. Future scenarios for the urban area are also analyzed, including measures aimed at reducing road and rail traffic noise. Numbers of highly-annoyed inhabitants in the urban area are calculated for different scenarios by applying the local exposure-response relations to the total population in the area of about 1000 inhabitants.
Full Paper
Social surveys on community response to road traffic in five cities in Vietnam
Shimoyama, Koji (1), Nguyen, Thu Lan (1), Yano, Takashi (1), Morihara, Takashi (2)
(1) Kumamoto University, Japan
(2) Ishikawa National College of Technology, Japan
ABSTRACT
Social surveys on community response to road traffic noise have been performed since 2005 in five major cities in Vietnam: Hanoi, Ho Chi Minh City, Da Nang, Hue and Thai Nguyen. The total sample size and the average response rate were 4966 and 64%, respectively. The noise exposures ranged from 61 to 83 dB in Lden. The exposure-response relationship was drawn with logistic regression curve based on all the socio-acoustic survey data, which can be proposed as the representative exposure-response relationship for road traffic noise in Vietnam. This curve showed that Vietnamese respondents were about 5 to 10 dB less annoyed by road traffic noise than those of EU and Japan. Exposure-response curves for general annoyance, awaking, falling asleep, conversation, telephone-listening, TV/Radio listening, reading/thinking, and rest disturbances were also drawn. Annoyance in the two largest cities, Hanoi and Ho Chi Minh City, were higher than those in the other three cities. Sleep disturbance was severer than listening and the other activity disturbances in all the cities. The distribution pattern of annoyance was consistent with those of environmental factors such as residential satisfaction. This finding suggests that noise annoyance is strongly affected by or interacted with the evaluation of residential environment.
Full Paper
Subjective experiment on auditory localization for traffic alarm sounds in a heavy truck
Yokoyama, Sakae (1), Tachibana, Hideki (2), Makinouchi, Hideo (3)
(1) Kobayasi Institute of Physical Research, Japan
(2) University of Tokyo, Japan
(3) Hino Motors, Japan
ABSTRACT
When driving a road vehicle, it is often experienced that the judgment of directions of alarm sounds like horn and sirens of ambulance car, fire engine etc. becomes difficult. Especially in case of a heavy truck, the misjudgment of auditory localization of sirens is seriously related to traffic safety, because a road can be obstructed by a heavy truck. In this study, therefore, the auditory localization for traffic alarm sounds at driver's position in a heavy truck was examined by laboratory experiments. To perform the auditory tests in an anechoic room, the 6-channel recording/reproduction system as a 3-dimensional sound field simulation technique was applied. By using measured directional impulse responses from outside into a driver's head position in a heavy truck, the source position for localization tests was distributed at every 30 degrees in horizontal plane. Further, to see the influence of a connected loading space on driver's auditory localization, the experimental investigation was performed for two cases, with/without the loading space. In this paper, the results of the localization tests are presented and acoustic problems are discussed.
Full Paper
Active noise control in practice: transformer station
Buikema, Edwin (1), Van Der Ploeg, Fokke D (1), Granneman, Jan H (1)
(1) Peutz, The Netherlands
ABSTRACT
Based on literature and extensive measurements at a specific transformer two concepts regarding anti noise have been developed. These concepts have been tested in the Peutz acoustical laboratory, and on site with an experimental setup for anti noise at large transformers. Noise measurements show that a reduction of 5 dB can be achieved in all directions. Additionally, by directing the noise emission, a reduction of 10 dB can be achieved in one specific direction. This experimental project was part of a broader demonstration project regarding the practical application of different types of sensor technology.
Full Paper
An integrated passive and active control system for reducing haul
Lin, Zhibin (1), Zhang, Limin (2), Qiu, Xiaojun (1), Pan, Jie (3)
(1) Key Laboratory of Modern Acoustics Institute of Acoustics, Nanjing University, Nanjing, China
(2) School of Electronic Science and Engineering, Nanjing University, Nanjing, China
(3) School of Mechanical & Chemical Engineering, University of Western Australia, Australia
ABSTRACT
This paper is concerned with the analysis and design of an integrated passive and active control system for reducing the haul truck noise. By using a passive enclosure with two open ends and fiberglass inner surface, a three-dimensional noise radiation problem of the engine noise is shaped to a simple problem of noise radiation from the open ends above 200 Hz. Below 200Hz where the transmission loss of the lightweight enclosure is low, a spatial global active noise control (ANC) system is constructed inside the enclosure. To improve the performance of the system, the open ends are divided into four equal diameter size ducts each followed by a louver. A single channel ANC system is set up in each duct to eliminate the noise in the frequency range from 200 Hz to 400 Hz. Experimental results demonstrate that more than 20 dB insertion loss is achieved with such a passive enclosure at frequency band above 400 Hz, and 8 dB noise reduction with global ANC systems at frequency band below 200 Hz, and 4 dB noise attenuation with single channel ANC systems between 200 Hz and 400 Hz. The results this investigation show the feasibility of hybrid noise control technique for reducing the haul truck noise.
Full Paper
A new structure for nonlinear narrowband active noise control using Volterra filter
Liu, Jian (1), Xiao, Yegui (2), Chen, Hui (1), Liu, Wenbo (1)
(1) Nanjing University of Aeronautics and Astronautics, China
(2) Prefectural University of Hiroshima, Japan
ABSTRACT
Many structures and algorithms have been developed for linear narrowband active noise control (NANC) systems, which are effective in suppressing sinusoidal noise generated by rotating machines and devices with reciprocating motion. However, the conventional linear NANC systems may seriously suffer from performance degradation due to the nonlinear distortions which, large or small, usually exist in real-life sound fields. Development of nonlinear NANC systems to solve the above-mentioned problems has recently attracted a great deal of attention and several structures and algorithms have been proposed based on the use of adaptive Volterra filter. In those systems, the sinusoidal noise at the reference point is distorted by the nonlinear part of a primary path, eventually adding some high-order harmonic components to the primary noise being targeted. But the main body of the primary noise is still dominated by linearity of the primary path. This paper presents a new structure for a nonlinear NANC system, where the largest portion of the primary noise power can be reduced by the conventional adaptive linear filter and the remaining portion due to high-order harmonics may be effectively suppressed by an adaptive Volterra filter. Numerical simulation results reveal that the proposed system is very effective in suppressing sinusoidal noise distorted by nonlinearity of the primary path.
Full Paper
Basic study on active acoustic shielding: phase 6 improving the method to enlarge AAS window-2
Murao, Tatsuya (1), Nishimura, Masaharu (1), Sakurama, Kazunori (1), Nishida, Shinichiro (1)
(1) Tottori University, Japan
ABSTRACT
In this paper, it was proved to be useful to use M[(1-1)-L'] FX-LMS algorism for Active Acoustic Shielding (AAS) window to enlarge the window size. The AAS is a system that can attenuate the sound passing though an open window. The AAS system is composed of many AAS cells set in an array. Each AAS cell consists of approximately colocated a microphone and a speaker. However, a size of existing type AAS window is 250mm square. Therefore, we proposed M[(1-1)-L'] FX-LMS algorism(M: number of AAS systems, L': number of error signals used for controlling one AAS cell) for controlling a large size window and large number of AAS cells. This algorithm is a kind of FX-LMS algorithm, each AAS cell is controlled individually by it's own reference microphone and neighboring error sensors. In the previous work, 6 AAS cells is set on rectangular window (125 x 750mm square) and controlled by 6[(1-1)-3'] FX-LMS. As a result, this system was proved to be useful for controlling AAS cells, In this paper a simulator of M[(1-1)-L'] FX-LMS algorithm was constructed, and the simulation results by 6[(1-1)-3'] FX-LMS algorithm well coincided with the above experimented results. This suggests that large AAS window feasible.
Full Paper
Virtual sound barrier for indoor transformers
Tao, Jiancheng (1), Wang, Shuping (1), Qiu, Xiaojun (1), Han, Ning (2), Zhang, Linke (3)
(1) Nanjing University, China
(2) Southeast University, China
(3) Wuhan University of Technology, China
ABSTRACT
Power transformers sometimes locate in an enclosed room with an opening surface for the ventilation purpose. Under these situations, most noise radiates out from the opening, so a virtual sound barrier can be built to suppress the sound radiation outside by employing a multiple-channel active noise control system. Based on the sound radiation model of indoor monopoles, the noise reduction performances of both centralized and decentralized control systems are investigated and compared. Considering the channel number requirement, a virtual sound barrier is built for an actual indoor transformer, where both the centralized and the decentralized strategies are investigated. Simulation results show that the fully independent virtual sound barrier is effective for the indoor transformer noise control.
Full Paper
Applying an active noise barrier on a 110 KV power transformer in Hunan
Zou, Haishan (1), Huang, Xiaofan (1), Hu, Sheng (2), Qiu, Xiaojun (1)
(1) Nanjing University, China
(2) Hunan Electric Power Corporation Research Institute, China
ABSTRACT
There are increasing needs to reduce the transformer noise recently in China because some residential buildings developed recently are located more and more close to the pre-existing substations. Passive barriers are often used around the outdoor transformers to block the noise. However, the noise reduction performance of the barriers is poor in low frequency range, especially when the noise wavelength is larger than the height of the barrier. Consequently, active noise control (ANC) system has been investigated to enhance the insertion loss of traditional barrier in low frequency. In this paper, a prototype active noise barrier (ANB) was developed and applied to a practical case. Physical system of the ANB was designed in first. Then a decentralized feedforward ANC system composed of the cascaded active units was developed, and the waterproof structures were developed to protect the elements of the system. Again, experiments were carried out on the rooftop of a five-floor building to verify the effectiveness of the system. Finally, the practical application in Hunan is investigated, in which the noise reduction of the 110kV power transformers was needed.
Full Paper
Analysis of wind turbine low frequency noise prediction accuracy
Evans, Tom (1), Cooper, Jonathan (1), Alamshah, Vahid (1)
(1) Resonate Acoustics, Australia
ABSTRACT
Some regulatory authorities in Australia have recently proposed low frequency noise assessment criteria for wind farms based on C-weighted noise levels. This involves the specification of an outdoor night time trigger level of 60 dB(C), above which further investigation may be required. While the accuracy of noise model predictions of A-weighted noise levels is well established for wind turbines, less information is available on the accuracy of low frequency noise predictions. This paper presents an analysis of approximately eight months of low frequency noise measurements at a location near a wind farm, conducted using appropriate windshields and at locations away from extraneous noise sources. The measured low frequency noise levels are compared to predicted levels to assess the accuracy of conventional noise modelling techniques for low frequency wind farm noise. Changes in low frequency noise levels with wind direction, wind speed and wind shear are also analysed.
Full Paper
Comparison of the noise levels measured in the vicinity of a wind farm for shutdown and operational conditions
Hansen, Kristy (1), Zajamsek, Branko (1), Hansen, Colin (1)
(1) Adelaide University, Australia
ABSTRACT
Outdoor and indoor microphone measurements have been taken in the vicinity of the Waterloo wind farm at a number of locations during periods when the nearby wind farm was operational as well as when it was shutdown. The majority of the shutdowns were of short duration and deliberate on the part of the wind farm operator, as they were associated with the recent EPA noise impact study. However, one of the shutdowns lasted for several days as it was related to a cable fault. Comparisons are made between both the third-octave spectra and narrowband spectra measured during the shutdown and operational periods. Operational times immediately adjacent to the shutdown times, as well as at other times when the wind conditions at hub height and at the residence matched the conditions recorded during a shutdown time, are considered in the analysis. It is shown that there are consistent and significant differences in noise spectra at the residence for the shutdown and operational cases, particularly for frequencies below 100 Hz. These differences can be observed at distances up to 8.7 km from the wind farm.
Full Paper
Infrasound and blade pass frequency levels in areas adjacent to wind farms
Lenchine, Valeri V (1), Song, Jonathan (1)
(1) SA Environment Protection Authority, Australia
ABSTRACT
Concerns have been expressed by sections of surrounding community about infrasound produced by wind farm renewable energy facilities from specific nearby wind farm locations in Australia. This has received regular media attention. There are various methods which can be used to determine the contribution of infrasound by wind farm facilities. However sometimes they do not produce conclusive results. This paper discusses the use of statistical hypothesis tests to determine infrasound contributions of wind farms. Verification of equivalency of means and equivalency of variance hypotheses were used on several shutdown and similar operational periods to check for infrasound impact. The data sets were collected during infrasound measurements performed at 3 different locations with a distance range of approximately 1.3km to 3.5km. Results show that the wind farms tested can contribute to infrasound at large distances but levels were significantly lower than the conservative perception threshold of 85dB(G). The blade pass frequencies were also analysed for the same set of data to detect any potential to exacerbate human perception of infrasound. It was found that the blade pass frequency was not very prominent at all monitoring locations and was detected at levels significantly below the perception threshold. There was also a minimal difference in blade pass frequency magnitudes and its prominency for indoors and outdoors measurements. In general infrasound impact from modern turbines at the distant receivers cannot be considered excessive and its magnitudes are significantly below the perception threshold.
Full Paper
Propagation thresholds and measurement of infrasound to establish separation distances from wind farm turbines to residences
Thorne, Bob
Noise Measurement Services Pty Ltd, Brisbane, Australia
ABSTRACT
Of all the issues surrounding noise emissions from wind farms, the question of the potential for annoyance and adverse effects from low frequency sound is one of the most topical. Anecdotal literature is replete with statements concerning the effects of infrasound and low frequency noise. In this paper we present objective methodologies to measure and assess infrasound and low frequency noise in the context of wind farm emissions. The methodologies are reviewed with respect to three wind farms: one each in New Zealand, Victoria (Australia) and South Australia. The South Australian review incorporates data from a recent South Australian EPA wind farm study. The calculations for recommended stand-off distances from wind turbines to residences are presented. The distances are based on the threshold of annoyance and physiological effects threshold anticipated for different turbines and frequencies.
Full Paper
Investigation of the time dependent nature of infrasound measured near a wind farm
Zajamsek, Branko (1), Hansen, Kristy (1), Hansen, Colin (1)
(1) University of Adelaide, Australia
ABSTRACT
It is well-known that wind farm noise is dominated by low-frequency energy at large distances from the wind farm, where the high frequency noise has been more attenuated than low-frequency noise. It has also been found that wind farm noise is highly variable with time due to the influence of atmospheric factors such as atmospheric turbulence, wake turbulence from upstream turbines and wind shear, as well as effects that can be attributed to blade rotation. Nevertheless, many standards that are used to determine wind farm compliance are based on overall A-weighted levels which have been averaged over a period of time. Therefore the aim of the work described in this paper is to investigate the time dependent nature of unweighted wind farm noise and its perceptibility, with a focus on infrasound. Measurements were carried out during shutdown and operational conditions and results show that wind farm infrasound could be detectable by the human ear although not perceived as sound.
Full Paper
Sound source localisation using a single acoustic vector sensor and multichannel microphone phased arrays
Jing, Wen-Qian (1), Fernandez Comesaña, Daniel (2), Perez Cabo, David (2)
(1) Microflown Technologies, The Netherlands, Hefei University of Technology, China
(2) Microflown Technologies, The Netherlands
ABSTRACT
In recent years, there has been growing interest in the development of noise prediction and reduction techniques. The ability to localise problematic sound sources and determine their contribution to the overall perceived sound provides an excellent first step towards reducing noise. Several well-known methods can be applied in order to achieve a detailed acoustic assessment using microphone phased arrays. However, pressure-based solutions encounter difficulties assessing low frequency problems and their performance is often limited by spatial coherence losses. Alternatively, the use of acoustic vector sensor (AVS) offers several advantages in such conditions due to their vector nature. Each AVS is comprised of a pressure microphone and three orthogonal particle velocity sensors, allowing for the sound direction of arrival to be determined at any frequency within the audible frequency range. Sound localisation techniques using AVS are evaluated in this paper, comparing the characteristics of this innovative solution with respect to traditional microphone phased arrays.
Full Paper
Identification of acoustic event of selected noise sources in a long-term environmental monitoring systems
Klaczynski, Maciej (1), Wszolek, Tadeusz (1), Cioch, Witold (1), Wszolek, Wieslaw (1), Pawlik, Pawel (1), Mleczko, Dominik (1), Grzeczka, Anna (2)
(1) AGH University of Science And Technology, Poland
(2) Gdansk University of Technology, Poland
ABSTRACT
Undertaking long-term acoustic measurements on sites located near an airport is related to a problem of large quantities of recorded data, which very often represents information not related to flight operations. In such areas, usually defined as zone of limited use, often other sources of noise exist, such as roads or railway lines treated is such context as acoustic background. Manual verification of such recorded data is a costly and time-consuming process. However, the use of special systems or devices that support the recognition of noise sources is an additional high cost. Thus, the said problems bring up an idea to use automated methods to identify noise sources and time of such events. The proposed solution is to use pattern recognition techniques for acoustic signal recorded by the monitoring station, without the need for additional equipment. Methods based on an automatic "meaning" of sounds recorded by measuring microphone (included monitoring station) and refer to the advanced techniques of cognitive referring to the human auditory perception. In this way will be possible to assign markers to acoustic events and calculate an acoustic indicator of environmental assessment. The recordings from the stations of long-term acoustics monitoring have been used while classifying the traffic noise - aircraft operations, movement of trains or cars.
Full Paper
Aeroacoustic time-reversal in the presence of a reflecting surface
Mimani, Akhilesh (1), Doolan, Con J (1), Medwell, Paul R (1)
(1) The University of Adelaide, Australia
ABSTRACT
The influence of a rigid-wall reflecting surface on aeroacoustic Time-Reversal (TR) is investigated in this work. To this end, a forward simulation of a Gaussian pulse propagation in 2-D computational domain with a uniform mean flow was implemented by numerically solving the Linearised Euler Equations subject to a rigid-wall condition (by setting the normal velocity to zero) at the bottom boundary modelling the reflecting condition. The anechoic conditions were implemented at the remaining three boundaries, thereby modelling a semi-infinite 2-D free-space. The acoustic pressure time-history was stored at all boundaries during the forward simulation. A set of TR simulations were carried out wherein rigid-wall condition was implemented at bottom boundary in each of the test-cases and time-reversed acoustic pressure was enforced at (1) all four boundaries, (2) three boundaries excluding the bottom boundary, (3) the top and bottom boundaries and (4) only the top boundary in the first, second, third and fourth test-case, respectively. It was observed that the initial emission point of the pulse was accurately predicted in all four test-cases, thereby demonstrating that acoustic pressure need not be measured at the rigid-wall. Rather, taking advantage of wave-reflection, only one microphone Line Array located outside flow can be used during aeroacoustic TR for source localisation.
Full Paper
On the effect of mean flow profile, wavelength and array length on focal-resolution of a quadrupole source using aeroacoustic time-reversal
Mimani, Akhilesh (1), Doolan, Con J (1), Medwell, Paul R (1)
(1) The University of Adelaide, Australia
ABSTRACT
This paper analyses the effect of the mean flow field, source wavelength and array length on the focal-resolution characteristics of an idealised lateral quadrupole source obtained using aeroacoustic Time-Reversal (TR). The TR simulations were implemented by numerically solving the 2-D Linearised Euler Equations (LEE) and enforcing the time-reversed acoustic pressure (stored during forward simulation) at the nodes of two Line Arrays (LAs) located outside the flow and on opposite sides. The TR simulation in a stationary medium and in a uniform mean flow indicates that interaction between the converging and diverging waves in the vicinity of quadrupole focal spots perpendicular to the LAs leads to the reinforcement of acoustic power at these regions. This results in formation of side-lobes of a relative magnitude larger than the quadrupole focal spots in the source maps, thereby making it difficult to characterise a quadrupole. During TR simulation of a quadrupole in a fully-developed non-uniform shear flow, refraction of the back-propagated waves through the shear-layer forces the acoustic fluxes to be focused almost completely at the focal spots, thereby significantly improving the quadrupole focal-resolution characteristics.
Full Paper
Detection and quantification of building air infiltration using remote acoustic methods
Raman, Ganesh (1), Chelliah, Kanthasamy (1), Prakash, Manisha (1), Muehleisen, Ralph T (2)
(1) Illinois Institute of Technology, USA
(2) Argonne National Laboratory, USA
ABSTRACT
Air infiltration in residential and commercial buildings of the United States are estimated to cost approximately 23% of the total amount of heating energy used (for cooling, this estimate is approximately 14%). The aim of the current work is to apply non-intrusive acoustic techniques to detect and quantify specific envelope leaks in buildings. Noise sources associated with the leakage air flow can be localized using a compact microphone array with advanced beamforming algorithms. Also, an idea of using a synthetic acoustic source inside the building instead of pressurization of the building is discussed. Finally, attempts are made in a laboratory level to quantify leakages using the nearfield acoustic holography technique.
Full Paper
Defending workers against hearing loss: Why aren't workers hearing our message?
Elsey, Benjamin (1), Jennings, Martin (2)
(1) Hearing Conservation Australia, Australia.
(2) Department of Defence, Australia
ABSTRACT
It is well known that hearing can be damaged by noise. Noise exposure limits, engineering controls, work rotations and hearing protection are well understood and applied in the workplace; however the incidence of noise induced hearing loss continues to increase. This paper examines likely reasons why our current training of workers exposed to noise in the workplace is possibly 'falling on deaf ears'. Is the message too complicated? How can it be simplified? How can we make the hearing conservation message resonate more personally within the worker? Noise injury is currently the second biggest cost to business in general workplaces but is the number one cost for organisations supporting Defence Veterans. The human cost is also high, as shown by the diminished quality of life for the affected persons. The Australian Department of Defence has responded to this challenge by forming a 'Noise Exposure Reduction Program' taskforce charged with revamping noise and hearing conservation policies and training. This paper will showcase some of the creative yet simple techniques Defence is deploying to create more engaging training experience for servicemen and women. This is taking an important step towards changing worker's authentic engagement in personal hearing conservation.
Full Paper
Noise in the United Kingdom printing industry: then and now
Shanks, Emma
Health & Safety Laboratory, UK
ABSTRACT
Over 2 million people in the United Kingdom (UK) are exposed to potentially harmful workplace noise levels. There are about 130,000 employees in the UK printing industry many of whom have traditionally worked in noisy environments. Anecdotal evidence suggests there is a widely held belief that the issue of noise is no longer a problem in the UK printing industry. Noise measurement and exposure data from the industry, gathered by the Health & Safety Executive (HSE) in 2010 and 2011 to inform new and updated industry specific guidance, would suggest otherwise. This paper compares and discusses the noise levels in the industry around the time of the introduction of the Control of Noise at Work Regulations 2005 and the preceding Noise at Work Regulations 1989. Both sets of regulations were born of European Union Directives requiring equivalent basic laws throughout the Union on protecting workers from the risks caused by noise. The 2005 regulations introduced lower noise exposure action values than those in the 1989 regulations. The paper identifies the noisy and quiet processes at both points in time and also looks at some of the changes in the industry that have affected the noise levels and exposures.
Full Paper
Development of an Occupational Noise Exposure Reduction Project for Defence in Australia
Teague, Peter (1), Conomos, James (1), Alexandrou, Vasos (1), Jennings, Martin (2)
(1) Vipac Engineers & Scientists Ltd, Australia
(2) Department of Defence/DCOHS, Australia
ABSTRACT
Noise is the most prominent and widespread hazard to which Australian Defence Organisation (ADO) personnel are exposed. Recent advances have been made though the development of a 5 year Noise Exposure Reduction Project for occupational/workplace noise for the ADO by Vipac Engineers & Scientists Ltd. This project was informed by an initial Exposure Reduction Plan (ERP) phase that included a complete review and assessment of noise management practices across Defence and identified a range of deficiencies and recommendations for action. The ERP is based upon a continuous improvement approach and its goals are initially to ensure compliance with Work Health & Safety (WHS) legislation, then to proactively deliver minimisation of noise exposure and management of hearing loss risk throughout the whole of Defence. A coordinated and systematic approach, including best-practice noise surveys and assessments at a representative sample of Defence Bases, has provided an evidence-based dataset to inform effective noise control actions. The project and noise survey findings to date are highlighted. Tailored Noise Management Plans (NMP), with prioritised and practical noise control measures, and innovative noise management tools have been formulated to improve noise control practices across Defence.
Full Paper
Is the airborne sound power level of a source unambiguous?
Kurtz, Patrick
BAuA, Germany
ABSTRACT
Sound power levels are used as key parameters describing the noise emission of machines in the European Machinery Directive 2006/42/EC (1) and the Outdoor Equipment Directive 2000/14/EC (2). The purpose is to require machine manufacturers to provide noise emission declarations thus allowing potential purchasers to buy quiet. To support this approach for noise reduction noise emission measurement standards providing measurement methods for determining the sound power level have been constantly developed on ISO level since many years. Although the sound power level methods described in these standards are based on different concepts they claim to result in comparable sound power levels of a source when the grade of accuracy of the standard is the same. However, it is known for long that this is not really the truth. In order to get more information on this differences systematical measurements were carried out on a reference sound source using sound pressure and sound intensity discrete measurement positions as well as scanning methods on different surfaces and at different distances from the source under free-field conditions. First results of a respective EMRP project are given in this paper.
Full Paper
New York City\'s New Noise Code and NYU\'s Citygram-Sound Project
Shamoon, Charles (1), Park, Tae Hong (2)
(1) New York City, USA
(2) New York University, USA
ABSTRACT
Honk - bang - whir - whiz - roar - ding - beep - chug - boom - rattle - hum - screech - boom. More than 2000 years ago, the residents of Rome, Italy complained about the disturbing noise from chariots racing through the city's cobbled streets at night. Ever since then the sound of civilization's progress and development have led to the recognizable sounds of construction and manufacturing noise, exhausts and impact noise, horns, and sirens, etc. Also with the development of musical instruments musical sounds became an issue. Some of these sounds were welcome and some were not. Civilization's "progress" can at times seem to disturb the general tranquility of everyday life. Each observer makes the determination of the difference between "sound" and "noise." For example a perennial source of tension between parent and child is the optimal level at which music or television is enjoyed. As technology advanced so did methods to measure sound and a determination of what types of sounds created a nuisance and also at which levels noise disturbed people and effected their ability to work or rest. The City of New York is the most populous city in the United States, with its metropolitan area ranking among the largest urban areas in the world. Its size and population brings with it its own set of unique and challenging noise issues. Almost everyone enjoys certain sounds of the City. The bustle of kids playing and laughing in a park is welcome. Also welcome are the happy cheers at sporting and other public events. However, blasting stereos, honking horns, un-muffled exhausts and ear-splitting jack-hammering can ruin a good night's sleep and diminishes the city's quality of life.
Full Paper
Sound pressure level and sound power level declarations: navigating the maze
Shanks, Emma
Health & Safety Laboratory, UK
ABSTRACT
Under European law, high noise machinery supplied in Europe must be accompanied by a noise declaration. Declarations usually consist of a workstation emission sound pressure level (LpA) and, for the noisiest machines, an emission sound power level (LWA). Unexpected conflicts, confusion and inconsistencies have been observed for the declared LpA and LWA. The European NOMAD (Noise and the Machinery Directive) project reported that 80% of noise information supplied with machinery was inadequate, often because of weaknesses in the declared LWA and/or LpA. About 600 European (EN) standards contain the phrase "noise emission" and about 300 of those consider noise as a "significant hazard". The Health and Safety Laboratory (HSL) is currently investigating the practical challenges of measurement and declaration of LWA and LpA. So far, HSL has found difficulties when machines fall under multiple European Directives, when the EN standard test codes used do not provide data that represents real-use risk, or declarations that are difficult to make because the standards are ambiguous. The top priority for manufacturers is to reduce the noise emission of the machinery at source, through technical and design methods. The noise declarations should be a suitable means of verifying that this has been achieved.
Full Paper
Including atmospheric propagation effects in aircraft take-off noise modeling
Arntzen, Michael (1), Hordijk, Martijn (2), Simons, Dick G (2)
(1) NLR, The Netherlands, TU Delft, Aerospace Engineering, Aircraft Noise & Climate Effects, Netherlands
(2) TU Delft, The Netherlands
ABSTRACT
Aircraft noise is frequently calculated by models using Noise-Power-Distance relations (NPD-tables). Such an approach is common in the Integrated Noise Model (INM) or the method outlined in ECAC Doc. 29. Only a limited correction for atmospheric propagation effects is available through empirical lateral attenuation functions that are intended, as is the model, for multi-event calculations. A new feature, developed at the NLR, is to include the results of ray tracing in a Doc.29-based calculation. As such, the noise model is augmented by detailed propagation effects on a single-event level. Results are demonstrated for two different take-off procedures as Sound Exposure Level (SEL) contours. Consequently, the effects of wind on departure procedures are illustrated and further quantified by predicting awakenings in fictitious communities. The results show that the effects of sound refraction are the largest as the aircraft is low. Therefore, a departure procedure featuring a shallow climb angle shows more effects than procedure with a steeper climb. It is shown that wind effects can clearly lead to asymmetrical contours and awakenings. The results show that there is a potential for noise mitigation based on ambient atmospheric conditions.
Full Paper
Assessing all noise sources in one model. Implementation of INM and ECAC 3rd Edition in Noise Mapping Software
Notario, Antonio
DataKustik GmbH, Germany
ABSTRACT
Legal circumstances, political motivations and technical reasons led in many countries to a separated approach for the calculation, assessment and handling of infrastructure noise caused by road and railway on the one side and the analysis of aircraft noise on the other side. Specific Research efforts analyzing the perception of noise led to guidelines like the German VDI 3722 (Effects of traffic noise/Characteristic quantities in case of multiple sources). Next to other approaches this guideline focuses especially on the annoyance of different noise types and derives a single number value, representing the overall perception of all noise sources, for each affected inhabitant. In order to enable an efficient overall evaluation of noise levels within urban areas, each infrastructural source must be handled within one noise model. The implementation of INM and ECAC 3rd Edition within Noise Mapping software opens various possibilities for an integrated approach to the noise assessment within cities.
Full Paper
Practical method of considering effects of terrain and building structures on sound propagation
Yamada, Ichiro
Aviation Environment Research Center, Japan
ABSTRACT
This paper discusses practical methods of calculating adjustments for sound insertion loss due to terrain/building structures in airport noise modelling. The Japanese revised noise guideline "Environment Quality Standard for Aircraft Noise," requires sound exposure evaluation of aircraft ground activities like taxiing and using APU. This paper first makes a brief review of technical aspects of developing airport noise modeling in Japan, secondly describes the way of considering aircraft ground operation noise, thirdly discusses practical ways of calculating adjustments for sound insertion loss due to terrain/building structures and excess ground attenuation, and finally it discusses future issues. It also refers to examination of the validity of such practical ways by applying numerical calculation as well as by measurement.
Full Paper
Experimental study of meteorological and ground effects on outdoor sound propagation for developing aircraft noise prediction model
Yokota, Takatoshi (1), Makino, Koichi (1), Matsumoto, Toshio (1), Yamamoto, Kohei (1), Ishii, Hirokazu (2)
(1) Kobayasi Institute of Physical Research, Japan
(2) Japan Aerospace Exploration Agency, Japan
ABSTRACT
JAXA has been developing an aircraft noise propagation model by applying the GF-PE method. To predict aircraft noise propagation precisely, it is necessary to assume meteorological condition and ground property in the sound field appropriately. In order to study how to model those conditions in the predictions and to verify the model, outdoor sound propagation experiments were conducted in November 2012 and in July 2013 at Taiki Aerospace Research Field in Hokkaido, Japan. In the experiments, receivers were lined up on the 1000-meter long runway and on the grass-covered flat ground in the test field. An elevated sound source was hanged from a tethered balloon, while other sound sources were placed at ground level. Air-to-Ground and Ground-to-Ground impulse responses were measured under various meteorological conditions. In this paper, we introduce variations in excess attenuation due to the meteorological and ground effects. By comparing the experimental results and the calculation results of the GF-PE method, we also discuss appropriateness of the modeling of meteorological conditions and ground property in the developing aircraft noise prediction model.
Full Paper
Influence of the atmospheric stratification on the sound propagation of single flights
Zellmann, Christoph (1), Wunderli, Jean Marc (1)
(1) Empa, Switzerland
ABSTRACT
Aircraft noise models generally simplify the atmosphere as homogenous and constant over time. However, momentary local conditions of wind, humidity and temperature influence the sound exposure level and become relevant for the calculation of single flights. This paper presents a method to classify the atmospheric conditions with idealized vertical profiles derived from weather data of a monitoring station in combination with a radiation balance. The differences of the propagation in a homogenous and a stratified atmosphere are analyzed by exemplary overflights. Additionally, the attenuations due to idealized profiles are compared to those of vertical profiles obtained from flight data records and profiles from a meteorological prediction model. The comparison between the different profiles shows good agreement for temperature, except for the transition between stable and unstable stratification, but larger deviations for humidity. Furthermore it can be shown that the reproduction of a stratified atmosphere in the propagation calculation has a beneficial effect on the accuracy of the resulting sound exposure level and should therefore be taken into account for sophisticated aircraft noise modelling. Therefore, input data of a meteorological prediction model should be used where available, as idealized profiles do not always reproduce the atmosphere accurately.
Full Paper
Prediction of Sound Transmission through Elastomeric Bulb Seals
Atamer, Serkan (1), Çaliskan, Mehmet (1), Özgen, Gökhan O (1)
(1) Middle East Technical University, Turkey
ABSTRACT
Doors are the weakest parts of the buildings in terms of sound transmission. Examination of sound transmission loss characteristics of doors reveals two separate transmission paths to be considered. First one is transmission through door leaf and the second one is leak transmission through elastomeric bulb seals. Seals are the important parts of the sound transmission loss characteristic of door structure. Hence, their insulation capability should be analyzed and optimized to improve sound transmission loss of an acoustical door. The aim of this research is to predict sound transmission loss of elastomeric bulb seals. This assessment includes two main steps. A static analysis is required to determine the seal shape under compression. Seals are made of elastomers which display nonlinear mechanical behavior. This requires hyperelastic material modeling and nonlinear finite element analysis (FEA). An acoustic analysis calculating the sound transmission is then carried on deformed geometry acquired from the first phase of the research. A sample seal geometry, which is already being used in industry, is considered as the case study. Influences of different hyper elastic material models on sound insulation are also studied.
Full Paper
Modeling and experimental validation of cellular porous material with large resonant inclusions
Doutres, Olivier (1), Atalla, Noureddine (1), Osman, Haisam (2)
(1) Université de Sherbrooke, Canada
(2) United Launch Alliance, USA
ABSTRACT
Porous materials are widely used for improving sound absorption and sound transmission loss of vibrating structures. However, their efficiency is limited to medium and high frequencies. A common solution for improving their low frequency behavior while keeping an acceptable thickness is to embed resonant structures such as Helmholtz resonators. This work investigates the absorption and transmission acoustic performances of a cellular porous material with large resonator inclusions. The homogenization theory cannot be applied to cellular material made of such large periodic unit-cell (e.g., cube of side L~100 mm). A low frequency model of a large resonant unit-cell based on the Parallel Transfer Matrix Method is proposed in this work. The proposed model is validated by comparison with impedance tube measurements and finite element calculations. At the Helmholtz resonance frequency; (i) the transmission loss is greatly improved and (ii) the sound absorption of the host material is decreased if it is made of a highly sound absorbing material.
Full Paper
Applying dynamic mechanical analysis to research & development for viscoelastic damping materials
Rasa, Alexander
Pyrotek Noise Control, Australia
ABSTRACT
Dynamic mechanical analysis (DMA) is a versatile method that can provide results for a wide array of parameters relating to material behaviour. In this paper it is used as a method to investigate and characterise the damping properties of viscoelastic materials. Investigations on polymer based viscoelastic damping material samples with varying formulations have been conducted using DMA. Results have been presented and discussed, highlighting the efficiency, accuracy and resolution of the DMA method. The differences in product formulation across the samples and the effect on material characteristics has also been discussed. The results supplied using the DMA method have been shown to be beneficial to research and development for viscoelastic damping materials.
Full Paper
Optimization design method for Constrained Damping layer's noise reduction based on the Hoff sandwich plate theory
Shi, Dongyan (1), Wang, Qingshan (2), Shi, Xianjie (3)
(1) College of Mechanical and Electrical Engineering, Harbin Engineering University, P. R. China
(2) College of Mechanical and Electrical Engineering, Harbin Engineering University, P. R. China
(3) Institute of Systems Engineering, China Academy of Engineering Physics, P. R. China
ABSTRACT
Based on Hoff sandwich plate theory, an analytical method is proposed for predicting the loss factors of constrained damping layer. The application of the current approach in the engineering application of acoustic radiation optimization is examined. Numerical examples regarding isotropic sandwich plate with simply supported boundary conditions are carried out to demonstrate the accuracy and reliability of the current approach. It is shown that the current method has a good accuracy in determining loss factors of constrained damping layer. On this basis, optimization design of constrained damping layer is implemented. The effects of main parameters of damping layer on the loss factors are investigated. Then, the current approach is utilized to application of vibration and noise reduction for gearbox housing. Results show that parameters of damping layer have different effect on the vibration and noise reduction. The optimum design parameter of damping layer can be obtained through comprehensive comparison analysis. This investigation can provide an efficient design scheme of acoustic protection with damping layer for vibration and noise reduction.
Full Paper
Assessment of Vibrations from a Seismic Test Facility
Lee, Yong Keat (1), Mackenzie, Neil (1)
(1) Aurecon, Australia
ABSTRACT
The recent earthquakes in Christchurch led to the redevelopment of the University of Canterbury's Seismic Equipment Laboratory (SEL). The SEL facility will involve the testing of building structures subject to simulated static and dynamic displacements from earthquakes, with a reaction wall and floor used to exert loads by way of hydraulic actuators on test specimens, and shaker tables used to test built forms separately or in combination. These tests can generate significant ground vibration, which has the potential to affect the use of nearby buildings housing sensitive equipment. This paper will outline measurements and analysis carried out to predict the likely vibration levels at the footings and within adjoining buildings. It also outlines methods to mitigate vibration in excess of relevant criteria.
Full Paper
An approach to optimal sensor placement for vibration tests on large structures
Yuan, Chunhui (1), Zhang, Junjie (2)
(1) National Key Laboratory on Ship Vibration & Noise, China
(2) China Ship Development and Design Center, China
ABSTRACT
The critical issue of vibration test on hull structures with large size is the numerous amounts of sensors. Too many sensors lead to excessive consumption whereas notable error would come from reducing the number of sensors. An approach is proposed to reconstruct the complete structural vibration via much fewer sensors. This iterative progress eliminates the sensor location that contributes the most significantly to the condition number of modal matrix in each cycle. Along with the iteration, the condition number goes down quickly to a certain level, but rises suddenly after lots of calculating cycles. The optimal number of sensors is the one before the condition number zooming. The corresponding sensor locations are also optimal. An experiment on cylindrical shell demonstrates that vibration responses reconstructed from the data of 26 optimal sensors are consistent with the responses measured by 200 initial sensors. The vibration error is only 2.4 dB. This approach may be applied to vibration test and measurement on large structures.
Full Paper
Analysis of seismic response on the excitation of support structures
Ziaran, Stanislav (1), Cekan, Michal (1), Chlebo, Ondrej (1), Musil, Milos (1)
(1) Slovak University of Technology, Slovakia
ABSTRACT
Improving the safety of nuclear power plants requires seismic testing of key components. Ever increasing demands on components, devices, and machinery within nuclear power plants, necessitates testing with more extreme loading conditions at low frequencies of vibration. Frequency and modal analyses are very powerful tools for determining excessive or harmful vibration. The goal of the paper is, by means of frequency and modal analyses, to compare the operational frequency spectrum with the Eigen frequencies of an existing support structure. After a suitable measurement point is selected, a frequency analysis is performed and the main sources of vibration are detected. Modal analysis is performed by simulation and measurement. The excitation was generated by a low frequency shake table (up to 100 Hz) capable of generating random and deterministic signals. The Eigen values of the tested structure were compared with the Eigen values obtained by Finite Element Analysis (FEA) of the support structure as well as the response (displacement). For the detection of low frequency waves resulting from vibrating sources, the Fast Fourier Transform (FFT) and modal analysis, in the frequency domain, was used.
Full Paper
Analytical model for the airborne sound pressure waveform radiated when an offshore steel pipe pile is driven with an impact hammer
Hall, Marshall V
Marshall Hall Acoustics, Australia
ABSTRACT
An analytical model has been developed for the airborne sound pressure waveform radiated when an offshore steel pipe pile is struck by a short hammer. The model is based on the coupled equations of motion for axial and radial vibration of a thin shell, and yields frequency-dependent phase velocity and attenuation of these vibrations. A harmonic solution is obtained for the radiated sound pressure, using Junger & Feit's "Transform formulation of the pressure field of cylindrical radiators". The model is applied to a measurement of a 10- tonne hammer with cushion driving a pile 91 cm in diameter and 38 m long, in water 17 m deep. The height of the pile face above the water surface is estimated to have decreased from approximately 15 to 3 m during its driving. SPL (Leq) is examined at the measurement range (15 m) and microphone height (1.5 m). The present model predicts SPL would have ranged between 104 and 109 dB re 20 µPa as the pile face descended. The measured SPL data had an average of 103 dB and a maximum of 111 dB re 20 µPa. Possible reasons for the smaller spread of the model predictions are discussed.
Full Paper
Vibration Input Identification using Dynamic Strain Measurement
Itofuji, Takumi (1), Yoshimura, Takuya (1)
(1) Tokyo Metropolitan University , Japan
ABSTRACT
Transfer Path Analysis (TPA) has been conducted in order to improve the noise and vibration quality of mechanical structures. However, the force identification in the TPA is still challenging problem and its accuracy has to be improved. The Matrix Inversion Method and the Apparent-Mass Matrix Method are approaches for force identification. The Matrix Inversion Method estimates the excitation force by the product of an inverse matrix of accelerance and a vector of actual operational acceleration. It is known that the Matrix Inversion Method is very sensitive to measurement noise especially at the resonance. Apparent-Mass Matrix Method has been recently proposed, which provides more accurate results than the Matrix Inversion Method. However, these methods are still insufficient in accuracy, and improvement of identification accuracy is required. This paper proposes a new force identification method by using strain measurement. The method estimates the force using the Strain Frequency Response Function (SFRF) instead of acceleration or Apparent-Mass Matrix. It is shown that SFRFs are more strongly affected by higher-order modes than accelerance FRF. Therefore, we considered that more accurate force identification can be obtained by using SFRF than the conventional method.
Full Paper
The new method for focusing properties of the acoustical steady field in room
Liu, Song (1), Li, Sheng (1)
(1) DUT,China
ABSTRACT
The phase conjugation method used for the identification and reconstruction of the acoustical steady propagation field in room is studied numerically. The planar array forms of phase conjugation are studied for sound source localization. The numerical results show that: The phase conjugation method can completely achieve the identification and location of the acoustical source in room.
Full Paper
Sound radiation from a water-loaded cylinder due to machine noise
Pan, Xia (1), Tso, Yan (1), Forrest, James (1), Peters, Herwig (2)
(1) DSTO, Australia
(2) The University of New South Wales, Australia
ABSTRACT
This paper presents the modelling and analysis of the noise radiation due to internal acoustic excitation of a cylinder submerged in a heavy fluid. The cylinder consists of a cylindrical shell filled with air and attached to rigid end plates. The acoustic excitation is modelled as monopoles to simulate the operation of a machine noise source in the cylindrical shell. In order to model the noise transmission and radiation, the machine noise is characterised as multiple monopole sources with random amplitudes and random phases on the surfaces of an imaginary component boundary. An initial study including the effect of absorbing material on noise radiation is presented. Some of the analytical results are compared with those from numerical finite element / boundary element models. Excellent agreement is obtained between the analytical results and results from the numerical method.
Full Paper
Acoustic radiation response prediction of thin-walled box with particle dampers using multiphase flow theory of gas-particle
Wu, Chengjun (1), Wang, Dongqiang (1), Yang, Ruichao (1), Lei, Xiaofei (1)
(1) Xi\'an Jiaotong University, China
ABSTRACT
In this paper, acoustic radiation response of thin-walled box with particle dampers is predicted. First, the effect of the collisions and friction between the granular inter-particles is interpreted as an equivalent nonlinear viscous damping based on multiphase flow theory of gas-particle. Then the contribution of particle damper is estimated as an equivalent mass-damper system. And the acoustic radiation response of thin-walled box with particle dampers is predicted in the finite element method. Finally, an originality and novelty simulation method is developed to evaluate acoustic radiation response characteristics of particle damping composite structure by COMSOL. With this as a base, detailed numerical studies using the originality simulation method are also carried out to analyze the acoustic radiation response characteristics of the particle-damping thin-walled box. An experimental verification is conducted, and a good agreement between the theoretical results and the experimental data shows that the theoretical work in this paper is valid
Full Paper
A Rayleigh-Ritz method based on improved Fourier series for vibration analysis of cylindrical shell coupled with elastic beams
Zhang, Runze (1), Cao, Yipeng (1), Li, Liaoyuan (1)
(1) Harbin Engineering University, China
ABSTRACT
A finite circular cylindrical shell model coupled with elastic beams is built in this paper. The beam-shell structure is connected with linear springs and rotational springs. Considering different structural coupling conditions, the Rayleigh-Ritz approach based on improved Fourier series method is employed to analyze the free vibration properties of the calculation model. The improved Fourier series method is used to describe the displacements of the coupling structure, while the Rayleigh-Ritz method is utilized to solve the coefficients. The important advantage of this approach is that it can be universally applied to the coupling structure with a variety of different boundary and coupling conditions. The results are verified by the finite element method. It's shown that the proposed approach is a convenient, efficient and accurate one for determining the modal behavior of such a complex structure system.
Full Paper
Research on sound insulation of multiple-layer structure with porous material and air-layer
Bai, Guofeng (1), Zhan, Pei (1), Sui, Fusheng (1), Yang, Jun (1)
(1) Key Laboratory of Noise and Vibration Research, Institute of Acoustics, Chinese Academy of Sciences, China
ABSTRACT
Sound insulation performance of multiple-layer structure is investigated which consists of elastic solid, fluid and porous material. The Biot theory of sound propagation in elastic porous medium and the method of transfer matrix are used to derive the transmission loss of typical layered-structure. The influence of air-layer and porous material on sound insulation performance of multiple-layer structure had been discussed by numerical calculation and experimental testing. The result indicates that the air-layer and porous material can improve sound insulation performance of multiple-layer structure and their distribution also has great influence on the sound insulation performance.
Full Paper
Design of a standalone, modular test facility for measuring sound transmitted through a common ceiling plenum
Barclay, Edward A (1), Wareing, Robin R (1), Pearse, John R (1)
(1) University of Canterbury, NZ
ABSTRACT
The design of a modular ceiling test facility is described. The University of Canterbury's acoustic test facilities are undergoing substantial renovation and in some cases replacement. A number of new test facilities are being constructed. These test facilities must be relatively low cost, and be able to be easily stored. A facility for testing suspended ceilings to ASTM E1414 and ISO 10848 has been developed. The reverberation time within the facility was modelled utilising measured absorption data to ensure the design was within acceptable levels. The direct and indirect sound transmission paths were assessed.
Full Paper
Sound insulation of application for composite wood panel
Chou, Chuan-Wen (1), Chen, Chen Yu (1), Lai, Rong Ping (2), Sun, Philip (3)
(1) National Cheng Kung University, Taiwan
(2) NCKU Research and Development Foundation
(3) Ping Shen Enterprises Co., Taiwan
ABSTRACT
Glued laminated timber, also called Glulam, was applied on various building components, space products, and decoration materials. The extensively application of Glulam was attributed to its feature with durable, ease processing, attractive appearance, and sustainability. According to the feature of Glulam, in present the Glulam was frequently used to combine with multiple materials such as metal, gypsum panel, rubber, and even paper materials. The composite wood panel with multiple materials would be effective to fire prevention and sound insulation. However, the analysis of sound insulation of composite wood panel was still focused on the surface density but no more controlling factors of sound insulation for quantitative analysis. By the new technique of composite wood panel, the uncertain of quality analysis would cost wasting from repeatedly replacement during construction just because of the ineffective sound insulation analysis. This study was focused on Glulam. The composite wood panel would be combined with different material. Furthermore, it was confirmed for the influence of sound insulation with various factors, such as the location of material, rigidity, and simple mechanism. The raising surface density for the material near the median of panel section would promote the sound insulation between 500 Hz to 2000 Hz with about 5 dB. In the other side, the raising rigidity and resonance frequency for the material near the surface of panel to 7 dB. Above this study, it could extend to more analysis for composite wood panel, and would make more effective accuracy for sound insulation analysis.
Full Paper
Vibration reduction in lightweight floor/ceiling systems with a sand-sawdust damping layer
Chung, Hyuck (1), Emms, Grant (2)
(1) Auckland University of Technology, New Zealand
(2) NZ Forest Research Institute Ltd, New Zealand
ABSTRACT
This paper shows how to use a mathematical model to predict the vibration of lightweight timber-framed floor/ceiling systems (LTFSs) caused by mechanical excitation. The LTFS considered here is made up of an upper floor layer, a cavity space with timber joists and a ceiling. These components are joined by timber battens, ceiling furring channels and ceiling clips. The vibration in the structure is caused by a localized excitation on the top surface and the resulting vibration level of the ceiling surface will be analysed. The cavity space is filled with fibre infill for damping the sound transmitting through the cavity. A unique feature of the design and the model is the sand-sawdust mixture in the upper layer. The theoretical model and the experimental measurements show that the sand-sawdust dampens the vibration in the frequency range between 10 and 200 Hz. The damping by the sand-sawdust and the fibre infill are found by comparing the numerical simulations against the experimental measurements. We show that the simple linear frequency dependent loss factors can be used to predict the low-frequency vibrations of LTFSs.
Full Paper
The equivalent translational compliance of steel studs and resilient channel bars
Hirakawa, Susumu (1), Davy, John Laurence (1)
(1) RMIT University, Australia
ABSTRACT
A number of recent papers have determined the compliance of steel studs for use in a model for predicting the sound insulation of cavity stud walls. Previously, the steel studs have usually been modelled as line connections. In this paper, they are also modelled as point connections where the points are the screws attaching the wall leaves to the steel studs. The compliance of the combination of resilient channel bars and wooden or steel studs, modelled as point or as line connections, is also presented. The values of compliance which make a theoretical model agree with the experimental data have been calculated. The experimental sound insulation data were measured by the National Research Council of Canada. There were 126 steel stud walls, 78 resilient channel bar and wooden stud walls, 15 resilient channel bar and steel stud walls and 4 walls with resilient channel bars on both sides of wooden studs. Linear regressions of the logarithm of the compliance against the logarithms of frequency, reduced surface density, cavity depth and number of point connections or stud spacing, were conducted in a low frequency range and in a high frequency range. The equations produced by these linear regressions can be used in sound insulation prediction models.
Full Paper
Noise control by design: A tool intended for architectural use
Sentop, Ayca (1), Tamer Bayazit, Nurgun (2), Altun, M Cem (2)
(1) Istanbul Bilgi University, Turkey
(2) Istanbul Technical University, Turkey
ABSTRACT
This study aims to present a building elements selection tool, which has been generated to assist architects with determination of acoustically appropriate assemblies at the preliminary design stage. In order to succeed, practicality, easy usage and reliability are considered essential for every step. In this context a catalogue and a calculator are generated as components of the tool. The catalogue constitutes a database in which building elements are subcategorized according to their constructional and acoustical characteristics. Acoustical measurement results of 587 different assemblies are collected from relevant literature and their technical drawings are prepared in order to provide easy selection. The calculator serves to simplify the calculations by giving the sound insulation requirement according to outdoor noise levels and acceptable background noise levels. The calculator also determines composite (average) sound insulation value of building elements composed of multiple components. Background noise criteria and data from the catalogue are predefined in the calculator, simplifying data insertion and parallel usage of the catalogue and the calculator. In order to prove efficiency and practicality of the building elements selection tool, its usability by architects is tested on subjects with a sample design problem and outcomes are discussed.
Full Paper
Challenges for acoustic calculation models in \"Silent Timber Build\", Part 1- FEM
Bard, Delphine (1), Negreira, Juan (1), Kouyoumji, Jean-Luc (2), Borello, Gérard (3), Guigou, Catherine (4)
(1) Lund University, Sweden
(2) FCBA,France
(3) InterAC, France,
(4) CSTB, France
ABSTRACT
The project "Silent Timber Build" will develop new prediction tools for timber structures. There are several challenges that have to be overcome to provide a full prediction tool. The differences in weight, stiffness and density for wooden structures compared to traditional, heavy and more homogeneous structural material have repercussions on how the sound propagates throughout the structures, affecting the sound and vibration insulation performance and also theories to be used in prediction models. Finite element simulations have proved to be useful in the design phase in a certain low and very low frequency range. By further developing reliable finite element tools for low frequencies, the performance of future wooden constructions can be predicted in a full frequency range, saving both time and money as all calculations, and modifications can be done during the design phase. However the upper limit for using FEM has to be further investigated and then be merged with statistical methods. This article, following another article Part 2, will focus on medium and high frequency range calculations. For full-scale building, Virtual SEA method, as analytic and SEA approaches will be used in frequencies low enough in order to optimize the overlap to FEM.
Full Paper
Acoustic Solutions for Wooden Intermediate Floors
Bartlomé, Olin (1), Liebl, Andreas (1)
(1) Lignum, Switzerland
ABSTRACT
In Switzerland multi-storey timber construction has been very successful in recent years. This is primarily due to the 2005 amended fire safety regulations. This development brought with it new challenges with regard to sound mitigation. Apart from requirements governed by national standards, there are requirements driven by occupants. These are based on subjective human perception and can lead to complaints about low-frequency sound even if the values specified in the standard are met. Research was therefore carried out on the subjective assessment with in-situ measurements, a broad survey and auditory tests. Additionally common details and their robustness where evaluated and within 4 case studies examined. The results of the research project in short are:
- The frequency range for sound insulation needs to be considered from 50 Hz
- Building elements show a wide range of construction principles and acoustic properties. A structured online catalogue with robust details was developed
- With good floor build-ups, the flanking transmission is of minor importance
- One main reasons for the small sound insulation properties of timber constructions in the low frequency range is the low mass
- The quality of elements/buildings must be guaranteed. Timber constructions can be controlled significantly in industrialised building systems
Full Paper
Cost benefit analysis of acoustic treatments for inner-city residential premises near entertainment venues
Borgeaud, David
Air Noise Environment Pty Ltd, Australia
ABSTRACT
Brisbane's Fortitude Valley is an inner city area combining retail, commercial, residential, and entertainment uses. For many years it has been the starting point for major Australian bands. The Valley's "Urban Renewal" has seen a large increase in the number of residential apartments, which has led to concerns regarding the impact this may have on the future of live music in the Valley. Brisbane City Council has developed entertainment precincts with specific noise criteria within the Valley (as part of the Valley Music Harmony Plan). Earlier papers by the Author addressed the ambient noise mapping and treatment of venues investigation, and this paper discusses the cost benefit study undertaken of acoustic treatment for existing residential premises. The purpose of this work was to provide Council with information on both the feasibility of treating the apartments to control low frequency noise and the order of cost for the treatments. The study found that attenuation of 2 - 16dB(C) could be achieved using a variety of site specific treatments with costs ranging from $34,000 to $64,000. The costing work proved an invaluable piece of knowledge in the implementation of the Valley Music Harmony Plan.
Full Paper
Improvement effect of the infrasound and vibration due to repair of the bridge
Fukada, Saiji (1), Kaneishi, Yoshimune (2), Hama, Hirokazu (3), Okada, Hiroyuki (3)
(1) Kanazawa University, Japan
(2) West Nippon Expressway Co., Japan
(3) Fujiengineering Co., Japan
ABSTRACT
Recently, increasingly heavy traffic flow volumes have led to fatigue damage in the deck and pavement of bridges. Heavy trucks are a major contributor to such damage, causing environmental vibration problems such as infrasound and ground vibration. These vibrations are known to be transmitted through bridges to nearby houses. This study investigated bridges that caused such problems in nearby houses. Bridge repairs were performed to solve these problems. The improvement in infrasound and ground vibration upon bridge repair was investigated using a test truck and ordinary trucks. The ground vibration of the abutment with frequencies of 10 Hz or more decreased greatly as did the ground vibration outside the houses. Furthermore, infrasound with frequencies of 10-20 Hz decreased.
Full Paper
Low frequency sound transmission in multifamily wooden houses
Hagberg, Klas (1), Bard, Delphine (2)
(1) WSP, Sweden
(2) Lund University
ABSTRACT
In the recently finished research projects, AkuLite and AcuWood, it is clearly stated that low frequencies should be considered far more, prior to design new wooden structural building system. Lower than 50 Hz is preferable, and the most annoying frequencies appear between 20 and 50 Hz. However, it is still a long way to go in order to convince acousticians, the entire global industry and authorities that these frequencies have to be considered in order to build wooden structures which are experienced by the habitants as equally good as heavy structures. To "save" the industry, a lower limit of at least 50 Hz at least for impact sound should be mandatory in the near future globally, in spite of the fact that the new standard ISO 16717 will not be reality. This paper describes the main reasons why it is needed to include these low frequencies in residential buildings. It describes different constructions and their appearance due to low frequency impact sound transmission. The paper comprises some examples designed to fulfill the Swedish requirements, which equals L ́n,Tw and L ́n,Tw+CI,50-2500 ≤ 56 dB between dwellings. It comprises also a discussion regarding optimizing constructions for various uses, e.g. different types of housing.
Full Paper
Comparison of the results of a laboratory experiment and a field study with regard to acoustic quality in wooden buildings and recommendations for classification of acoustic quality
Liebl, Andreas (1), Späh, Moritz (2), Bartlomé, Olin (1), Kittel, Maria (1)
(1) Fraunhofer Institute for Building Physics, Germany
(2) Lignum Holzwirtschaft, Switzerland
ABSTRACT
Within the European research project AcuWood a questionnaire-based field study in Germany and Switzerland as well as laboratory listening tests were conducted which aimed at the evaluation of low frequency impact noise in wooden buildings. Different building and construction types were reconsidered. Since the laboratory listening tests partly included recordings from buildings that were also included in the questionnaire-based field study, it is possible to compare the long-term acoustic satisfaction of inhabitants with the short-term subjective impression during the laboratory listening tests. The results which were already reported at the Internoise 2013 have been enriched by another dataset. Recordings and listening tests of a lower quality wooden building were added in order to test the reliability of the comparability between the laboratory test and the field study. It is also discussed to use data from listening tests as a basis for the classification of acoustic quality in order to ensure for the perceptibility of defined different acoustic qualities.
Full Paper
Designing and delivering the right sound for quiet vehicles
Allman-Ward, Mark (1), Williams, Roger (2), Heinz, Thorsten (1), Demontis, Maurizio (3)
(1) Bruel & Kjaer, UK
(2) Bruel & Kjaer, USA
(3) Bruel & kjaer, AUS
ABSTRACT
Creating the right sound for quiet vehicles is extremely important. External warning sounds must reflect the vehicle brand image and be accepted by owners, whilst having good warning characteristics and harmonising with the environment. Internal sounds can be used to convey vehicle status, whilst enhancing the brand and driving pleasure. Since these vehicles are quiet, there is much broader scope for styling the sound that they should make. However, evaluating and selecting alternative sounds is extremely time and labour intensive if done in the real world because of the large number of vehicle and environmental factors which can influence the perception of the sound, especially outside the vehicle. This paper outlines a process where the exterior and interior sounds of vehicles are evaluated efficiently in the virtual world. The consensus derived from subjective jury can be gathered quickly and cheaply, leading to a shortlist of sounds to be tried on a real vehicle. It introduces a toolset which uses the same data and algorithms for designing sounds in the virtual world and validating them in the real world. The same data can also be used directly in a production series by embedding the software algorithms into the production vehicle hardware.
Full Paper
Sound design of electric vehicles - Challenges and risks
Genuit, Klaus (1), Fiebig, André (1)
(1) HEAD acoustics GmbH, Germany
ABSTRACT
Sound quality depends on cognitively processed features referenced to an assigned set of expectations. It describes the perception of suitability and desirability of a sound attached to a certain product. However, since experiences of electric vehicle technology and established expectations rarely exist, several questions remain unanswered. What are the references customers use to evaluate sound quality of electric vehicles? How to meet customers' needs without established targets? Is it possible to simply set sound quality standards, where customers will increasingly adapt to?
Experiments and interviews are needed to answer reliably these questions. It is evident that successful sound design of electric vehicles depends on several aspects. Besides customer preferences, technology image, strategies of car manufacturers, economic and ecological factors, the social discussion of electric vehicle technology will contribute to the acceptance or rejection of sound design concepts. In fact, expectations are socially shaped and the impact of public discourse on expectations must be considered.
The paper will present results gained in test drives, where subjects drove electric vehicles and commented different sound concepts. Moreover, the experimental results will be discussed from a broader contextual perspective.
Full Paper
Subjective evaluation of additive sound designed to reinforce acoustic feedback of electric vehicle
Gwak, Doo Young (1), Yoon, Kiseop (1), Seong, Yeolwan (1), Lee, Soogab (2)
(1) Seoul National University, Republic of Korea
(2) Center for Environmental Noise and Vibration Research, Engineering Research Institute, Seoul National University, Republic of Korea
ABSTRACT
Because booming sound of internal combustion engine is eliminated in electric vehicle (EV), it has been complained that EV is not fun-to-drive and drivers cannot get information of driving speed by its sound. In order to overcome this problem, signal processing method of additive engine sound has been suggested. However, because it strongly affects interior sound quality and so does brand image, this strategy must be carefully evaluated before applied. In this study, two types of signal processing methods were adapted to recorded EV sound and subjective evaluation was conducted. Total 10 stimuli were judged by 30 drivers in terms of sensation of acceleration, sound image, and preference. Effects of each signal processing method are compared and advantages and disadvantages of each method are discussed.
Full Paper
Urban environment audio simulation for contextual evaluation of Quiet Vehicles\' sound design
Misdariis, Nicolas (1), Gerber, Julien (1), Aleonard, Julien (2)
(1) UPMC, France
(2) Ircam, France
ABSTRACT
The silence of Quiet Vehicles - especially, Hybrid or Electric Vehicles - is a crucial issue in terms of safety, ergonomics or even ecology which becomes to be largely studied either in a research or development point of view. Most of the works done in that domain are based on experiments which try to measure presence and emergence of such vehicles in real, or simulated, environment and to evaluate their detectabilty, in the same contexts, while being equipped with extra sounds specifically designed for fulfilling basic functional conditions with regards to nearby pedestrians or other road users. In this necessary experimental workflow, we assume that simulation approach - or, more generally, virtual reality - is a potentially powerful and valid paradigm to test the contextual impact of a large number of propositions and to conduct controled laboratory experiments for evaluation. This paper will then present the first step of the development of an audio simulation based on Ambisonics field recordings in various urban locations, multi-channel audio rendering and mock-up of different audio scenarios for insertion of one or multiple QV sound signatures in a given sound scene. Next steps - together with general stakes and perspectives - of this approach will also be presented and discussed.
Full Paper
Development of a next-generation audible pedestrian alert system for EVs having minimal impact on environmental noise levels
project eVADER
Quinn, David C. (1), Mitchell, Josh, Clark, Paul
(1) Nissan, UK
ABSTRACT
The silent operation of Electric Vehicles (EVs) and Hybrid Electric Vehicles (HEVs), at low speeds, has provoked significant concern regarding increased risk to pedestrian safety. Conversely, the relative silence of EVs is seen by others as a positive feature and a rare opportunity to reduce environmental traffic noise levels. The prevailing solution to the pedestrian safety concern is to add artificial sounds to EVs, in order to improve their detection by pedestrians and other vulnerable road users. However, this approach may not satisfy the need to reduce environmental traffic noise pollution levels, unless a solution can be found which satisfies these conflicting requirements.
eVADER (electric Vehicle Alert for Detection and Emergency Response) is a European Commission, part funded, project which is developing a next-generation audible alert system solution for EVs and HEVs. The prime objective of eVADER is to develop a practical solution whereby effective audible alert systems added to EVs can have minimal impact on environmental noise levels.
This paper describes the eVADER pedestrian alert system concept and practical installation of the system into a Nissan LEAF demonstrator car, together with initial results of system performance.
Full Paper
Detectability and hearing impression of additional warning sounds for electric or hybrid vehicles
Yamauchi, Katsuya (1), Sano, Takaichi (2), Hasegawa, Shin (2), Tamura, Fumio (2), Takeda, Yuichiro (2)
(1) Nagasaki University, Japan
(2) Pioneer Corporation, Japan
ABSTRACT
Electric or hybrid electric vehicles (EVs/HEVs) have the advantages that they make lesser noise compared to conventional engine vehicles. This quietness is, however, a matter of concern for pedestrians because the sound of EVs/HEVs may be inaudible in urban backgrounds. Hence, the application of additional sound- emitting device has been studied. Gathering wide range of acoustic knowledge on feasible design of the additional sounds is crucial for developing regulations or designing the device itself. Through the authors' re- searches, it has been revealed that the type of warning sounds significantly affected the required sound level as well as background levels. A warning sound stimulus, which had lesser loudness level, had lesser detectabil- ity. In this present study, the authors confirmed that the warning sounds could have similar detectability if they have similar loudness level. The frequency characteristics of the stimuli were varied while having equiv- alent powers in each 1/3 octave band so that they shall have equivalent loudness level. Moreover, the hearing impression of the stimuli were examined. The results showed that the impression of warning sounds could be varied while having equal detectability.
Full Paper
Effects upon the urban noise of prioritizing bicycle traffic at intersections
Cueto, Jose Luis (1), Hernandez, Ricardo (1), Fernandez, Francisco (1), Sales, Diego (1), Priego, Javier Cristino (1)
(1) University of Cadiz, Spain
ABSTRACT
The term "Smart-Mobility" will probably be commonly used in traffic management in the cities in the twenty-first century. But this concept not only involves issues related to mobility, but also sustainability and efficient use of information technology. In this sense, urban experts have lately paid great attention to the promotion of cycling as a daily mode of transport. This paper aims to explore the possibilities of establishing the right of way to the flow of cyclists at signalized junctions and to describe the consequences it may have on environmental noise. However, this strategy of urban mobility would not have been feasible without the prior development of increasingly more reliable detection technologies of bikes as part of intelligent control systems at intersections. Considering that these intelligent systems have traditionally been used to avoid traffic jams as well as to give priority to public transport, this approach could involve new ways of thinking and imagining the modern city. This work is developed in a simple arterial where upon it is studied under which conditions these traffic control systems are more or less efficient through the network. For this purpose, a VISSIM traffic micro-simulation model has been applied.
Full Paper
Noise modelling of road intersections
Lau, Akil (1), Lee, Yong Keat (1), Dawson, Bill (1), Name, Neil (1)
(1) Aurecon, Australia
ABSTRACT
Road traffic noise modelling is usually performed with statistical models (e.g. Calculation of Road Traffic Noise "CORTN" algorithm) and calibrated based on experimental data related to standard conditions and assumptions such as free flow constant-speed traffic with uniformly distributed vehicles. However, as the standard modelling approach does not take into account traffic dynamics, traffic noise emission from intersections are not always modelled correctly. In this paper, analysis of an intersection is presented based on a case study. Noise measurements were conducted to characterize the existing noise environment. The measurement data was compared against the simulated noise model. The study outlines a method to account for traffic dynamics such as deceleration / acceleration / stop / start and low speed of traffic at junctions to improve predictions of traffic noise.
Full Paper
Road traffic noise prediction model \"ASJ RTN-Model 2013\" proposed by the Acoustical Society of Japan
- Part 2: Study on sound emission of road vehicles
Okada, Yasuaki (1), Tajika, Terutoshi (2), Sakamoto, Shinichi (3)
(1) Meijo University, Japan
(2) Environmental Technical Laboratory, Japan
(3) University of Tokyo, Japan
ABSTRACT
The Acoustical Society of Japan (ASJ) has published a new revised version of road traffic noise prediction method "ASJ RTN-Model 2013", in which the calculation formulas for the A-weighted sound power level of each type of road vehicle are specified. The sound power level is given simply as a function of the running speed in consideration of practicality and convenience. The several calculation formulas in this model had been developed using the measured data in 1991-1998. Since 2009, the Research Committee in ASJ has been accumulating new data about noise emission of road vehicles. In this study, the A-weighted sound power levels measured during the 1990's were compared with those in recent years. In addition, during the last decade, hybrid and electric vehicles are becoming popular and the number of production is rapidly increasing. The noise reduction effect of these low-emission vehicles was examined. As a result, it has been found that there are not any remarkable differences between the sound power levels measured in the 1990's and those in recent years, and the noise reduction effect of low-emission vehicles could be applied to the noise prediction in the vicinity of signalized intersections or expressway tollgates.
Full Paper
The effects of vegetation on road traffic noise
Peng, Jeffrey (1), Bullen, Robert (1), Kean, Simon (2)
(1) Wilkinson Murray Ptd Ltd, Australia
(2) Roads and Maritime Services, Australia
ABSTRACT
In Australia road traffic noise is generally described as LAeq, and is typically assessed using the Calculation of Road Traffic Noise (CoRTN) standardised calculation procedures (with some modifications). However, the CoRTN methodology, like most other noise propagation algorithms, neglects the effects of highly vegetated areas on sound propagation. The aim of this study was to review available literature as well as to obtain specific experimental data to provide a better understanding of noise transmission when significant vegetation is present. The excess attenuation of traffic noise through 10 to 20m of trees (tree spacing <0.5m) was found to be typically 2 to 3dB(A), and up to 7dB(A) through 120m of eucalypts (spacing >0.5m), relative to CoRTN predictions. After bushfire, it was found that excess attenuation can still be expected as a result of multiple scattering by tree trunks. The conclusion of the data analysis and literature review has shown that vegetation has the potential to inform urban design and compliment other forms of noise mitigation.
Full Paper
Road traffic noise prediction model \"ASJ RTN-Model 2013\" proposed by the Acoustical Society of Japan
- Part 1: Outline of the calculation model
Sakamoto, Shinichi (1), Matsumoto, Toshio (2), Tajika, Terutoshi (3), Fukushima, Akinori (4)
(1) Institute of Industrial Science, The University of Tokyo, Japan
(2) Kobayasi Institute of Physical Research, Japan
(3) Environmental Technical Laboratory, Japan
(4) NEWS Environmental Design Inc., Japan
ABSTRACT
The Acoustical Society of Japan organizes the Research Committee on Road Traffic Noise to develop a prediction model of the road traffic noise. As results of the continuous research activities, the road traffic noise prediction model has been continuously published. Especially since 1993, the model has been released every five years. In this April, the latest version, "ASJ RTN-Model 2013", was published. It is an up-grade version of the previous model, ASJ RTN-Model 2008, and it was revised based on new knowledge and novel technology. In this paper, the calculation principle, the general procedure of the prediction calculation, the outline of the revision of the ASJ RTN-Model 2013 are introduced.
Full Paper
Hydro sound measurements during the installation of large diameter offshore piles using combinations of independent noise mitigation systems
Bruns, Benedikt (1), Stein, Philipp (1), Stein, Philipp (1), Kuhn, Christian (1), Gattermann, Jörg (1)
(1) TU Braunschweig, Germany
ABSTRACT
During the installation of pile foundations for offshore wind farms (OWF) in the German North Sea, hydro sound emissions occur which are harmful to marine life. Limiting values defined by German authorities could not be met by the use of single noise mitigation systems (NMS) in past wind farm installations with large diameter monopiles. To improve noise reduction, combinations of several NMS are used in recent projects. Different NMS taking affect in different frequency ranges can reduce noise caused by impact driving more effectively. During offshore measuring campaigns at an OWF in the German North Sea, hydro sound measurements have been carried out in 7 distances from 15 m to 1500 m and in 5 depths from 1 m to 17 m over ground simultaneously. Results of these measurements will be shown in the time and frequency domain. Pile driving noise emissions with single NMS and combinations of NMS will be compared with reference measurements without NMS to evaluate different setups. The influence of the subsoil will be discussed as well as it has a significant influence on hydro sound propagation in general and the effectiveness of NMS in particular.
Full Paper
New Hydro Sound Dampers to reduce piling underwater noise
Elmer, Karl-Heinz (1), Savery, John (2)
(1) Offnoise Solutions GmbH, Germany
(2) Savery and Associates Pty Ltd, Australia
ABSTRACT
Underwater noise is a severe annoyance and danger to marine life. The innovative Hydro Sound Dampers (HSD) lead to an effective general method to reduce piling underwater noise. HSD were developed between 2007 and 2010 by K.-H. Elmer to reduce marine and offshore piling noise. The theory and the acoustical background of the new noise mitigation method will be presented. HSD systems use nets with air filled elastic balloons and special PE-foam elements with high dissipative effects to reduce continuous and impact noise. The resonance frequency of the HSD-elements, the optimum damping rate for impact noise, the distribution and the effective frequency range can be fully controlled. Offshore tests and serial applications in offshore wind farms in Germany and Great Britain demonstrate this new effective way to reduce the very high offshore piling noise. It is also intended to use systems of Hydro Sound Dampers in Australia to reduce high underwater piling noise levels in coastal ports and harbours. HSD-systems are very small systems and easy to handle. They are more effective than air-bubble curtains, independent of compressed air, not influenced by tidal currents, not expensive and easy adaptable to different applications. Measured results of underwater noise reductions between 10dB (SEL) and more than 20dB (SEL) will be presented and discussed.
Full Paper
Dynamic measurements of pile deflections as a source of underwater sound emissions during impact driving of offshore pile foundations
Kuhn, Christian (1), Sychla, Hauke (1), Stein, Philipp (1), Bruns, Benedikt (1), Gattermann, Jörg (1), Degenhardt, Jan (2)
(1) TU Braunschweig, Germany
(2) E.ON Climate & Renewables Central Europe GmbH, Germany
ABSTRACT
Open ended tubular steel piles are used as a state of the art technique for the foundations of offshore wind turbines (OWT). The commonly used means of installation, impact driving, results in massive sound emissions into the seawater and the subsoil which are harmful for marine life. Current research carried out at the Institute for Soil Mechanics and Foundation Engineering of the Technische Universität Braunschweig covers wave propagation in and between driven piles, subsoil and water. This paper focuses on the properties and the propagation of the elastic waves through an impact driven monopile during its installation and the mechanisms of noise induction into water and subsoil. Within the scope of a research project funded by the German federal government measurements have been carried out during the erection of large diameter monopiles for an offshore wind farm (OWF) in the German North Sea. Axial and tangential strains as well as axial and radial accelerations along the length of the piles will be evaluated concerning the noise generating interactions between pile and water and pile and soil respectively.
Full Paper
On the estimation of prediction accuracy in numerical offshore pile driving noise modelling
Lippert, Tristan (1), Heitmann, Kristof (1), Ruhnau, Marcel (1), Lippert, Stephan (1), Von Estorff, Otto (1)
(1) Hamburg University of Technology, Germany
ABSTRACT
Due to the massive, worldwide increase in the number of constructed offshore wind farms, the ecological impact of construction sites has become an important issue. Hereby, the topic of sound radiation from the needed pile driving procedures for the pile foundations of the turbines has gained a lot of attention lately. Therefore, several numerical models are currently developed to accurately predict sound pressure levels (SPLs) in several kilometers distance to the pile. The topic of parameter uncertainties, being important for every numerical model, is of special significance for these predictions. The extremely large dimensions of the domain of interest and the difficulties in determining, for example the bottom parameters, inevitably lead to a significant degree of uncertainty for the input parameters of the model. In this contribution, a coupled finite element/wavenumber integration model is presented and validated by measurements. Subsequently, the validated model is used to exemplify the effect of parameter uncertainties on the resulting SPLs in the water column, using Monte Carlo simulations. Hereby, the sensitivity of the model to different input parameters is given, as well as a quantification of the resulting prediction accuracy.
Full Paper
An efficient model for prediction of underwater noise due to pile driving at large ranges
Nijhof, Marten J J (1), Binnerts, Bas (1), De Jong, Christ A F (1), Ainsle, Michael A (1)
(1) TNO, The Netherlands
ABSTRACT
Modelling the sound levels in the water column due to pile driving operations nearby and out to large distances from the pile is crucial in assessing the likely impact on marine life. Standard numerical techniques for modelling the sound radiation from mechanical structures such as the finite element (FE) and boundary element method are not well suited to predict the sound field efficiently at large ranges. Models better suited for prediction of sound propagation in waveguides over large distances, such as wavenumber integration and ray tracing, require careful attention in order to capture the source characteristics of a complex source such as a pile radiating from both water and sediment. To circumvent these issues, a new hybrid model is proposed using a local FE model that accurately captures the source characteristics of the pile which is coupled to a normal mode based model for efficient evaluation of the sound propagation over large distances in a range dependent environment. The model is validated using the well-known solution for a point source in a Pekeris wave guide. Results are shown for a generic pile driving scenario that was used in the international benchmarking workshop COMPILE for underwater pile driving models.
Full Paper
Sharing ideas about noise management and community design
Dubbink, David
Noise Management Institute, USA
ABSTRACT
Noise control has an established role protecting the public from annoying or damaging sounds. But protection from harm is not the same as the promotion of good. The Soundscape concept adds this essential linkage; providing insights and technologies that help communities construct improved acoustic environments. It expands ways of evaluating sound; moving beyond traditional descriptors to include a rich consideration of the diverse ways people experience sound.The paradigm shift in community noise management is occurring simultaneously with the explosion of mobile and web technologies. These also are changing established approaches to noise control. Phones or tablets can be turned into sound level meters so anyone can measure sound exposure levels. Individuals can record their audio and visual experiences, replicating the "soundwalk", that is a fundamental tool of Soundscape analysis. At some point, expert studies or crowd-sourced measurements by individuals must be consolidated so the diversity of experiences can be interpreted into designs and policies. The Interactive Sound Information System, developed by the author, was designed to produce shared aural experiences and a way of collectively imagining future sound environments. It provides one example of how sound management issues can be presented to concerned communities and decision makers.
Full Paper
The measurement of soundscapes - Is it standardizable?
Genuit, Klaus (1), Fiebig, André (1)
(1) HEAD acoustics GmbH, Germany
ABSTRACT
Beyond doubt, soundscaping is on the rise. Soundscape investigations are increasingly performed and soundscape research takes place extensively in recent years. Unfortunately, there is little agreement about adequate measurement procedures, reporting requirements and soundscape indicators. Although the general openness, interdisciplinary roots and multi-dimensionality of the soundscape approach are very important to preserve, a certain consensus about measurement procedures, reporting requirements and analyses tools is needed. In particular, a common denominator with respect to measurement procedures is required, since due to the diversity of measurement procedures the comparability and compatibility of soundscape investigations is very limited. The paper will refer to recent soundscape studies and their outcomes and will discuss the applied methods and procedures. Since the standardization of soundscape aspects is already under way (ISO/DIS 12913), e.g. regarding terms, minimum reporting requirements and measurement protocols, a thorough discussion of soundscape methods and procedures is imperative.
Full Paper
Soundscape mapping in urban contexts using GIS techniques
Hong, Joo Young (1), Jeon, Jin Yong (1)
(1) Hanyang University, South Korea
ABSTRACT
Urban acoustic environments consist of various sound sources including traffic noise, human-generated sounds, and natural sounds that affect the soundscape perception of a given location. However, these sound sources are indistinguishable by noise maps that are based on sound pressure levels. Hence, soundscape maps based on the perception of sounds are necessary to describe an acoustic environment more accurately. Presented herein is a study of soundscape perception, which employs GIS techniques to generate soundscape maps in various urban settings including commercial, business, recreational, and residential spaces. Soundscape perceptions and physical characteristics of the acoustic environments pertaining to these urban settings were evaluated from questionnaire surveys and acoustic measurements, respectively. The results demonstrate how soundscape perceptions and spatial variation in urban soundscapes are closely related to their corresponding urban contexts.
Full Paper
How do ordinary people evaluate noise pollution in the context of environmental issues?
Nagahata, Koji
Fukushima University, Japan
ABSTRACT
Noise pollution is an environmental issue, and noise policies should thus be developed in the context of such issues. Noise policies also need to reflect public opinion; thus, in developing noise policies, it is important to understand the opinions of ordinary people. This study investigates the evaluation by ordinary individuals of the importance of and their familiarity with noise pollution in the context of environmental issues. A two-dimensional mapping method, which was developed in the field of health education and health promotion, was employed. Participants were asked to evaluate eight items—air pollution, water pollution, soil pollution, odor, noise pollution, ground subsidence, greenhouse gasses, and radioactive pollution—in terms of their importance and familiarity. Noise was most frequently evaluated as the least important environmental issue by the participants, though familiarity with noise pollution varied widely among them. Some participants did evaluate noise pollution as an important and familiar issue: those participants also tended to regard odor as an important issue and to evaluate greenhouse gasses and radioactive pollution, which cannot be sensed directly, as unimportant and unfamiliar.
Full Paper
On seeking methodology to \"measure\" a soundscape
Schomer, Paul D
Schomer and Associates Inc. USA
ABSTRACT
For the soundscape concept to be of practical use it must be able to "measure" the contribution of various contexts to the overall resulting soundscape. The metric used in the "measurement" has at least one requirement. That is, it must be such that if A is better than B and is better than C than A is better than C. Recently Schomer et al. showed that at least for soundscapes not judged positively that the single number given by CTL Fidell et al. represents and effectively quantifies the sum of all community contexts. This is a start in that in these instances we know the sum but to make improvements in understanding soundscape it is necessary to know how each piece contributes so that in the future we can tailor the contexts to improve the overall outcome. In this paper we examine these issues and suggest some contexts that currently can be at least estimated.
Full Paper
Soundscape Identification in Noise Annoyance Evaluation
Yu, Lei (1), Kang, Jian (2), Liang, Hong (2), Xie, Charles (2)
(1) UK
(2) China
ABSTRACT
Living in modern cities is being interfered by ambitious noise more and more seriously. Present controlling approach is to monitor sound pressure level, which only describes one characteristic of a sound environment and ignores its influence on people too. Many studies proved that noise annoyance is not only determined by sound pressure level but also by soundscape that a person identifies. Since a bird singing or water babbling is perceived quieter than a traffic roaring even both having the same sound pressure level, it is considered that soundscape identification plays an important role in subjective evaluation of noise annoyance. Therefore, this study is going to explore how soundscape identification in determining noise annoyance evaluation within a city context. The study investigates four places in an ecological residential area that contains completely nature, nature mixed with man-made, and complete man-made soundscapes. Using recordings of the four study-sites, physical characteristics of a diversity soundscape have been analyzed and relationships of a soundscape's physical characteristics with noise annoyance evaluation have been studied.
Full Paper
Evaluation of Diesel powertrain noise -Difference between Professional and Non-professional-
Hashimoto, Takeo (1), Hatano, Shigeko (1), Shin, Sung-Hwan (2)
(1) Seikei University, Japan
(2) Kookmin University, South Korea
ABSTRACT
The evaluation of Diesel powertrain noise on unpleasantness for good sound quality is different between professional and non-professional due to the difference of the key sounds to evaluate. The professional pays more on the frequency component related to the sensation of annoyance caused by the Diesel knocking. To compare the professional evaluation, the one obtained by the non-professional is based on the overall impression of test sound. In order to match the evaluation between the professional and non-professional, training session for correct evaluation is required for non-professional subject. If non-professional subject experiences the training session to know the point of evaluation, the evaluation obtained after the training is well match with the professional subject.
Full Paper
A Study on sound quality evaluation index of car door latch and improving sound quality by modifying door latch assembly design
Jo, Hyeonho (1), Seong, Weonchan (1), Lee, Hyeongrae (1), Kim, Seonghyeon (2), Park, Dongchul (2), Kang, Yeon June (1)
(1) Seoul National University, Republic of Korea
(2) Hyundai Motor Company, Republic of Korea
ABSTRACT
The purpose of this study is to develop an index that evaluates the sound quality of the door latches and improves the sound quality based on the results. To conduct the jury evaluation, various operating sounds of door latches were used. Through the results of the jury evaluations, loudness and sharpness related metrics are dominant in the sound quality index we developed. This research investigates the main transfer path of operating sounds through sound field visualization and concludes what could reduce the impact sound of the door latch. Therefore, we could verify the sound quality improvement of modified products by using the sound quality index.
Full Paper
In-service measurement of heavy vehicle engine brake noise
Kean, Simon (1), Bullen, Robert (2), Arredondo, Jose (3)
(1) Roads and Maritime Services, Australia
(2) Wilkinson Murray Pty Ltd, Australia
(3) National Transport Commission, Australia
ABSTRACT
Heavy vehicle engine compression brake noise is a major source of community annoyance due to its modulated characteristic. Traditional acoustic measurement approaches using A-weighted Sound Pressure Level have had moderate success but remained problematic. A new approach has been developed using instantaneous loudness to more accurately measure how the community hears the noise. From this an in-service test procedure and criterion has been developed to assist with potential compliance and enforcement processes. The proposed criterion was established by reviewing 170,000 roadside vehicle passbys and controlled tests using various engine silencer designs and is based on the RMS modulation of loudness in Sones. The controlled tests established the modulation scores that could reasonably be achieved with the current heavy vehicle fleet.
Full Paper
Influence of low SPL and bird twittering sounds on the loudness for road traffic noise
Kuwano, Kazuki (1), Yoshida, Junji (1)
(1) Osaka Institute of Technology, Japan
ABSTRACT
In this study, an influence of the frequency of low sound pressure level (SPL) on the loudness for road traffic noise was investigated. Road traffic noises were recorded and edited to have the same equal equivalent noise level (LAeq) and having different frequency of low SPL. Through a subjective loudness evaluation test, road traffic noises having more frequency of low SPL were evaluated significantly softer even though all sounds hadthesameLAeq.Improvementofthememorytothelow SPLsoundwasconsideredtobeimportantrolefor the result. Subsequently, several bird twittering sounds were inserted to a road traffic noise to change the attention and memory of the participants. The twittering sounds were added in high or low SPL section of the road traffic noise and subjective evaluation was performed again. Results show the sound including the twittering sounds were not evaluated softer, oppositely, the loudness decrease effect by the increase of the low SPL frequency was reduced.
Full Paper
A psychoacoustic assessment of road traffic noise for indoor aural comfort in high-rise built environment
Sheikh, Mahbub Alam (1), Lee, Siew Eang (1)
(1) National University of Singapore, Singapore
ABSTRACT
Research over the past few decades investigated noise annoyance in indoor residential settings and related it to several physical noise indicators such as LAeq, LA1, LA10, LAmax, LD, LN, LDEN etc. Recent researches show that A-weighted level is unable to consider mutual masking among the components in a complex sound and also the asymmetry of masking patterns produced in the auditory system. Rationally, A-weighted noise level is found as a poor indicator of loudness and annoyance. In contrary to the negative evaluation, research on the positive assessment of indoor aural environment and its association with different psychoacoustic parameters are very limited in the literature. This research investigates the indoor aural comfort in high-rise residential setting and its correlations with several psychoacoustic indicators. A psychoacoustic experiment was carried out to investigate indoor aural comfort subjected to road traffic noise and its relationships with different psychoacoustic indices. Loudness and Roughness were found significantly correlated with the assessment of 'Noisiness of Apartment' and 'Noise Disturbance' in indoor environment subjected to road traffic noise. Road traffic noise with a maximum Loudness of 9 Sone and a maximum Roughness of 27 centi-Asper were found attributing to a 'quiet' indoor aural environment. This paper presents statistical models for subjective 'noisiness of apartment' and 'noise disturbances' and discusses their relationships with these psychoacoustic quantities.
Full Paper
Simulation of gear rattle to aid in the development of sound quality metrics for diesel engine component specification
Sobecki, Brandon (1), Davies, Patricia (1), Bolton, J. Stuart (1)
(1) Purdue University, USA
ABSTRACT
Noise produced by components in a diesel affect the quality of the engine noise. One component source related to consumer complaints is gear rattle. Gear rattle is caused by gear tooth impacts resulting from fluctuations in differential torsional acceleration of the driving gears. Previous work in this area has focused on rating the overall sound quality of diesel engines without specifically focusing on models for predicting the perception of gear rattle. Here, a method to generate sounds having different levels of gear rattle is described. First, diesel engine noise recordings are analyzed to determine the engine speed time histories; they are then used to guide gear impact timing and to generate gear noise components. The gear noise transfer paths have been tuned to improve the quality of the gear noise predictions. The gear noise simulation tool is being used to generate sounds for subjective tests designed to quantify the detectability, perception of growth, and annoyance of gear rattle. The noise prediction coupled with the sound quality models based on the analysis of the subjective data will provide a way to predict how people perceive gear rattle so that component noise targets can be set directly related to human perception.
Full Paper
Influences of Vehicle Exterior Images on Sound Quality Ratings: German vs. Japanese Drivers
Yoshida, Junji (1), Volk, Florian (2), Fastl, Hugo (2), Rigoll, Gerhard (3)
(1) Osaka Institute of Technology, Japan, AG Technische Akustik, MMK, Technische Universität München, Germany
(2) Technische Universität München, Germany
(3) MMK, Technische Universität München, Germany
ABSTRACT
In this study, influences of vehicle exterior images on sound quality ratings of acceleration sounds were investigated. Luxury and sporty vehicle images were presented to German or Japanese frequent drivers, while listening to acceleration sounds. Subsequently, loudness, luxury, and sportiness of the sounds were rated. The results indicate that the German drivers tended to rate loudness lower and luxury higher when the sounds were presented with images of luxury cars, compared to images of sporty vehicles. As expected, sportiness was rated higher when an image of a sporty vehicle was presented. Oppositely the Japanese drivers indicated higher loudness and lower luxury when the sounds were combined with luxury vehicle images. Further, comparable to the German drivers, they rated higher sportiness when presented with sporty vehicle images. Consequently, it appears that sound quality ratings can be affected by the vehicle exterior design, but the average tendencies suggest different effect directions for German vs. Japanese drivers.
Full Paper
Virtual in-ear microphone for in-vehicle noise control based on array technology and modified zero point attraction LMS algorithms
Adnadjevic, Mirjana (1), Botteldooren, Dick (1)
(1) Ghent University, Belgium
ABSTRACT
Measuring in the ear of an operator of a vehicle or heavy duty machine may be useful in several applications such as noise assessment, adaptive communication, headphone-less binaural sound reproduction, or active noise control. However, wearing in-ear microphones is not very comfortable for the operator. Therefore, we investigated the possibility to replace these microphones by virtual microphones based on an array of microphones optimally located in an enclosure. Several modifications to LMS based algorithms for sparse MISO system identification were proposed and adopted at the one hand to eliminate as many of the filter taps as possible to reduce the computational load, and at the other hand eliminate as many microphones as possible to reduce hardware costs. Identification methods are evaluated through the simulations based on the experimental measurements performed in the real size driver's cabin constructed for the purpose of active noise control (ANC). Forty six microphones were initially positioned at the cabin roof, while virtual location is chosen to be ear of the seated observer. It is shown that these algorithms indeed reduce the set of microphones, still providing acceptable fitting performance when compared to the reference NLMS technique where all available microphones are used. Sensitivity of converged coefficients to natural head movements is evaluated for the head rotations of 20, 45 and 60 degrees in horizontal plane.
Full Paper
Wideband acoustical holography
Hald, Jorgen
Brüel & Kjaer Sound & Vibration Measurement A/S, Denmark
ABSTRACT
Patch NAH methods like SONAH and ESM are limited to relatively low frequencies where the average array inter-element spacing is less than half a wavelength, while beamforming provides useful resolution only at medium-to-high frequencies. With adequate array design, both methods can be used with the same array. But for holography to provide good low-frequency resolution, a small measurement distance must be used, while beamforming requires a larger distance to limit sidelobe issues. Wideband Holography was developed to overcome that practical conflict. Only a single measurement is needed at a relatively short distance and a single result is obtained covering the full frequency range. The underlying problem solved is that at high frequencies, the microphone spacing is too large to meet the spatial sampling criterion, and thus there is no unique reconstruction of the sound field. A reconstruction must therefore have a built-in "preference" for specific forms of the sound field. Doing just a Least Squares solution will result in reconstructed sound fields with sound pressure equal to the measured pressure at the microphones, but very low elsewhere. By building in a preference for compact sources, a smoother form of the reconstructed sound field is enforced.
Full Paper
Development of the Double NAH method
Nagamatsu, Masao
Hokkaido University of Science, Japan
ABSTRACT
There are several types of sound localization methods. But in sound localization of low frequency noise, all methods do not have enough resolution in reconstructed images. In this paper, the new localization method, Double Nearfield Acoustic Holography method is proposed. This method is converted method of conventional Nearfield Acoustic Holography method, and the purpose of this method is to improve the resolution of low frequency sound localization. In this paper, the theory of proposing method is explained. The several numerical simulations are done to verify the resolution of reconstructed images about sound localization in low frequency. In this paper, some numerical simulation results are explained. As a result, It is verified that the proposing method has better resolution on reconstructed images compared with conventional Nearfield Acoustic Holography method, in sound localization of low frequency sound sources.
Full Paper
Multi-spectral acoustical imaging
Nakamura, Kentaro (1), Guo, Xinhua (2)
(1) Tokyo Institute of Technology, Japan
(2) Wuhan University of Technology, China
ABSTRACT
Visualization of object through acoustic waves is generally called as acoustical imaging. This concept contain noise source localization, ultrasonic non-destructive testing, medical ultrasound, underwater sonars, etc. In these conventional imaging techniques, frequency information has not yet utilized effectively, though shape, material and even structure behind the surface reflect on the frequency characteristics of their acoustic responses. In this report, we introduce a concept of multi-spectral acoustical imaging, where wide range of frequency responses are investigated with a fine frequency pitch. As typical examples, we demonstrate the responses from a surface with several different holes for the frequency band from 1 to 20 kHz with 30-Hz pitch. The position and depth of the holes are clearly identified by their resonance frequencies. The volume of a small droplet in a well can be precisely measured using the present method. A method for displaying the multi-spectral acoustical data is also discussed.
Full Paper
Creation of a single sound field for multiple listeners
Poletti, Mark Alister (1), Betlehem, Terence (1)
(1) Callaghan Innovation, New Zealand
ABSTRACT
Sound reproduction systems are limited in their ability to create sound fields over large areas and over wide bandwidths, because the required number of loudspeakers becomes prohibitive. This limits the ability of surround systems to create sound fields large enough to be heard by multiple listeners. This paper considers an alternative approach to the creation of a single sound field for multiple listeners in which reproduction is accurate in a number of small zones of sufficient size for each listener. This results in a significant reduction in loudspeaker requirements compared to the creation of a single zone that encompasses all listeners. The approach is based on conversion of the sound field coefficients of the global field into localized coefficients within each zone and a mode-matching method for simultaneously reproducing the local fields in each zone. The theory is developed for the 2D case, for simplicity, and simulations are presented to demonstrate the effectiveness of the approach. Such a system would require a tracking system to determine the position of each listener, but the tracking requirements would be less stringent than are required for binaural reproduction using a cross talk canceller.
Full Paper
A microphone position calibration method in a reverberant environment for a randomly distributed array
Teng, Pengxiao (1), Xiao, Ying (2), Yang, Yichun (1)
(1) Chinese Academy of Sciences, China
(2) Shandong Universityof Science and Technology, China
ABSTRACT
distributed large-size array in this paper. The microphone positions need to be known exactly in order to localize sound sources. Time delay estimation (TDE) is an important step in calibrating the microphone positions using a few calibrating sound sources for a randomly distributed array. However, TDE method degrades severely in a reverberant environment which can introduce serious position errors. The microphone position error analysis is made due to misleading estimation of time delay. In this paper, impulsive sound source as a calibrating source is investigated compared with chirp source and white noise. The direct sound from an impulsive sound is isolated to calculate exact time delay in a reverberant environment while early reflection and reverberation sound are cut off. The simulation experiments are carried out to demonstrate that accurate microphone positions can be obtained using the proposed method. The proposed method is also applied in a project to calibrate the microphone positions for a spiral-like ceiling-mounted array with 64 elements and aperture of 3.5m, which proves the effectiveness.
Full Paper
A study on the influence of model uncertainties on the performance of a feedback control based ASAC system
Bagha, Ashok K (1), Modak, S V (1)
(1) Department of Mechanical Engineering, Indian Institute of Technology Delhi, Hauz Khas, New Delhi-110016, India
ABSTRACT
An important problem in systems such as aerospace interiors, automobile passenger compartments and other cavities is the control of low frequency interior noise. Active control of this noise may offer a potentially better alternative to passive control due to constraints of weight and space. Active structural-acoustic control (ASAC) is considered as an attractive strategy especially for controlling structure-borne noise. LQG based feedback control is one of the popular strategies that has been used in the context of ASAC. The LQG based strategies utilize an observer that estimates the states of the plant for feedback and therefore is a key element in the whole control loop. Since it uses a copy of the model of the plant for estimation, the accuracy of the model is crucial for its performance. This paper reports a study on the influence of the model uncertainties on the LQG based ASAC system. The influence of the uncertainties on the accuracy of the estimated states as well as on the closed loop system performance is studied. Uncertainties in material properties, geometry and boundary conditions are considered. Study on a rectangular box cavity with a flexible plate is reported.
Full Paper
Active Noise Control Experiments for an Acoustic-Structural Coupled Enclosure using Structural-Based Virtual Sensors
Halim, Dunant (1), Cheng, Li (2)
(1) Department of Mechanical, Materials and Manufacturing Engineering,University of Nottingham Ningbo, China
(2) Department of Mechanical Engineering, Hong Kong Polytechnic University, Hong Kong
ABSTRACT
This work was focused on the implementation of an active noise control strategy for an acoustic-structural coupled enclosure using structural-based virtual sensors. A virtual sensing system was developed to estimate the broadband sound pressure at virtual interior locations in the enclosure based on structural vibration measurement of its flexible structure, instead of using acoustic sensors. Experiments on a panel-cavity test rig were performed and an active control system using the FX-LMS algorithm was used to minimize the noise at a virtual location based on accelerometer measurements. Experiment results showed that the broadband noise level at the virtual location was suppressed even when the actual system dynamics was perturbed from the original one, demonstrating the robustness of active noise control system.
Full Paper
Semi-active noise suppression based on SSD technique using piezoelectric elements
Ji, Hongli (1), Cheng, Li (2), Qiu, Jinhao (3), Nie, Hong (3)
(1) Nanjing University of Aeronautics and Astronautics, China, Hong Kong Polytechnic University, Hong Kong
(2) Hong Kong Polytechnic University, Hong Kong
(3) Nanjing University of Aeronautics and Astronautics, China
ABSTRACT
Noise suppression using piezoelectric elements has received extensive attention in recent years. Traditional active noise control methods usually require the use of microphones as sensors to directly measure the sound pressure in either feed-forward or feedback control schemes. This makes the traditional active noise isolation more difficult to implement in some practical applications. Nonlinear semi-active Synchronized Switch Damping (SSD) approaches are typical switched-voltage control methods, which have recently been a topic of active research in the field of vibration control. In this paper, SSD method is proposed for the suppression of noise transmission through an aluminum panel. In a typical SSD setting, microphones are not required for feedback control, but are used merely as sensors to evaluate the control performance. The layout of the piezoelectric elements on the panel has been optimized based on the mode shape dominating the noise radiation. SSDV (SSD based on voltage sources) was used to improve the control performance. Experimental results show that the proposed control approach exhibits good performance in suppressing noise transmission.
Full Paper
Combined force-moment actuator for ASAC
Jiricek, Ondrej (1), Jandak, Vojtech (1), Brothanek, Marek (1)
(1) CTU in Prague, Czech Republic
ABSTRACT
This paper deals with a recently developed actuator based on piezoelectric bimorphs which are useful for ASAC applications. The actuator takes the form of two channels with pairs of bimorphs. Each of the bimorph transducers in the couple is connected separately so that the actuator can act in both moment and force configurations simultaneously. The control algorithm allows the ratio between the moment and force excitation to be adapted according to the desired mechanical output. The ASAC system using this actuator was tested on a simple structure in the form of a fixed beam. Configurations with maximum attenuation were selected and discussed.
Full Paper
Analysis of frequency-domain active noise control algorithm with parallel structure
Lee, Nokhaeng (1), Park, Youngjin (1)
(1) KAIST, Republic of Korea
ABSTRACT
Active noise control is a noise reduction technique introducing a canceling anti-noise wave. Recently, it is widely used in industrial operations, manufacturing, and consumer products. In many cases, periodic noise occurs because most applications include engines, compressors, motors, fans, and propellers which have reciprocating motion. The noise usually contains tones at the fundamental frequency and at several higher harmonic frequencies in practice. For this type of noise, we developed a frequency-domain active noise control algorithm and determined that it's effective before. In practice, however, some errors can occur and deteriorate the performance of the algorithm. In this paper, we consider that practical condition and have an analytical approach to the property of frequency-domain active noise control algorithm. We achieved the dynamics of the algorithm and predict the performance in practice.
Full Paper
Active vibration control using compliant-based actuators
Mareta, Sannia (1), Halim, Dunant (1), Popov, Atanas (2)
(1) University of Nottingham Ningbo, China
(2) University of Nottingham, UK
ABSTRACT
In this work, an active vibration control method using compliant-based actuators is proposed for controlling a wide range of vibration and its noise-associated applications. The compliant-based actuator combines a conventional actuator with elastic elements, such as passive springs, that can be demonstrated to have better accuracy and robustness for force control compared to conventional stiff actuators. At high frequencies, the actuator behaves like a passive spring with low impedance, providing a better shock resistance to the actuator than the stiff actuator. These capabilities are beneficial for developing an effective vibration isolation system, particularly for controlling the vibration transmissibility at important low frequencies. The effect of compliant stiffness on the vibration control performance is investigated. It is shown that Proportional-Derivative (PD) control method using a compliant-based actuator can be used to obtain effective control of force transmissibility at low frequencies.
Full Paper
On synchrophasing control of vibration for a floating raft vibration isolation system
Yang, Tiejun (1), Zhou, Liubin (2), Brennan, Michael J (3), Zhu, Minggang (1), Liu, Zhigang (1)
(1) Harbin Engineering University, China
(2) Wuhan Second Ship Design and Research Institute, China
(3) UNESP, Brazil
ABSTRACT
A large-scale floating raft vibration isolation system installed on a flexible hull-like structure is described in this paper. Four vibration exciters, in which two counter rotating shafts with the same balanced masses are driven by a phase asynchronous motor, are used to simulate rotating machines on the raft. The phase of the electrical supply to the motors is adjusted by synchrophasing control scheme to reduce the vibration transmitted to the host structure to which the machinery raft is attached. This kind of synchrophasing control for the floating raft vibration isolation system is investigated theoretically and experimentally. At last some results are presented and discussed.
Full Paper
Cyclic pitch for the control of
wind turbine noise amplitude modulation
Bertagnolio, Franck (1), Madsen, Helge Aagaard (1), Fischer, Andreas (1), Bak, Christian (1)
(1) DTU Wind Energy, Denmark
ABSTRACT
Using experimental data acquired during a wind turbine measurement campaign, it is shown that amplitude modulation of aerodynamic noise can be generated by the rotating blades in conjunction with the atmospheric wind shear. As an attempt to alleviate this phenomenon, a control strategy is designed in form of a cyclic pitch of the blades. As a side effect, it is shown that it is also possible to reduce fatigue load on the blade using this cyclic pitch. The main goal is to reduce both amplitude modulation and fatigue load without compro- mising the energy harvested from the wind. A simulation tool that can model the different aerodynamic and aeroacoustic aspects of the study is presented. Parameters controlling the cyclic pitch are optimized in order to reduce amplitude modulation and/or fatigue load to a minimum. It is shown that such a minimum can be found and that benefit may be achieved if such a strategy is to be implemented on an actual wind turbine, though at the expense of an increased wear and tear of the pitch control system.
Full Paper
Tonal characteristics of wind turbine drive trains
Dawson, Bill (1), Mackenzie, Neil (1)
(1) Aurecon, Australia
ABSTRACT
Wind turbines use a drive train incorporating a rotor, gearbox and generator to harness power from turning of the turbine blades. Modern wind turbine drive trains utilise a multi-stage gearbox, typically involving a planetary gear stage (low speed shaft) and two parallel stages (mid and high speed shafts). These gearboxes have natural frequencies and mode-shapes dependent upon the stiffness of gear shafts and tooth pairs, which can interact with tonal sources such as gear meshing frequencies to result in audible tones, and greatly increase the annoyance factor of wind farms and adversely impact on human health. This paper examines the drive train of a wind turbine, the impact on environmental noise emissions from the turbine, and how tonal characteristic issues associated with its operation may be avoided.
Full Paper
Application of stochastic wind model to investigate swishing characteristics of infrasound and low frequency noise from wind turbine
Lee, Gwang-Se (1), Cheong, Cheolung (1)
(1) Pusan National University, South Korea
ABSTRACT
Swishing characteristics of infrasound and low frequency noise radiating from a modern large horizontal-axis wind turbine are investigated by employing stochastic wind model to reproduce realistic incident wind conditions upstream of the wind turbine. The stochastic wind is generated through the superposition of colored noise on mean wind profile. The colored noise is computed by applying low-pass filter to white noise. The filter represents the geometric and atmospheric conditions around the target turbine. The wind profiles generated in this way are applied to compute aerodynamic response on blades of the wind turbine by using the XFOIL code. The computed airfoil response is finally incorporated to predict the infrasound and low frequency noise of the wind turbine by using the Lowson's acoustic analogy. When only the mean wind profile is applied, the swishing effects in the predicted time-frequency